Aube TH108PLUS Thermostat User Manual

TH108PLUS

User Guide

Electronic Thermostat

NOTE: All cables and connections must conform to the local electri-

cal code. Special CO/ALR solderless connectors must be used when

connecting with aluminium conductors.

Percentageof

heating time *

Temperature

display

Temperature

adjustment

buttons

-wire installation

The thermostat displays the percentage of heating time required to

maintain the desired temperature. For example, is displayed when

heating is activated 40 percent of the time.

Description

This thermostat can be used to control an electric heating system

such as a baseboard heater, a radiant ceiling, a radiant floor, a con-

vector, etc.

-wire installation

The thermostat cannot be used with the following:

•

a resistive load under 2 A

a resistive load over 12.5 A

systems driven by a contactor or a relay (inductive load)

fan-equipped heating systems

central heating systems

SUPPLIED PARTS

Align and affix the base to the

electrical box.

•

One (1) thermostat

Two (2) 6-32 mounting screws

Two (2) solderless connectors

Installation

TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN

POWER PANEL TO AVOID ELECTRIC SHOCK.

Loosen the screw holding the control module to the base. The screw

cannot be completely removed. Lift the control module to remove it

from the base.

Set the switch at the back of the remov-

able part of the thermostat to °C or °F.

Replace the front part of the thermostat

on the base and secure it in place with

the screw.

NOTE: Keep the air vents of thermostat

Make the appropriate connections. Please note that the thermostat

clean and unobstructed at all times.

wires are non-polarized; either wire can be connected to either termi-

nal.

TH108PLUS

400-108-008-A

5/10/06

1/2

Temperature Display and Setting

The thermostat normally displays the actual (ambi-

Warranty

;

Aube warrants this product, excluding battery, to be free from defects

in the workmanship or materials, under normal use and service, for a

period of three (3) year from the date of purchase by the consumer. If

at any time during the warranty period the product is determined to

be defective or malfunctions, Aube shall repair or replace it (at Aube's

option).

ent) temperature.

•

To view the setpoint temperature, press once on

either temperature adjustment button. The icon

appears during the setpoint display.

•

To change the setpoint temperature, press the appropriate but-

ton until the desired value is displayed.

If the product is defective,

(i) return it, with a bill of sale or other dated proof of purchase, to

the place from which you purchased it, or

NOTE: The display is backlit for 10 seconds when either button is

pressed.

(

ii) contact Aube. Aube will make the determination whether the

product should be returned, or whether a replacement product

can be sent to you.

This warranty does not cover removal or reinstallation costs. This

warranty shall not apply if it is shown by Aube that the defect or mal-

function was caused by damage which occurred while the product

was in the possession of a consumer.

Power Outage

During a power outage, the setpoint is saved in memory. You do not

need to adjust the temperature when power returns.

Aube's sole responsibility shall be to repair or replace the product

within the terms stated above. AUBE SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCI-

DENTAL OR CONSEQUENTIAL DAMAGES RESULTING,

DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR-

RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF

THIS PRODUCT. Some provinces, states or regions do not allow the

exclusion or limitation of incidental or consequential damages, so this

limitation may not apply to you.

Specifications

Supply: 240 VAC, 50/60 Hz

Minimum load: 2 A (resistive only)

00 W @ 240 VAC

Maximum load: 12.5 A (resistive only)

000 W @ 240 VAC

Display range: 0 °C to 50 °C (32 °F to 122 °F)

Setpoint range: 5 °C to 30 °C (40 °F to 85 °F)

Storage: -20 °C to 50 °C (-4 °F to 120 °F)

Approval: c UL us

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE

MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED

WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANT-

ABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS

WARRANTY. Some provinces, states or regions do not allow limita-

tions on how long an implied warranty lasts, so the above limitation

may not apply to you.

s ^T^r^o^u^b^l^e^s^h^o^o^tⁱⁿ^g

This warranty gives you specific legal rights, and you may have other

rights which vary from one province, state or region to another.

PROBLEM

SOLUTIONS

This is normal. Under normal operation, the

thermostat housing can reach a temperature

between 35 °C (95 °F) and 40 °C (104 °F).

Customer assistance

If you have any questions about the product installation or operation,

or concerning the warranty, contact us at:

ꢀ

Thermostat is hot.

Correct if any the following conditions

applies:

05 Montrichard

Saint-Jean-sur-Richelieu, Quebec

J2X 5K8

Canada

•

The thermostat is exposed to air draft.

Displayed tempera-

ture is wrong.

The sticker on the thermostat’s screen

has not been removed.

•

The thermostat is located near or above

a heat source such as a light dimmer.

Tel.: (450) 358-4600

Toll-free: 1-800-831-AUBE

Fax: (450) 358-4650

The thermal protection device on the heater

Display disappears has temporarily opened. This can happen if

and reappears after the heater is obstructed by furniture or curtain

Email: aube.service@honeywell.com

a few minutes.

and has overheated, or if the heater’s thermal

protection device is too sensitive.

For more information on our products, go to

Display looks faded The heating system is less than the required

www.aubetech.com

when heating is

activated.

minimum load. This thermostat cannot be

used below that rating.

TH108PLUS

400-108-008-A

5/10/06

2/2