Honeywell RRTH9590WF Thermostat User Manual

Home

Quick Start Guide

Wi-Fi Color Touchscreen

Programmable Thermostat

RTH9590 Wi-Fi With Voice Control

Welcome

Getting set up and ready is simple.

Install your thermostat.

Connect your home Wi-Fi network.

Before you begin

You will also need:

•ꢀ Smallꢀscrewꢀdriver

•ꢀ Pen

View the installation video at

wifithermostat.com/support

You will need your camera

to take a picture of your old

wire connections.

•ꢀ ThermostatꢀIDꢀcardꢀ

•ꢀ YourꢀhomeꢀWi-Fiꢀ

network password

Installꢀyourꢀthermostat

.1 Switch OFF power to your

heating/cooling system

.1a Important! To protect your

equipment, switch OFF the

power to your heating/

cooling system at the

breaker box or the system

switch.

Circuit

breaker

box

Heating/cooling

system power

switch

.1b Confirm power is OFF.

Try to turn on heating/

cooling equipment by

changing temperature

on your old thermostat.

Your power is OFF if your

system does not turn ON.

This thermostat works with common 24

volt systems such as forced air, hydronic,

heat pump, oil, gas, and electric. It will not

work with millivolt systems, such as a gas

fireplace, or with 120/240 volt systems such

as baseboard electric heat.

.2 Remove old thermostat

faceplate and leave wires

connected

Note: You will need a

picture of your wire

connections to wire the

new thermostat.

.2a Take a picture of the wire

connections for later

reference.

ꢀꢀꢀꢀ1.2bꢀꢀIfꢀnoꢀwireꢀisꢀconnectedꢀtoꢀa ꢀ

terminal labeled C or no C

terminal exists on the old

thermostat, view the

Alternate Wiring videos at

wifithermostat.com/videos

Important! C wire is required

and is the power source for your

thermostat. Without a C wire, your

thermostat will not power up.

Terminal

designation

M33823A

If you have an older thermostat with a

sealed mercury tube, see warning page

for proper disposal instructions.

1.3 Label wires

Stickyꢀtag

Do not label by wire color.

Use the supplied sticky tags to label

each wire as you disconnect it. Label

wires according to old thermostat

terminal designations, not by wire

color.

Note: Ifꢀnoꢀtagꢀmatchesꢀaꢀterminalꢀ

designation, write the appropriate

letter on a blank sticky tag.

Blank tags

Note: Wrap the wires around a pencil

to prevent them from falling back into

the wall.

1.4 Remove wallplate

Remove the old wallplate from

the wall after all wires are

labeled and disconnected.

Terminal

designation

.5 Mount wallplate for Wi-Fi

thermostat

Mount your new wallplate using

screws and anchors included

with the thermostat.

ꢀ

Ifꢀnecessary:

Wallplate

•ꢀ Drillꢀ3/16-inꢀholesꢀforꢀdrywall

•ꢀ Drillꢀ7/32-inꢀholesꢀforꢀplasterꢀ

LEVEL

HERE

W-

O/B

Note: You may be able to use

your existing wall anchors. Hold

the wallplate up to the existing

anchors to check for alignment.

W2-

Aux/E

1.6 Connect wires

Important! C wire is required and

is the power source. Without a C wire,

your thermostat will not power up.

Note: The wiring for your application

might be different than the wiring

shown below.

View the Alternate Wiring videos

at wifithermostat.com/videos

Terminal release

.6aꢀ StartingꢀwithꢀtheꢀCꢀWire,ꢀmatchꢀ

the sticky tag on the wire to the

terminal labels.

W-

O/B

ꢀ

1.6bꢀ Straightenꢀwireꢀandꢀgentlyꢀslideꢀꢀ

W2-

Aux/E

into terminal hole until it clicks

ꢀ

intoꢀplace.ꢀ(Ifꢀyouꢀneedꢀtoꢀꢀ ꢀ

remove a wire, use a pen tip to

press the terminal release and

then pull the wire out.)

EXAMPLE WIRING

Yours may look different

Note: Refer to the wiring picture

youꢀtookꢀinꢀStepꢀ1.2.

Remove jumper loop ONLY if

you have both R and Rc wires.

ꢀ

Tip: To make it easier to slide the

wire into place, use a pen tip to

hold down the terminal release.

Labels don’t match or have

heat pump system?

SeeꢀUser Guide.

ꢀ

1.6cꢀ Inꢀtheꢀimageꢀonꢀtheꢀright,ꢀcheckꢀꢀ

the box next to each connection.

You will use this checklist in

Important!

Check the box for each wire

you connect. You will need

thisꢀinformationꢀinꢀStepꢀ1.9.

ꢀ

Stepꢀ1.9.

1.6dꢀ Verifyꢀwireꢀisꢀfirmlyꢀsecuredꢀbyꢀꢀ

gently pulling on wire.

W-O/B

ꢀ

1.6eꢀ Repeatꢀstepsꢀa–d for all other

wires.

1.6fꢀ Pushꢀany excess wire back into

the wall opening after all wires

are installed.

W2-Aux/E

Note: The L terminal on the lower

right is used only for Heat Pump

systems.

Labels don’t match or have

heat pump system?

SeeꢀUser Guide.

Note: IfꢀtheꢀoldꢀthermostatꢀforꢀHeatꢀ

PumpꢀSystemꢀhasꢀseparateꢀwiresꢀ

on Aux and E, use a wire nut to

attach both wires to a separate

wire.ꢀSlideꢀthisꢀthirdꢀwireꢀintoꢀtheꢀ

W2-Aux/E terminal.

.7 Attach thermostat

LEVEL

HERE

to wallplate

Wallplate

Align the thermostat with

wallplate and snap into

place.

Thermostat

.8 Switch heating/cooling

system ON

Important!

.8a Verify that the C wire is

connected at the thermostat

and at the heating/cooling

system.

.8b Make sure the heating/

cooling system door is

firmly secured.

Circuit

breaker

box

Heating/cooling

system power

switch

ꢀ

1.8cꢀ SwitchꢀpowerꢀbackꢀONꢀforꢀꢀ ꢀ

your heating/cooling system

at the breaker box or its

power switch.

1.9 Select setup

Before connecting to your Wi-Fi

network, you need to set initial

thermostat options to define your

heating/cooling system:

ꢀ

•ꢀꢀꢀLanguage

•ꢀꢀꢀHomeꢀorꢀbusiness

Follow prompts on the screen to

select appropriate options.

.9a Touch the language you want

the thermostat to display, then

touch Next.

ꢀ

1.9bꢀ SelectꢀHomeꢀorꢀBusinessꢀꢀ ꢀ

application, then touch Next.

1.9c Touch Next or name the

thermostat location—touch

THERMOSTATꢀandꢀfollowꢀtheꢀꢀ ꢀ

rest of the instructions.

ꢀ

1.9dꢀ Selectꢀwhatꢀyourꢀthermostatꢀwillꢀꢀ

control and touch Next.

1.9eꢀ Selectꢀyourꢀsystemꢀtypeꢀandꢀꢀ

touch Next The system type

determines other selection for

completing initial setup. Use

ꢀ

theꢀchecklistꢀfromꢀStepꢀ1.6ꢀwhenꢀꢀ

making selections.

1.9f Touch Next after making

selections on each screen.

.9g Touch Done on the last screen.

The thermostat displays an option

to connect to your Wi-Fi network.

Connect to your Wi-Fi network

.1 Connect the Wi-Fi network

After touching Done on the final screen

ofꢀtheꢀinitialꢀsetꢀupꢀ(Stepꢀ1.9g),ꢀtheꢀꢀ

thermostat displays an option to

connect to your Wi-Fi network.

ꢀ

Yes

.1a Touch Yes to connect the

thermostat to your Wi-Fi

network. The screen displays the

ꢀ

ꢀꢀꢀꢀꢀꢀꢀꢀꢀmessageꢀ“Searchingꢀforꢀwirelessꢀ

networks. Please wait...” after

which it displays a list of all Wi-Fi

networks it can find.

Note:ꢀIfꢀyouꢀcannotꢀcompleteꢀthisꢀstepꢀꢀ

now, touch I’ll do it later. The thermostat

will display the home screen. Complete

this process by selecting MENU > Wi-Fi

Setup.ꢀContinueꢀwithꢀStepꢀ2.1b.

.1b Touch the name of the network

you want to use. The thermostat

displays a password page.

Public

Your Network

Neighbor

.1c Using the keyboard, touch the

characters that spell out your

home network password.

.1d Touch Done. The thermostat

displays “Connecting to your

network. Please wait...” then

showsꢀaꢀ“ConnectionꢀSuccessful”ꢀꢀ

screen.

ꢀ

Note: Ifꢀyourꢀhomeꢀnetworkꢀisꢀnotꢀ

shown on the list, touch Rescan

2.1e Touch Next to display the

Done

registration information screen.

Getting Help

If you get stuck...

At any point in the Wi-Fi connection process, restart the thermostat by

removing the thermostat from the wallplate, wait for 5 seconds, and snap it

back into place. From the home screen, touch MENU > Wi-Fi Setup > Choose a

Network.ꢀContinueꢀwithꢀStepꢀ2.1b.

Need more help?

Find additional information in the User Guide.

This thermostat works with common 24 volt systems such as forced air, hydronic,

heatꢀpump,ꢀoil,ꢀgas,ꢀandꢀelectric.ꢀItꢀwillꢀnotꢀworkꢀwithꢀmillivoltꢀsystems,ꢀsuchꢀasꢀaꢀ

gas fireplace, or with 120/240 volt systems such as baseboard electric heat.

MERCURY NOTICE:ꢀDoꢀnotꢀplaceꢀyourꢀoldꢀthermostatꢀinꢀtheꢀtrashꢀifꢀitꢀcontainsꢀ

mercury in a sealed tube. Contact the Thermostat Recycling Corporation at

www.thermostat-recycle.orgꢀorꢀ1-800-238-8192ꢀforꢀinformationꢀonꢀhowꢀandꢀ

where to properly and safely dispose of your old thermostat.

NOTICE: To avoid possible compressor damage, do not run air conditioner if the

outside temperature drops below 50°F (10°C).

To register your thermostat, follow the

instructionsꢀonꢀStepꢀ3.1.

Note: The Register Online screen remains

active until you complete registration and/or

touch Done.

Note:ꢀIfꢀyouꢀtouchꢀDone before you register

online, your home screen displays an

orange alert button telling you to register.

Touching that button displays registration

information and an option to snooze the

task.

Done

online for

remote

access

Press for info

To view and set your Wi-Fi thermostat

remotely, you must have a Total Connect

Comfort account. Follow the instructions

below.

View the Wi-Fi Thermostat

Registration video at

wifithermostat.com/videos

.1 Open the Total Connect

Comfort web site

Go to www.mytotalconnectcomfort.com

3.2 Login or create an account

Ifꢀyouꢀhaveꢀanꢀaccount,ꢀ

click Login

ꢀ

–ꢀorꢀ–

click Create An Account.

ꢀ

3.2aꢀ Followꢀtheꢀinstructionsꢀonꢀtheꢀꢀ

ꢀ

screen.

3.2bꢀ Check your email for a response

from My Total Connect Comfort.

This may take several minutes.

Note: Ifꢀyouꢀdoꢀnotꢀreceiveꢀaꢀresponse,ꢀ

check your junk mailbox or use an

alternate e-mail address.

3.2cꢀ Follow activation instructions

in the email.

ꢀ

3.2dꢀ Logꢀin.

.3 Register your Wi-Fi thermostat

Thermostat ID Card

Use the MAC ID and CRC ID to register

this product at mytotalconnectcomfort.com

After you are logged in to your Total

Connect Comfort account, register your

thermostat.

HONEYWELL MODEL:

MAC ID:

MAC CRC:

Carte d’identification de thermostat

Utilisez l’identiﬁcation MAC et l’identiﬁcation CRC pour

enregistrer ce produit à mytotalconnectcomfort.com

Tarjeta de identificación del termostato

Utilice la identiﬁcación MAC y la identiﬁcación CRC para

inscribir este producto en mytotalconnectcomfort.com

ꢀ

3.3aꢀ Followꢀtheꢀinstructionsꢀonꢀtheꢀ

screen. After adding your

U.S. Registered Trademark.

2012 Honeywell International Inc.

9-2723EFS—01 M.S. 04-12

thermostat location you must enter

your thermostat’s unique identifiers:

Printed in U.S.A.

69-2723EFS-01

ꢀ

•ꢀ MACꢀID

MACꢀID

MAC CRC

•ꢀ MACꢀCRC

Note: TheseꢀIDsꢀareꢀlistedꢀon the

ThermostatꢀIDꢀCardꢀincludedꢀinꢀtheꢀꢀ

thermostatꢀpackage.ꢀTheꢀIDsꢀareꢀnotꢀ

case sensitive.

ꢀ

3.3b Notice that when the thermostat is

successfully registered, the Total

Connect Comfort registration

ꢀ

screenꢀwillꢀdisplayꢀaꢀSUCCESSꢀꢀ

message.

You can now control your thermostat

from anywhere through your laptop,

tablet, or smartphone.

Getting started with voice

For information on how to control your

thermostat with voice, see the included

“Talking with your Thermostat” card.

Note that the voice commands for this

thermostat are in English only.

Need help?

Visitꢀwifithermostat.comꢀorꢀcallꢀ1-888-235-6569ꢀ

for assistance before returning the thermostat

to the store.

GET IT ON

Total Connect Comfort free app is available

for Apple iPhone , iPad and iPod touch

devices at iTunes or at Google Play for

all Android™ devices.

Download on

iTunes

9-2791-03

Automation and Control Systems

HoneywellꢀInternationalꢀInc.

985ꢀDouglasꢀDriveꢀNorth

Golden Valley, MN 55422

wifithermostat.com

®ꢀU.S.ꢀRegisteredꢀTrademark.

Apple,ꢀiPhone,ꢀiPad,ꢀiPodꢀtouchꢀandꢀiTunesꢀareꢀtrademarksꢀofꢀAppleꢀInc.ꢀ

All other trademarks are the property of their respective owners.

ꢀ2013ꢀHoneywellꢀInternationalꢀInc.

9-2791—03ꢀꢀM.S.ꢀꢀRev.ꢀ07-13ꢀ

PrintedꢀinꢀU.S.A.