Aube TH110A SP P Thermostat User Manual

Home

href="
INSTALLATION  
NOTE : The "Problems and Solutions" section at the end of this user's guide will  
help you to correct your problems during the installation.  
This thermostat has been designed to operate with any installation  
which has a RESISTIVE load not exceeding 2400 W (20 A) @ 120 VAC  
such as electric baseboards, radiant ceilings and floors, electric con-  
vectors, etc. It is not compatible with a low voltage controller used by  
a central heating system.  
MODEL TH110A-SP-P (120 V)  
Electricians or experienced technicians should install the thermostat.  
SUMMARY  
u
This thermostat is designed to be used with a self-protected heating  
system equipped with thermal cut off and circuit breaker.  
OPTIONS SELECTION  
At the back of the thermostat, there are three selection switches to set at  
your preferences.  
PARTS INCLUDED  
Temperature in °C or °F, time in 12 or 24 hours and Early Start function.  
-
One (1) TH110A-SP-P (120 VAC) thermostat  
- Two (2) 6-32 screws  
Four (4) solderless connectors (for copper wire)  
u
u
TO SET TIME AND DAY  
-
Press on DAY, HOUR and MIN buttons to adjust time and day.  
TURN OFF POWER OF THE HEATING SYSTEM AT THE MAIN POWER  
PANEL TO AVOID ELECTRICAL SHOCK. Keep air vents of the thermostat  
clean and free from obstructions.  
TO RECORD THE  
Select chosen setpoint temperature by using  
button (2 to 3 seconds) until icon appears on display.  
(COMFORT) SETPOINT TEMPERATURE  
or button. Press on  
u
u
TO RECORD THE  
Select chosen setpoint temperature by using  
Press on button (2 to 3 seconds) until icon appears on display .  
(ECONOMY) SETPOINT TEMPERATURE  
or button.  
1
) Connecting wires and mounting thermostat  
Connect the rear thermostat wires to the 120 V LINE and to the load using  
solderless connectors for copper wires. See schematic diagram.  
TO RECORD THE  
To program the Vacation temperature, select the desired degree using the  
buttons and press on the and buttons simultaneously  
icon is displayed (app. 3 seconds).  
(VACATION) SETPOINT TEMPERATURE  
Push the excess wire back into the electrical box to prevent interference with the  
thermostat. Secure the thermostat using two (2) 6-32 screws. Once the  
thermostat is properly installed, return power to heating system.  
until the  
u
OPERATING MODES  
To select an operating mode, use MODE button.  
AUTO:  
Runs the program.  
and can override temporarily your programming up to the  
next program.  
or  
shows temperature setting  
SUPPLY  
BEFORE  
AFTER  
120 V LINE  
MAN:  
Maintains the selected temperature.  
the temperature setting.  
or  
changes  
OLD  
THERMOSTAT  
BLACK  
B
W
BLACK  
BLACK  
1
20 VAC  
B
B
WHITE  
W
W
60 HZ  
BLACK  
W
B
LOAD  
LOAD  
NOTE : All cables and connections must conform to the local electrical code.  
WARNING: Special CO/ALR solderless connectors must be used when  
connecting with aluminum conductors.  
Power-up  
Set the On/Stand by switch to On.  
When power is applied for the first time, the  
2
400 W (NI) @ 120 Vca  
display must show the time 00:00, the room  
temperature and the Manual mode icon ( ).  
Other information might show up on the display if  
installation is defective or does not comply with the  
instructions.  
NOTE : The On/Stand by switch set to Stand by  
will place the thermostat in sleep mode.  
Ideal for summertime.  
920-110-001-00-1-B  
1/3  
href="
For savings to be obtained, you must lower the temperature for a period of 2 to 3  
times the delay required to bring the temperature back to your comfort level.  
OPERATING MODES  
The TH110A-SP-P has two (2) operating modes.  
Example : If your system takes one hour to go from your saving temperature level  
to your comfort temperature Ievel, it is useless to lower the temperature for a  
period less than 2 to 3 hours.  
MANUAL (  
)
This mode allows you to maintain a constant temperature in the room.  
a) To Program your Schedule  
1- To activate this mode, press on Mode button to display the  
icon.  
1
- Press on PGM button to access the programming mode.  
2
- Set the desired temperature using the  
buttons or select the  
simultaneously.)  
pre-programmed  
To select the  
,
or  
settings.  
and  
2- Press on Day button to select the day to be programmed. You can select  
all days of the week by pressing on Day button for 3 seconds.  
(
setting, press on  
3- Press on PGM button to select program 1, 2, 3 or 4.  
AUTOMATIC (  
This mode executes your own programming.  
To activate this mode, press on Mode button to display the  
The or icon indicates which temperature setting is used. Also, the icon  
)
4- Press on Hour and Min buttons to program the time.  
5- When you have completed your programming, press on Mode button  
to exit this function.  
icon.  
b) To Erase a Program :  
of the program number will be shown.  
Select the program using PGM and Day buttons, and press on Clear  
button. The time field displays --:-- when the program is inactive.  
Memory back-up  
c) Example 1 : Comfort period from 7:00 AM to 10:30 PM  
Economy period from 10:30 PM to 7:00 AM  
In the event of a power failure, an internal circuit will maintain the programming  
and the time. But only the time could have to be set if power failure is more than  
Identical schedule for all days of the week.  
2
hours.  
1
2
3
- Press on PGM button to access the programming mode.  
Early Start function  
- Press on Day button 3 seconds to select every day of the week.  
The thermostat is providing a built-in function enabling it to calculate the  
optimum time to start the heating system to achieve the desired temperature  
setting at the programmed time. This function could start the heating system as  
early as 6 hours prior to the programmed time. To enable this function, set the  
switch E.S. to “ON” at the back of the thermostat.  
- Press on Hour button to enter 7:00 AM, Prog. 1 (  
).  
4- Press on PGM button again to select Prog. 2 (  
Hour and Min buttons to enter 10:30 PM.  
), and press on  
5- Press on Mode button to exit this function.  
d) Example 2 : Comfort period: Monday to Friday from 6:15 AM to  
8:15 AM and from 5:00 PM to 10:00 PM.  
PROGRAMMING  
Saturday & Sunday from 7:30 AM to 11:00 PM.  
Programming the time and day  
Schedule/Day MON.  
TUES.  
WED.  
THU.  
FRI.  
SAT.  
SUN.  
1
2
- Set the time using the Hour and Min buttons.  
- Set the day using the Day button.  
PROG. 1  
PROG. 2  
PROG. 3  
PROG. 4  
6:15 AM 6:15 AM 6:15 AM 6:15 AM 6:15 AM 7:30 AM 7:30 AM  
8
:15 AM 8:15 AM 8:15 AM 8:15 AM 8:15 AM  
---  
---  
---  
---  
Programming the Comfort, Economy and Vacation settings  
The Comfort , Economy and Vacation settings respectively represent  
the temperatures that you wish to have during the day  
5
PM  
5 PM  
5 PM  
5 PM  
5 PM  
1
0 PM  
10 PM  
10 PM  
10 PM  
10 PM  
11 PM  
11 PM  
, at night or while you  
, or while you are away for an extended period .  
are away at work  
NOTE : It is faster to program the same schedule for every day and then modify  
the exception days.  
To program your settings  
a) To program the Comfort temperature, select the desired degree using the  
buttons and press the button until the icon is displayed  
app. 3 seconds).  
b) To program the Economy temperature, select the desired degree using the  
buttons and press the button until the icon is displayed  
app. 3 seconds).  
1- Press on PGM button to access the programming mode.  
2
- Press on Day button 3 seconds to select every day of the week.  
3- Press on Hour and Min buttons to enter 6:15 AM, Prog. 1 ( ).  
) and Hour and Min buttons to  
(
4- Press on PGM button to select Prog. 2 (  
enter 8:15 AM.  
(
c) To program the Vacation temperature, select the desired degree using the  
buttons and press on the and buttons simultaneously  
icon is displayed (app. 3 seconds).  
5
- Repeat step 4 to enter Prog. 3 (5:00 PM) and Prog. 4 (10:00 PM).  
until the  
NOTE : When making modifications, make sure you are in the right  
program.  
d) Press the Mode button to exit this function and return to the normal  
operating mode.  
To modify the Saturday and Sunday schedules:  
Schedule programming  
6
-
-
Press on Day button until SA or SU is displayed.  
The TH110A-SP-P allows 4 setting changes for each day of the week. There are  
no pre-set programs.The programs are tailored to perfectly adapt to your life  
style. The principle is very simple. For each day, enter the time at which you wake  
up (P1), the time you leave for work (P2), the time you arrive back home (P3) and  
the time you go to bed (P4).  
7
Press on PGM button to select Prog. 1 (  
buttons to enter 7:30 AM.  
) and Hour and Min  
8- Press on PGM button to select Prog. 2 (  
erase it.  
) and then Clear button to  
) and then Clear button to  
) and then Hour and Min  
9-  
Press on PGM button to select Prog. 3 (  
erase it.  
Program  
Mode  
Time  
1
2
3
Wake-up time  
Departure time  
10- Press on PGM button to select Prog. 4 (  
buttons to enter 11:00 PM.  
11- Press on Mode button to exit this function.  
Return time  
Bed time  
4
920-110-001-00-1-B  
2/3  
href="
Temporary or permanent temperature bypass  
WARRANTY  
This operation allows you to temporarily modify the room temperature while you  
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY  
are in the Automatic mode. Simply press on button to select the desired  
or  
temperature, or the or button to select the Comfort or Econo settings you  
have programmed.This temperature will be maintained until the beginning of the  
next programmed schedule.  
This product is warranted against material defects and workmanship in normal  
use for a period of one year, from the date of the original purchase from  
authorized dealers. During this period, AUBE technologies inc. will repair or  
replace the product with a new or of equivalent quality at AUBE'S option, without  
charge, any product proven defective in normal use.  
You can also switch to the Vacation setting for a prolonged absence by pressing  
on  
and  
at the same time.The display will show  
icon. In that case,  
the derogation is permanent. To return to the normal operating mode, press on  
Mode button.  
Warranty does not cover transportation costs. Nor does it cover a product  
subjected to misuse or accidental damage. This warranty does not cover the cost  
of installation, removal or reinstallation.  
If you wish to immediately return to the programmed settings, press on Mode  
button twice.  
This limited warranty is in lieu of all other warranties, obligations or liabilities  
expressed or implied by the company. In no event shall AUBE technologies inc.  
be liable for consequential or incidental damages resulting from installation of this  
product. Some states or provinces do not allow limitations on how long an implied  
warranty lasts, or the exclusion or limitation of incidental or consequential  
damages, so the above exclusions or limitations may not apply to you. This  
warranty gives you specific legal rights and you may also have other rights which  
vary from state to state.  
CHARACTERISTICS  
Model:  
TH110A-SP-P (120 VAC)  
120 VAC, 50/60 Hz  
20 A maximum (resistive only)  
2400 watts (NI) @ 120 VAC  
CSA / UL  
Supply:  
The defective product and the original sale receipt must be returned to the  
original dealer or shipped pre-paid, insured and addressed to:  
Load:  
Power:  
Aube technologies inc., 705 Montrichard, Iberville (Quebec),  
Canada, J2X 5K8  
Approvals:  
Display range:  
Setting range:  
Comfort default setting:  
Econo default setting:  
Vacation default setting:  
Storage:  
0 to 60 °C (32 to 140 °F)  
5 to 30 °C (40 to 85 °F)  
20 °C (68 °F)  
www.aubetech.com  
If you have any questions concerning the installation or programming of this  
product, please call our technical assistance at (450) 358-4600 for the Montreal  
18 °C (64 °F)  
10 °C (50 °F)  
area or 1-800-831-AUBE for outside area, Monday to Friday between  
8:30 AM and 5:00 PM Eastern time.  
-20 to 50 °C (-4 to 120 °F)  
PROBLEMS AND SOLUTIONS  
PROBLEMS  
CAUSES  
SOLUTIONS  
No display  
• Circuit breaker is open  
• Check 120 VAC presence  
at the thermostat  
Power failure  
The thermostat switch is  
in Stand by position  
• Put the switch  
in On position  
The thermostat is loosing  
the time but not the programming  
• Power failure more than  
2 hours  
Room temperature shown is wrong  
• A draft is nearby the thermostat  
• Eliminate the draft  
• Check installation  
Heating system always on  
• Bad installation  
The thermostat displays heating  
but heating system is not turned on  
• Bad installation  
• