Home

href="
Quick Installation Guide  
RCT8100  
Programmable Thermostat  
href="
Do you need assistance?  
We are here to help.  
Call 1-800-468-1502.  
href="
RCT8100 Programmable Thermostat  
Installation is Easy  
Your new thermostat has been designed for fast and  
easy installation. Just follow the simple step-by-step  
instructions in the following pages.  
n Identify your system type.  
o Remove your old thermostat.  
p Identify the wires.  
q Mount the new wallplate.  
r Connect the wires.  
s If the wire labels don’t match.  
t Specify the furnace type.  
u Install the batteries.  
v Install the thermostat.  
w Set the system.  
1
href="
Quick Installation Guide  
1
.
Identify System Type  
This thermostat is compatible with the following  
systems:  
n
Gas, oil or electric furnace  
Central air conditioner  
a hot water system with or without pump  
a millivolt system  
a central heating and cooling system  
If you are not sure of your system type or if you have  
any other questions, call us toll-free at 1-800-468-1502.  
This thermostat is not compatible with  
heat pumps or multi-stage systems.  
2
href="
RCT8100 Programmable Thermostat  
2
.
Remove Old Thermostat  
Turn power off at the heating/cooling system.  
o
1
)
2)  
Remove old thermostat, but leave wallplate with  
wires attached.  
Do not remove wallplate yet.  
MERCURY NOTICE: Do not put your old  
thermostat in the trash if it contains mercury in a  
sealed tube. Contact your local waste  
management authority for instructions regarding  
recycling and proper disposal.  
3
href="
Quick Installation Guide  
3
.
Identify Wires  
p
If any wires are not attached to your old thermostat or are  
attached to a terminal marked C or C1, they will not be  
connected to your new thermostat. Wrap the bare metal end  
of each of these wires with electrical tape, so it cannot touch  
and short other wires.  
Do not use  
non-connected wires.  
Do not use C or C1 wires  
Identify and label each wire.  
IGNORE WIRE COLORS:  
Use terminal screw  
designations to identify  
wires.  
Disconnect wires and remove the old wallplate only  
after all wires are labeled. Wrap the wires around  
a pencil to prevent them from falling though the  
wall opening.  
4
href="
RCT8100 Programmable Thermostat  
4
.
q Mount New Wallplate  
1)  
Remove coverplate.  
2)  
Loosen screw (the  
screw remains  
captive on wallplate).  
3
)
)
Remove thermostat.  
4
Mark and drill  
appropriate mounting  
holes (or use existing  
holes). Insert plastic  
anchors. Pass wires  
through opening of  
wallplate and secure  
Lab we al sl l pd l ao tne  tt om t ah te c wh ?a ll  
If a wiredo esnotm atch any terminal on the thermostat,  
see next page.  
5
href="
Quick Installation Guide  
5
.
r Connect Wires (typical wiring)  
Removejumper  
if you have both  
R and Rc wires.  
1)  
2)  
3)  
Match each labeled wire with the terminal having  
the same letter.  
Loosen the terminal screws using a screwdriver,  
insert the wires, then tighten the screws.  
Push any excess wire back into the wall opening.  
6
href="
RCT8100 Programmable Thermostat  
Connect Wires (less common wiring)  
If a labeled wire does not match any terminal  
designation, see diagram below.  
s
Do not use C, X or B. Wrap bare end of wire  
with electrical tape.  
If wires are connected to both Rh and Rc  
terminals, remove jumper (see previous  
page).  
7
href="
Quick Installation Guide  
6
.
Specify Furnace Type  
Set the Jumper J2, on the back of the thermostat, if  
you have connected a wire to the G terminal.  
t
J2 jumper  
Leave the jumper in this factory-set  
position if you have a gas or oil furnace.  
HG  
HE  
Place the jumper to this position if you  
have an electric furnace.  
8
href="
RCT8100 Programmable Thermostat  
7
.
u Install Batteries  
1
)
)
Pull out the battery cover.  
2
Install the batteries as shown. Observe the  
polarity.  
3)  
Reinstall the battery cover. You will hear a clicking  
sound.  
After the batteries are installed, the thermostat per-  
forms a series of tests for approximately 5 seconds.  
Afterwards, the screen displays the actual tempera-  
ture. It is normal that the displayed temperature be  
higher than the ambient temperature if you are holding  
the thermostat. The thermostat will display the ambient  
temperature once it is installed on the wall. By default,  
the setpoint is 70 °F (21 °C).  
9
href="
Quick Installation Guide  
8
.
v Install thermostat  
1)  
Mount the thermostat  
on the wallplate.  
2)  
Tighten the screw  
and install the  
coverplate.  
3)  
Turn power back on  
at the heating/cooing  
system.  
1
0
href="
RCT8100 Programmable Thermostat  
9
.
System Setup  
Press both and buttons simultaneously for 3  
seconds to enter or exit the setup menu.  
w
1
2
3
)
)
)
To advance to the next function, briefly press both  
and buttons simultaneously.  
To change the setting, press the or button.  
OPTIONS 1  
°C or °F  
DISPLAY  
DESCRIPTION  
Temperature display  
Time display  
12 h or 24 h  
On or Off  
Early Start 2  
Heating cycles per hour 3  
Cooling cycles per hour 3  
2, 3, 4, 5 or 6 4  
2, 3, 4, 5 or 6 5  
1
Default settings are shown in bold and underlined.  
See page 3 of Operating Manual.  
2
3
4
Use the system switch to switch between the two parameters.  
For optimal heating control, use the setting that matches your sys-  
tem as follows: 2=30 min (steam, gravity), 3=20 min (hot water,  
0%+ high-efficiency furnace), 4=15 min (gas or oil), 5=12 min  
alternate setting for gas or oil), 6=10 min (electric).  
9
(
5
The corresponding cooling cycle lengths are as follows: 2=30 min,  
=20 min, 4=15 min, 5=12 min, 6=10 min  
3
11  
href="
Quick Installation Guide  
Automation and Control Systems  
Honeywell International Inc.  
1
985 Douglas Drive North  
Golden Valley, MN 55422  
Honeywell Limited  
3
5 Dynamic Drive  
Scarborough, Ontario M1V 4Z9  
Printed in USA  
6
9-2336ES-01  
10-09  
1
2
href="
Guía de instalación rápida  
RCT8100  
Termostato programable  
href="
¿
Necesita asistencia?  
Estamos aquí para ayudarlo  
Llame al 1-800-468-1502  
href="
Termostato programable RCT8100  
Instalación fácil  
El nuevo termostato ha sido concebido para que su  
instalación sea fácil. Sólo hay que seguir las  
instrucciones de las páginas siguientes.  
n Identificar el tipo de sistema.  
o Retirar el viejo termostato.  
p Identificar los cables.  
q Montar la nueva placa mural.  
r Conectar los cables.  
s Cuando los cables no coinciden.  
t Especificar el tipo de estufa.  
u Instalar las pilas.  
v Instalar el termostato.  
w Configurar el sistema.  
1
href="
Guía de instalación rápida  
1
.
Identificar el tipo de sistema  
Este termostato es compatible con los siguientes  
sistemas:  
n
Calefactor a gas, aceite o eléctrico  
Aire acondicionado central  
Sistema de agua caliente con o sin bomba  
Sistema de milivoltios  
Sistema de calefacción y aire acondicionado  
central  
Si no supiera cuál es su sistema o si tuviera otras  
preguntas, llámenos sin cargo al 1-800-468-1502.  
Este termostato no es compatible con las bombas  
de calor o los sistemas multietapas.  
2
href="
Termostato programable RCT8100  
2
.
Retirar el viejo termostato  
Cortar la electricidad del sistema de calefacción/  
aire acondicionado.  
o
1
)
2)  
Retirar el viejo termostato pero dejar la placa  
mural con los cables conectados.  
No retirar la placa mural todavía  
ADVERTENCIA SOBRE EL MERCURIO:  
no ponga su viejo termostato en la basura si  
contiene mercurio en un tubo sellado.  
Comuníquese con la autoridad de gestión de  
desechos local para saber cómo reciclarlo o  
eliminarlo adecuadamente.  
3
href="
Guía de instalación rápida  
3
.
Identificar los cables  
p
Si en el viejo termostato hubiera cables no conectados o si  
estuvieran fijados a un terminal marcado C o C1, estos  
cables no se conectarán al nuevo termostato. Recubrir el  
extremo de metal desnudo de cada uno con cinta aisladora  
para que no puedan tocarse y producir un corto circuito.  
No utilizar cables  
no conectados  
No utilizar cables C o C1  
Identificar y etiquetar  
cada cable.  
IGNORAR LOS COLORES  
DE LOS CABLES:  
usar las designaciones de  
los tornillos terminales para  
identificar los cables.  
Desconectar los cables y retirar la vieja placa mural  
sólo después de haber identificado y etiquetado los  
cables. Enroscarlos en un lápiz para impedirles  
caer dentro del agujero de la pared.  
4
href="
Termostato programable RCT8100  
4
.
q Instalar la nueva placa mural  
1)  
Retirar la placa de  
cubierta.  
2)  
Aflojar los tornillos  
(que quedarán  
cautivos en la placa  
mural).  
3
)
)
Retirar el termostato.  
