Aprilaire 61000652C 8400 Tstat Thermostat User Manual

TAblE Of CONTENTS

INSTAllATION

Installation location recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Outdoor temperature sensor (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Thermostat mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Power & reset options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Wiring terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

SETUp & TESTINg

System setup instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

System test mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

REfERENCES

Quick reference to controls & display

ꢀ

•ꢀNon-programmableꢀmodelsꢀ(8444,ꢀ8446,ꢀ8448) . . . . . . . . . . . . . . . . . . . . . . . . . . 22

•ꢀProgrammableꢀmodelsꢀ(8463,ꢀ8465,ꢀ8466) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Thermostat features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

1000652C 8400 Tstat Install.indd

10/13/09 11:08:56 AM

Thermostatꢀcanꢀbeꢀmountedꢀtoꢀaꢀverticalꢀjunctionꢀbox.

INSTAllATION

INSTAllATION lOCATION RECOꢀꢀENDATIONS

Thermostat shouꢁd ꢂe mounted:

Do not mount thermostat:

•ꢀ

Onꢀanꢀinteriorꢀwall,ꢀinꢀaꢀfrequentlyꢀoccupiedꢀspace.

Approximatelyꢀ5‘ꢀaboveꢀfloor.

•ꢀ

appliancesꢀthatꢀgiveꢀoffꢀheat.

Atꢀleastꢀ18”ꢀfromꢀoutsideꢀwall.

•ꢀ

ꢀ

•

outside doors

•

ꢀ

1000652C 8400 Tstat Install.indd

10/13/09 11:08:57 AM

•

WhenꢀtheꢀoutdoorꢀtemperatureꢀisꢀhigherꢀthanꢀtheꢀHighꢀ

BalanceꢀPoint,ꢀtheꢀauxiliaryꢀheatingꢀwillꢀbeꢀlockedꢀoutꢀ

andꢀonlyꢀtheꢀheatꢀpumpꢀwillꢀbeꢀusedꢀtoꢀprovideꢀheating.

INSTAllATION

OUTDOOR TEꢀpERATURE SENSOR (OpTIONAl)

Outdoorꢀtemperatureꢀcanꢀbeꢀmeasuredꢀbyꢀattachingꢀanꢀ

•ꢀInstallꢀonꢀsideꢀofꢀbuildingꢀoutꢀofꢀdirectꢀsunlightꢀ

052ꢀsensorꢀtoꢀtheꢀS1ꢀandꢀS2ꢀterminals.ꢀSystemꢀsettingꢀ

05ꢀ(Remoteꢀsensor)ꢀisꢀusedꢀtoꢀenableꢀsensor.ꢀ

(north side recommended)

•

ꢀ

Heat pump models can use the outdoor temperature to

effectivelyꢀutilizeꢀtheꢀheatꢀpump:

•

condensing lines

•

ꢀ

WhenꢀtheꢀoutdoorꢀtemperatureꢀisꢀlessꢀthanꢀtheꢀLowꢀ

BalanceꢀPoint,ꢀtheꢀheatꢀpumpꢀwillꢀbeꢀlockedꢀoutꢀandꢀ

onlyꢀauxiliaryꢀheatingꢀwillꢀbeꢀused.ꢀ

•

ꢀ

•

C S1 S2 O/B

L W2 Y2

1000652C 8400 Tstat Install.indd

10/13/09 11:08:57 AM

Sealꢀwireꢀentryꢀholesꢀtoꢀpreventꢀdraftsꢀaffectingꢀ

INSTAllATION

THERꢀOSTAT ꢀOUNTINg

pOwER & RESET OpTIONS

Theꢀthermostatꢀisꢀdualꢀpower.ꢀItꢀcanꢀeitherꢀbeꢀACꢀorꢀ

batteryꢀpowered,ꢀorꢀbothꢀ(toꢀprovideꢀbackupꢀpowerꢀforꢀ

theꢀclock).ꢀBatteriesꢀareꢀoptionalꢀifꢀtheꢀthermostatꢀwasꢀ

connectedꢀtoꢀACꢀpowerꢀwhenꢀinstalled.

Forꢀheatꢀpumpꢀmodelsꢀ(8446,ꢀ8448HP,ꢀ8465,ꢀ8466HP)ꢀ

4ꢀVACꢀmustꢀbeꢀconnectedꢀinꢀorderꢀforꢀtheꢀsystemꢀfaultꢀ

and emergency heat indicators to operate

Theꢀthermostatꢀhasꢀaꢀmemoryꢀbackupꢀthatꢀsavesꢀtheꢀ

thermostat’sꢀsettingsꢀinꢀcaseꢀofꢀaꢀpowerꢀinterruption.ꢀ

Theꢀresetꢀbuttonꢀlocatedꢀunderꢀtheꢀbatteryꢀcoverꢀcanꢀbeꢀ

usedꢀtoꢀresetꢀtheꢀthermostatꢀbackꢀtoꢀfactoryꢀdefaults.ꢀ

Theꢀsystemꢀsettingsꢀwillꢀalsoꢀbeꢀresetꢀbackꢀtoꢀdefaults.ꢀ

.ꢀ

Removeꢀtheꢀbackꢀofꢀtheꢀthermostat,ꢀbyꢀpressingꢀtheꢀ

tabꢀonꢀtheꢀbottomꢀofꢀtheꢀunit.ꢀ

.ꢀ

Pullꢀwiresꢀthroughꢀtheꢀopeningꢀonꢀtheꢀbackꢀofꢀtheꢀ

thermostat

Positionꢀandꢀlevelꢀtheꢀbackꢀofꢀtheꢀthermostatꢀonꢀwallꢀ

and mark the hole locations with a pencil

4.ꢀ

5.ꢀ

6.ꢀ

Drillꢀ1/4”ꢀholesꢀ&ꢀinsertꢀsuppliedꢀanchorsꢀ(drywallꢀonly).

Placeꢀbackꢀoverꢀanchors,ꢀinsertꢀandꢀtightenꢀscrews.

temperature readings

1000652C 8400 Tstat Install.indd

10/13/09 11:08:58 AM

•

ꢀ

Pushꢀtheꢀexcessꢀwireꢀbackꢀintoꢀtheꢀopeningꢀandꢀplugꢀ

theꢀwallꢀopeningꢀtoꢀpreventꢀdrafts.

INSTAllATION

wIRINg TERꢀINAl

wire sꢃeciꢄications

RCꢀ–ꢀ24ꢀVACꢀsupplyꢀcooling*

Rꢀ–ꢀ24ꢀVACꢀsupplyꢀheating*

8-24ꢀgaugeꢀthermostatꢀwire

wꢀ–ꢀ1stꢀstageꢀheatꢀ/ꢀauxiliary

Yꢀ–ꢀ1stꢀstageꢀcoolingꢀ/ꢀcompressorꢀ

g – Fan

Cꢀ–ꢀCommonꢀ(optionalꢀwhenꢀpoweredꢀbyꢀbatteries)

S1 & S2 – outdoor temperature sensor (optional)

O/bꢀ–ꢀReversingꢀvalve

Instaꢁꢁation notes

•

ꢀ

EnsureꢀpowerꢀatꢀtheꢀHVACꢀequipmentꢀisꢀoff.ꢀ

•

Loosenꢀscrewꢀterminals,ꢀinsertꢀstrippedꢀwireꢀandꢀ

re-tighten.

l – System fault indicator

w2ꢀ–ꢀ2ndꢀstageꢀheatꢀ/ꢀauxiliary

Y2ꢀ–ꢀ2ndꢀstageꢀcoolingꢀ/ꢀcompressor

Jumper between RC & R is used in single transformer systems

see wiring diagrams).

(

C S1 S2 O/B L W2 Y2

1000652C 8400 Tstat Install.indd

10/13/09 11:08:58 AM

INSTAllATION

wIRINg – ꢀODEl 8463 & 8444 SINglE

TRANSfORꢀER (USE jUꢀpER wIRE)

wIRINg – ꢀODEl 8463 & 8444 TwO

TRANSfORꢀERS (REꢀOVE jUꢀpER wIRE)

S1 S2

C S1 S2

1000652C 8400 Tstat Install.indd

10/13/09 11:08:58 AM

INSTAllATION

wIRINg – ꢀODEl 8465 & 8446 SINglE

TRANSfORꢀER (USE jUꢀpER wIRE)

wIRINg – ꢀODEl 8465 & 8446 TwO

TRANSfORꢀERS (REꢀOVE jUꢀpER wIRE)

S1 S2 O/B

C S1 S2 O/B

1000652C 8400 Tstat Install.indd

10/13/09 11:08:58 AM

INSTAllATION

wIRINg – ꢀODEl 8466 & 8448 SINglE

TRANSfORꢀER (USE jUꢀpER wIRE)

fOR HEAT/COOl SYSTEꢀ

wIRINg – ꢀODEl 8466 & 8448 TwO

TRANSfORꢀERS (REꢀOVE jUꢀpER wIRE)

fOR HEAT/COOl SYSTEꢀ

S1 S2 O/B

W2 Y2

C S1 S2 O/B

L W2 Y2

1000652C 8400 Tstat Install.indd

10/13/09 11:08:58 AM

INSTAllATION

wIRINg – ꢀODEl 8466 & 8448 SINglE

TRANSfORꢀER (USE jUꢀpER wIRE)

fOR HEAT pUꢀp SYSTEꢀ

wIRINg – ꢀODEl 8466 & 8448 TwO

TRANSfORꢀERS (REꢀOVE jUꢀpER wIRE)

fOR HEAT pUꢀp SYSTEꢀ

S1 S2 O/B

W2 Y2

C S1 S2 O/B

L W2 Y2

1000652C 8400 Tstat Install.indd 10

10/13/09 11:08:59 AM

SETUp & TESTINg

SYSTEꢀ SETUp INSTRUCTIONS

Theꢀfollowingꢀinstructionsꢀshowꢀhowꢀtoꢀenterꢀtheꢀsystemꢀsetupꢀmenuꢀandꢀchangeꢀsettings.ꢀTheꢀtableꢀonꢀtheꢀ

followingꢀpagesꢀlistsꢀtheꢀsettingsꢀandꢀtheirꢀdetails.ꢀDefaultꢀsettingsꢀareꢀshownꢀinꢀꢂoꢁd Some settings are only

availableꢀtoꢀcertainꢀmodels,ꢀandꢀsomeꢀareꢀspecificꢀtoꢀthermostatsꢀsetꢀtoꢀheatꢀpumpꢀmode.

Hoꢅ to enter the system setuꢃ menu to chanꢆe

system settinꢆs

press

to change the setting

ꢀtoꢀchangeꢀtoꢀtheꢀnextꢀoption.

press

repeatedly until system is set to OFF

press

displayed

ꢀafterꢀtheꢀlastꢀsetting.ꢀ“DONE”ꢀwillꢀbeꢀ

press and hoꢁd

and

for three seconds

Theꢀscreenꢀofꢀtheꢀfirstꢀsettingꢀwillꢀbeꢀdisplayed.ꢀ

TheꢀthermostatꢀwillꢀreturnꢀtoꢀNormalꢀmodeꢀifꢀnoꢀkeyꢀisꢀ

pressed in 3 seconds

Toꢀresetꢀallꢀsystemꢀsettingsꢀbackꢀtoꢀdefault,ꢀpressꢀtheꢀ

RESETꢀbuttonꢀlocatedꢀunderꢀtheꢀbatteryꢀdoor.

SETTINGꢀVALUE

SYSTEMꢀSETTINGꢀNUMBER

1000652C 8400 Tstat Install.indd 11

10/13/09 11:08:59 AM

SETUp & TESTINg

SYSTEꢀ SETUp INSTRUCTIONS (CONTINUED)

Thermostatꢀmodelsꢀ8448ꢀ&ꢀ8466ꢀhaveꢀtheꢀoptionꢀofꢀbeingꢀusedꢀinꢀheatꢀpumpꢀorꢀheat/coolꢀsystems.ꢀSwitchꢀSW1ꢀ

locatedꢀonꢀtheꢀbackꢀofꢀtheꢀthermostat’sꢀfaceꢀisꢀusedꢀtoꢀselectꢀthis.ꢀSystemꢀsettingꢀnumberꢀ00ꢀwillꢀonlyꢀbeꢀshownꢀonꢀ

these models to display the position of SW1

Sw1

HEATꢀPUMP

HEAT/COOL

1000652C 8400 Tstat Install.indd 12

10/13/09 11:08:59 AM

SETUp & TESTINg

SYSTEꢀ SETUp INSTRUCTIONS (CONTINUED)

System settinꢆ

Settinꢆ ranꢆe, deꢄauꢁt in ꢂoꢁd

ꢀ:ꢀheat/cool

ꢀ:ꢀheatꢀpump

0ꢀꢀEquipmentꢀtypeꢀ(8466,ꢀ8448)ꢀ(Set ꢂy Sw1)

: fahrenheit

1 Temperature scale

ꢀ:ꢀCelsius

: gas or oiꢁ ꢄurnace (Equiꢃment controꢁs ꢄan)

2 Fan control in heating

ꢀ:ꢀElectricꢀ(Thermostatꢀcontrolsꢀfan)

° : No oꢄꢄset aꢃꢃꢁied

3 Offset temperature for internal sensor

4ꢀꢀAutoꢀmode

–

4°Fꢀtoꢀ+4°Fꢀ(–2°Cꢀtoꢀ+2°C)

: Auto mode is disaꢂꢁed

ꢀ:ꢀAutoꢀmodeꢀisꢀenabled

: No outdoor temꢃerature sensor attached

5 Outdoor temperature sensor

6ꢀꢀCompressorꢀminimumꢀoffꢀtime

7 Heating minimum off time

8ꢀꢀEquipmentꢀminimumꢀonꢀtime

ꢀ:ꢀOutdoorꢀtemperatureꢀsensorꢀattached

minutes

to 5 minutes in 1 minute steps

minutes

to 5 minutes

minutes

to 5 minutes

1000652C 8400 Tstat Install.indd 13

10/13/09 11:08:59 AM

SETUp & TESTINg

SYSTEꢀ SETUp INSTRUCTIONS (CONTINUED)

System settinꢆ

Settinꢆ ranꢆe, deꢄauꢁt in ꢂoꢁd

°f (0.5°C)

°Fꢀtoꢀ4°Fꢀ(0.5°Cꢀtoꢀ2°C)

9 1st stage differential

°f (0.5°C)

°Fꢀtoꢀ4°Fꢀ(0.5°Cꢀtoꢀ2°C)

0ꢀꢀ2ndꢀstageꢀdifferentialꢀ(8448,ꢀ8466)

1ꢀꢀ3rdꢀstageꢀdifferentialꢀ(8448HP,ꢀ8466HP)

2ꢀꢀReverseꢀvalveꢀ(8446,ꢀ8466HP,ꢀ8465,ꢀ8466HP)

°f (0.5°C)

°Fꢀtoꢀ4°Fꢀ(0.5°Cꢀtoꢀ2°C)

– O/b enerꢆized in cooꢁinꢆ (O)

ꢀ–ꢀO/Bꢀenergizedꢀinꢀheatingꢀ(B)

3ꢀꢀI

ntegralꢀfactorꢀperiodꢀ(P+Iꢀcontrol)*

4 minutes

Set to OFF for proportional control only

1ꢀtoꢀ5ꢀminutesꢀorꢀ“OFF”ꢀtoꢀdisable

°f (2°C)

°Fꢀtoꢀ5°Fꢀ(1°Cꢀtoꢀ3°C)

4ꢀꢀDeadbandꢀ(autoꢀmode)

ꢀ:ꢀProgressiveꢀrecoveryꢀisꢀdisabled

5ꢀꢀProgressiveꢀrecoveryꢀ(8463,ꢀ8465,ꢀ8466)

: proꢆressive recovery is enaꢂꢁed

Theꢀintegralꢀfactorꢀisꢀusedꢀinꢀtheꢀequipmentꢀcontrolꢀalgorithmꢀtoꢀmaintainꢀtheꢀspaceꢀtemperatureꢀatꢀsetꢀpoint.ꢀ

Aꢀshortꢀintegralꢀfactorꢀperiodꢀwillꢀincreaseꢀtheꢀnumberꢀofꢀcyclesꢀperꢀhour.ꢀ(Aꢀshortꢀintegralꢀfactorꢀperiodꢀwillꢀbeꢀmoreꢀ

comfortable.)ꢀAꢀlongꢀintegralꢀfactorꢀperiodꢀwillꢀlowerꢀtheꢀnumberꢀofꢀcyclesꢀperꢀhour.ꢀ(Aꢀlongꢀintegralꢀfactorꢀperiodꢀwillꢀ

beꢀmoreꢀeconomical.)

1000652C 8400 Tstat Install.indd 14

10/13/09 11:09:00 AM

SETUp & TESTINg

SYSTEꢀ SETUp INSTRUCTIONS (CONTINUED)

System settinꢆ

Settinꢆ ranꢆe, deꢄauꢁt in ꢂoꢁd

6ꢀꢀL

owꢀBalanceꢀPt.ꢀ(8446,ꢀ8448HP,ꢀ8465,ꢀ8466HP)

20°f (–7°C)

1°Fꢀtoꢀ35°Fꢀ(–17°Cꢀtoꢀ1°C)ꢀorꢀ“OFF”ꢀtoꢀdisable

Systemꢀsettingꢀ05ꢀmustꢀbeꢀenabled

7ꢀꢀH

ighꢀBalanceꢀPt.ꢀ(8446,ꢀ8448HP,ꢀ8465,ꢀ8466HP)

60°f (16°C)

40°Fꢀtoꢀ80°Fꢀ(4°Cꢀtoꢀ27°C)ꢀorꢀ“OFFꢀ“ꢀtoꢀdisable

Systemꢀsettingꢀ05ꢀmustꢀbeꢀenabled

– 5/2 ꢃroꢆram (weekdays and weekends)

9ꢀꢀProgramꢀformatꢀ(8463,ꢀ8465,ꢀ8466)

ꢀ–ꢀ5/1/1ꢀprogramꢀ(Weekdays,ꢀSat.ꢀandꢀSun.)