4
Marcar y perforar los  
agujeros de montaje  
apropiados (o usar  
los existentes).  
Introducir los  
anclajes plásticos.  
Pasar los cables por  
la apertura de la  
placa mural y  
¿
Las etiquetas no coinciden?  
Si un cable no corresponde a ningún terminal  
del termostato, referirse a la página siguiente.  
tornillos provistos.  
5
href="
Guía de instalación rápida  
5
.
r Conectar los cables (conexión típica)  
Retirar el puente  
si hay cables R y  
Rc.  
1)  
2)  
3)  
Hacer coincidir cada cable etiquetado con el  
terminal de la misma letra.  
Aflojar los cables del terminal con un  
destornillador, luego ajustar los tornillos.  
Empujar el exceso de cables en el agujero de la  
pared.  
6
href="
Termostato programable RCT8100  
Conectar los cables (conexión menos común)  
s
Si un cable etiquetado no coincide con la designación  
de ningún terminal, referirse al diagrama siguiente:  
No usar C, X o B. Enroscar el extremo  
desnudo con cinta aisladora.  
Si los cables están conectados con los  
terminales Rh y Rc, retirar el puente (ver la  
página previa).  
7
href="
Guía de instalación rápida  
6
.
Especificar el tipo de estufa  
La posición del cable de puente J2, en la parte poste-  
rior del termostato, es importante si se conectó un  
cable al terminal G.  
t
Puente J2  
Dejar el puente en esta posición en el  
caso de un sistema de calefacción a gas  
o a aceite.  
HG  
HE  
Colocar el puente en esta posición en el  
caso de un sistema de calefacción eléc-  
trico.  
8
href="
Termostato programable RCT8100  
7
.
u Instalar las pilas  
1
)
)
Retirar la cubierta de las pilas.  
2
Instalar las pilas como se indica en el dibujo.  
Respetar la polaridad.  
3)  
Reinstalar la cubierta de las pilas. Se escuchará  
un clic.  
Luego de instalar las pilas, el termostato hace una  
serie de pruebas por alrededor de 5 segundos.  
Una vez terminadas las pruebas, la pantalla indicará  
la temperatura actual. Es normal que la temperatura  
indicada sea más elevada que la temperatura  
ambiente si se tiene el termostato en la mano. El ter-  
mostato indicará la temperatura ambiente cuando esté  
instalado en la pared. El punto de ajuste de fábrica es  
de 70°F (21°C).  
9
href="
Guía de instalación rápida  
8
.
v Instalar el termostato  
1)  
Montar el termostato  
en la placa mural.  
2)  
Ajustar los tornillos e  
instalar la placa de  
cubierta.  
3)  
Conectar el sistema  
de calefacción/aire  
acondicionado a la  
electricidad.  
1
0
href="
Termostato programable RCT8100  
9
.
Configuración del sistema  
w
1
)
Presionar los botones  
y
simultáneamente durante 3  
segundos para entrar o salir del menú de configuración.  
2
)
Para avanzar a la siguiente función, presionar brevemente  
simultáneamente.  
y
3
)
Para cambiar la configuración, presionar los botones  
o
.
OPCIONES 1  
°C ó °F  
PANTALLA  
DESCRIPCIÓN  
Visualización de temperatura  
Visualización de la hora  
12 h ó 24 h  
Encendido anticipado2  
On ó Off  
Ciclos de calefacción/hora 3  
Ciclos de enfriamiento/hora 3  
2, 3, 4, 5 ó 6 4  
2, 3, 4, 5 ó 6 5  
1
2
3
4
Lo valores de fábrica están en negrita y subrayados.  
Ver la página 3 del Manual de Uso.  
Usar el conmutador del sistema para cambiar entre los dos parámetros.  
Para un control óptimo de la calefacción, utilizar la configuración  
correspondiente al sistema de la siguiente manera: 2=30 min. (vapor/  
gravedad); 3=20 min. (agua caliente, 90%+ calefactor de alta eficacia);  
4
6
5
=15 min. (gas o aceite), 5=12 min. (ajuste alterno para gas o aceite);  
=10 min. (eléctrico).  
La duración de los ciclos de aire acondicionado correspondientes son  
los siguientes: 2=30 min., 3=20 min., 4=15 min., 5=12 min., 6=10 min.  
11  
href="
Guía de instalación rápida  
Sistemas para automatización y control  
Honeywell International Inc.  
1
985 Douglas Drive North  
Golden Valley, MN 55422  
Honeywell Limited  
3
5 Dynamic Drive  
Scarborough, Ontario M1V 4Z9  
Impreso en EE.UU.  
6
9-2336ES-01  
10-09  
1
2