Off

0ꢀꢀChangeꢀairꢀfilter

,ꢀ3,ꢀ6,ꢀ12ꢀmonthsꢀorꢀ“OFF”ꢀtoꢀdisable

1ꢀꢀC

hangeꢀwaterꢀpanel**

Off

Setꢀnumberꢀofꢀmonthsꢀuntilꢀreminderꢀisꢀrequired

1ꢀtoꢀ12ꢀmonthsꢀorꢀ“OFF”ꢀtoꢀdisable

: fꢁoꢅ throuꢆh tyꢃe humidiꢄier (1 reminder ꢃer season)

ꢀ:ꢀDrain-lessꢀtypeꢀhumidifierꢀ(2 reminders per season)

2ꢀꢀHumidifierꢀtype**

Off

3ꢀꢀServiceꢀdehumidifier

4ꢀꢀServiceꢀHVAC

ꢀtoꢀ12ꢀmonthsꢀorꢀ“OFF”ꢀtoꢀdisable

Off

ꢀtoꢀ12ꢀmonthsꢀorꢀ“OFF”ꢀtoꢀdisable

IfꢀhumidifierꢀtypeꢀisꢀsetꢀtoꢀDrain-less,ꢀthenꢀtheꢀfirstꢀreminderꢀisꢀbasedꢀonꢀtheꢀsystemꢀsettingꢀ21,ꢀsecondꢀreminderꢀ

willꢀactivateꢀ3ꢀmonthsꢀlater.ꢀꢀIfꢀhumidifierꢀtypeꢀisꢀsetꢀtoꢀFlowꢀthrough,ꢀthenꢀtheꢀfirstꢀreminderꢀisꢀbasedꢀonꢀsystemꢀ

settingꢀ21,ꢀsecondꢀreminderꢀwillꢀactivateꢀ12ꢀmonthsꢀlater.

1000652C 8400 Tstat Install.indd 15

10/13/09 11:09:00 AM

SETUp & TESTINg

SYSTEꢀ TEST ꢀODE

Theꢀsystemꢀtestꢀmodeꢀisꢀusedꢀtoꢀtestꢀaꢀsystemꢀafterꢀinstallation.ꢀTheꢀoutputsꢀofꢀtheꢀthermostatꢀcanꢀbeꢀmanuallyꢀ

activatedꢀoneꢀatꢀaꢀtimeꢀtoꢀtestꢀtheirꢀfunction.ꢀTheꢀfollowingꢀinstructionsꢀshowꢀhowꢀtoꢀenterꢀtheꢀtestꢀmodeꢀandꢀturnꢀ

outputs on and off The charts on the following pages show all of the options for each model

The test steꢃs are:

Test

Numꢂer

Heat/Cooꢁ ꢀodeꢁs

8444, 8463, 8448HC, 8466HC

Heat pumꢃ ꢀodeꢁs

8446, 8465, 8448Hp, 8466Hp

Heating (W) (W2)

Coolingꢀ(Y)ꢀ(Y2)

Fanꢀ(G)

AuxꢀHeatingꢀ(W)ꢀ(W2)

CompressorꢀCoolingꢀ(Y)ꢀ(Y2)

CompressorꢀHeatingꢀ(Y)ꢀ(Y2)

Fanꢀ(G)

1000652C 8400 Tstat Install.indd 16

10/13/09 11:09:00 AM

SETUp & TESTINg

SYSTEꢀ TEST ꢀODE (CONTINUED)

Hoꢅ to enter the system test menu

press

output,ꢀꢃress

ꢀtoꢀturnꢀonꢀtheꢀoutputꢀ(01).ꢀForꢀmultiꢀstageꢀ

ꢀagainꢀtoꢀturnꢀonꢀtheꢀ2ndꢀstageꢀ(02).

press

repeatedly until system is set to OFF

press and hoꢁd

and

for three seconds

press

ꢀtoꢀturnꢀoffꢀtheꢀoutputꢀ(00).

Theꢀscreenꢀofꢀtheꢀfirstꢀtestꢀstepꢀ#50ꢀisꢀdisplayed:ꢀ

ꢀtoꢀchangeꢀtoꢀtheꢀnextꢀtestꢀstep.

ꢀafterꢀtheꢀlastꢀtestꢀstep.ꢀ“DONE”ꢀwillꢀbeꢀ

press

displayed

TheꢀthermostatꢀwillꢀreturnꢀtoꢀNormalꢀmodeꢀifꢀnoꢀkeyꢀisꢀ

pressed in 3 seconds

FLASHESꢀIFꢀ24VACꢀ

ISꢀNOTꢀPRESENT

SYSTEMꢀTESTꢀ

NUMBER

MODEꢀ(SW1ꢀSETTINGꢀ

8448ꢀ&ꢀ8466ꢀONLY)

OUTPUTꢀSTATUS

1000652C 8400 Tstat Install.indd 17

10/13/09 11:09:00 AM

SETUp & TESTINg

Test steꢃs ꢄor 8444 & 8463

System Settinꢆ

Disꢃꢁay (Outꢃut)

fAN ON

(g)

Steꢃ

Key Inꢃut

HEATINg

ON (w)

COOlINg

ON (Y)

ꢀ:ꢀGas

[

UP]

50ꢀHeat

1ꢀ:ꢀElec

[

DOWN]

UP]

DOWN]

UP]

DOWN]

[

51ꢀCool

52 Fan

[

1000652C 8400 Tstat Install.indd 18

10/13/09 11:09:01 AM

SETUp & TESTINg

Test steꢃs ꢄor 8448HC & 8466HC

System Settinꢆ

Disꢃꢁay (Outꢃut)

fAN ON

(g)

Steꢃ

Key Inꢃut

HEATINg

ON (w)

HEATINg

ON (w2)

COOlINg

ON (Y)

COOlINg

ON (Y2)

ꢀ:ꢀGas

ꢀ:ꢀElec

0ꢀ:ꢀGas

ꢀ:ꢀElec

stꢀ[UP]

50ꢀHeat

ndꢀ[UP]

DOWN]

stꢀ[UP]

2ndꢀ[UP]

[

51ꢀCool

[

DOWN]

UP]

DOWN]

[

52 Fan

[

1000652C 8400 Tstat Install.indd 19

10/13/09 11:09:01 AM

SETUp & TESTINg

Test steꢃs ꢄor 8446 & 8465

System Settinꢆ

#12

Disꢃꢁay (Outꢃut)

1 AUX

fAN ON

(g)

Steꢃ

Key Inꢃut

HEATINg

ON (w)

COOl/HEAT

ON (Y)

O/b

ꢀ:ꢀGas

[

UP]

DOWN]

UP]

50ꢀAux

1ꢀ:ꢀElec

[

ꢀ:ꢀO

[

ꢀ:ꢀB

51ꢀCool

ꢀ:ꢀO

DOWN]

UP]

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

[

52 Heat

[

DOWN]

UP]

DOWN]

[

53 Fan

[

1000652C 8400 Tstat Install.indd 20

10/13/09 11:09:01 AM

SETUp & TESTINg

Test steꢃs ꢄor 8448Hp & 8466Hp

System Settinꢆ

Disꢃꢁay (Outꢃut)

1 AUX

02 AUX

Steꢃ

Key Inꢃut

#12

HEATINg

ON (w)

HEATINg COOl/HEAT COOl/HEAT fAN ON

O/b

ON (w2)

ON (Y)

ON (Y2)

(g)

ꢀ:ꢀGas

ꢀ:ꢀElec

0ꢀ:ꢀGas

ꢀ:ꢀElec

stꢀ[UP]

50ꢀAux

ndꢀ[UP]

DOWN]

stꢀ[UP]

[

ꢀ:ꢀO

ꢀ:ꢀB

ꢀ:ꢀO

51ꢀCool

2ndꢀ[UP]

DOWN]

stꢀ[UP]

2ndꢀ[UP]

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

ꢀ:ꢀO

ꢀ:ꢀB

[

52 Heat

[

DOWN]

UP]

DOWN]

[

53 Fan

[

1000652C 8400 Tstat Install.indd 21

10/13/09 11:09:02 AM

QUICK REfERENCE TO CONTROlS & DISplAY

NON-pROgRAꢀꢀAblE ꢀODElS (8444, 8446, 8448)

CURRENTꢀINDOORꢀTEMPERATURE

OUTDOORꢀTEMPERATUREꢀ(OPTIONAL)

TEMPERATUREꢀSETTING

SYSTEMꢀMODEꢀ

SETTING

EQUIPMENTꢀSTATUS

SYSTEMꢀMODE

FANꢀSETTING

DOWN

HEAT pUꢀp ꢀODElS ONlY

EMERGENCYꢀHEATꢀ(RED)

SYSTEMꢀFAULTꢀ(YELLOW)

FANꢀSETTING

INDICATORꢀSHOWSꢀTHROUGHꢀHOUSING

QUICKꢀREFERENCEꢀCARD

BATTERYꢀDOOR

MESSAGEꢀCENTER

LOWꢀBATTERYꢀWARNING

NOTE:ꢀBACKLIGHTꢀISꢀACTIVATEDꢀWITHꢀFIRSTꢀBUTTONꢀPRESSꢀANDꢀAUTOMATICALLYꢀTURNSꢀOFF.

1000652C 8400 Tstat Install.indd 22

10/13/09 11:09:02 AM

QUICK REfERENCE TO CONTROlS & DISplAY

pROgRAꢀꢀAblE ꢀODElS (8463, 8465, 8466)

CURRENTꢀINDOORꢀTEMPERATURE

CURRENTꢀTIME

OUTDOORꢀTEMPERATUREꢀ(OPTIONAL)

TEMPERATUREꢀSETTING

SYSTEMꢀMODEꢀ

SETTING

EQUIPMENTꢀSTATUS

FANꢀSETTING

SYSTEMꢀMODE

FANꢀSETTING

PROGRAM

DOWN

HOLD

HEAT pUꢀp ꢀODElS ONlY

EMERGENCYꢀHEATꢀ(RED)

SYSTEMꢀFAULTꢀ(YELLOW)

CURRENTꢀ

SCHEDULEꢀ

PERIOD

INDICATORꢀSHOWSꢀTHROUGHꢀHOUSING

QUICKꢀREFERENCEꢀCARD

BATTERYꢀDOOR

MESSAGEꢀCENTER

LOWꢀBATTERYꢀWARNING

NOTE:ꢀBACKLIGHTꢀISꢀACTIVATEDꢀWITHꢀFIRSTꢀBUTTONꢀPRESSꢀANDꢀAUTOMATICALLYꢀTURNSꢀOFF.

1000652C 8400 Tstat Install.indd 23

10/13/09 11:09:02 AM

THERꢀOSTAT fEATURES

All 8400 SERIES THERꢀOSTATS

pROgRAꢀꢀAblE ꢀODElS ONlY

8463, 8465, 8466)

(

•

ꢀ

Large,ꢀclear,ꢀbacklitꢀdisplayꢀisꢀeasyꢀtoꢀreadꢀ–ꢀevenꢀ

in the dark

•ꢀ

schedules

ꢀ

Displaysꢀroomꢀtemperature,ꢀtemperatureꢀsetting,ꢀandꢀ

optional outdoor temperature

program schedule at any time

•ꢀ

Dualꢀpowerꢀoptionꢀ(Batteryꢀorꢀ24ꢀVAC).

Frontꢀbatteryꢀdoorꢀaccessꢀforꢀfast,ꢀeasyꢀreplacement.

Builtꢀinꢀcompressorꢀprotection.

•

ꢀ

Circulationꢀfanꢀmodeꢀforꢀairꢀcleaning.

Waterꢀpanel,ꢀdehumidifier,ꢀairꢀfilter,ꢀandꢀHVACꢀ

serviceꢀindicators.

•

ꢀ

Systemꢀtestꢀmode.

1000652C 8400 Tstat Install.indd 24

10/13/09 11:09:02 AM

common.ꢀIfꢀvoltageꢀisꢀnotꢀpresent,ꢀcheckꢀtheꢀheatingꢀ

equipmentꢀtoꢀfindꢀtheꢀcauseꢀofꢀtheꢀproblem.

•

Ifꢀthermostatꢀisꢀbatteryꢀpowered,ꢀmakeꢀsureꢀfreshꢀAAꢀ

alkalineꢀbatteriesꢀareꢀcorrectlyꢀinstalled.

TROUblESHOOTINg

DISplAY IS blANK

HEATINg SYSTEꢀ DOES NOT RESpOND

“HEATINg” AppEARS ON SCREEN)

(

•

ꢀ

Checkꢀcircuitꢀbreakerꢀandꢀresetꢀifꢀnecessary.

•ꢀ

ꢀ

Makeꢀsureꢀpowerꢀswitchꢀatꢀheatingꢀ&ꢀcoolingꢀ

system is on

•

ꢀ

Makeꢀsureꢀfurnaceꢀdoorꢀisꢀclosedꢀsecurely.

TEꢀpERATURE SETTINgS DO NOT CHANgE

Makeꢀsureꢀheatingꢀandꢀcoolingꢀtemperaturesꢀareꢀsetꢀtoꢀ

acceptableꢀranges:

•

ꢀHeat:ꢀ45°ꢀtoꢀ90°Fꢀ(7°ꢀtoꢀ32°C).

ꢀCooꢁ:ꢀ50°ꢀtoꢀ99°Fꢀ(10°ꢀtoꢀ37°C).

•

1000652C 8400 Tstat Install.indd 25

10/13/09 11:09:03 AM

Checkꢀforꢀlooseꢀorꢀbrokenꢀwiresꢀbetweenꢀtheꢀ

thermostatꢀandꢀtheꢀcoolingꢀequipment.

TROUblESHOOTINg

COOlINg SYSTEꢀ DOES NOT RESpOND

HEAT/COOl bOTH ON AT SAꢀE TIꢀE

CheckꢀSW1ꢀ(EquipmentꢀType),ꢀtoꢀmakeꢀsureꢀitꢀisꢀsetꢀ

toꢀmatchꢀtheꢀinstalledꢀheating/coolingꢀequipmentꢀ

(see page 12)

(

“COOlINg” AppEARS ON SCREEN)

•

ꢀ

•

ꢀ

Checkꢀforꢀ24ꢀVACꢀatꢀtheꢀequipmentꢀonꢀtheꢀsecondaryꢀ

sideꢀofꢀtheꢀtransformerꢀbetweenꢀpowerꢀandꢀ

common.ꢀIfꢀvoltageꢀisꢀnotꢀpresent,ꢀcheckꢀtheꢀcoolingꢀ

equipmentꢀtoꢀfindꢀtheꢀcauseꢀofꢀtheꢀproblem.

ꢀ

not shorted together

Checkꢀforꢀ24ꢀVACꢀbetweenꢀtheꢀcoolingꢀterminalꢀ(Y)ꢀ

andꢀtheꢀtransformerꢀcommon.ꢀIfꢀ24ꢀVACꢀisꢀpresent,ꢀ

theꢀthermostatꢀisꢀfunctional.ꢀCheckꢀtheꢀcoolingꢀ

systemꢀtoꢀfindꢀtheꢀcauseꢀofꢀtheꢀproblem.

HEATINg EQUIpꢀENT IS RUNNINg IN

COOl ꢀODE

•

ꢀCheckꢀSW1ꢀ(EquipmentꢀType),ꢀtoꢀmakeꢀsureꢀitꢀisꢀsetꢀ

toꢀmatchꢀtheꢀinstalledꢀheating/coolingꢀequipmentꢀ

(see page 12)

fAN DOES NOT TURN ON IN A CAll fOR HEAT

“HEATINg” IS NOT DISplAYED

•

ꢀ

CheckꢀSystemꢀSettingꢀ#02ꢀ(FanꢀControl),ꢀtoꢀmakeꢀ

sure the fan control is properly set to match the type

of system (see page 11)

ꢀChangeꢀtheꢀSystemꢀModeꢀtoꢀHeat,ꢀandꢀsetꢀ

theꢀtemperatureꢀlevelꢀaboveꢀtheꢀcurrentꢀroomꢀ

temperature

HEAT pUꢀp ISSUES COOl AIR IN HEAT ꢀODE,

OR wARꢀ AIR IN COOl ꢀODE

“

COOlINg” IS NOT DISplAYED

ꢀ

•

ꢀ

CheckꢀSystemꢀSettingꢀ#12ꢀ(ReversingꢀValve),ꢀtoꢀmakeꢀ

sure it is properly configured for your system (see

page 11)

1000652C 8400 Tstat Install.indd 26

10/13/09 11:09:03 AM

SpECIfICATIONS

Environment

Operating:ꢀ32°ꢀtoꢀ120°Fꢀ(0°ꢀtoꢀ48.9°C)

Shipping:ꢀ-30°ꢀtoꢀ140°Fꢀ(-34.4°ꢀtoꢀ60°C)

Temperature

Relativeꢀhumidity

Operating:ꢀ5%ꢀtoꢀ90%ꢀR.H.ꢀ(non-condensing)

Eꢁectricaꢁ

Operatingꢀvoltage

Current

24ꢀVACꢀ(18ꢀ–ꢀ30ꢀVAC)

Maximum:ꢀ2.5Aꢀ(total),ꢀ1.0Aꢀ(singleꢀoutput)

Maximumꢀsurgeꢀcurrent:ꢀ5A

Dualꢀpower.ꢀCanꢀbeꢀbatteryꢀorꢀ24ꢀVACꢀpowered.

Power supply

Whenꢀbothꢀtheꢀsourcesꢀareꢀavailable,ꢀbatteryꢀwillꢀbeꢀusedꢀasꢀ

backꢀupꢀpower.

Batteryꢀpower:ꢀAAꢀsizeꢀalkalineꢀbatteryꢀxꢀ2

Batteryꢀlife:ꢀApproximatelyꢀ1ꢀyear

Batteryꢀpower

1000652C 8400 Tstat Install.indd 27

10/13/09 11:09:03 AM

SpECIfICATIONS

Thermaꢁ

Outdoor temperature sensor

Maximumꢀdistance:ꢀ300ꢀfeet

Displayꢀrange:ꢀ32°ꢀtoꢀ99°Fꢀ(0°ꢀtoꢀ40°C)

Displayꢀrange:ꢀ-20°ꢀtoꢀ130°Fꢀ(-30°ꢀtoꢀ55°C)

Roomꢀtemperatureꢀmeasurement

Outdoor temperature measurement

Heat:ꢀ45°ꢀtoꢀ90°Fꢀ(7°ꢀtoꢀ32°C)

Cool:ꢀ50°ꢀtoꢀ99°Fꢀ(10°ꢀtoꢀ37°C)

Temperature setting range

RESEARCHꢀPRODUCTSꢀCORPORATION

P.O.ꢀBOXꢀ1467ꢀ•ꢀMADISON,ꢀWIꢀ53701-1467ꢀ•ꢀꢅꢅꢅ.aꢃriꢁaire.com

1000652 10.09

B2204777C

1000652C 8400 Tstat Install.indd 28

10/13/09 11:09:03 AM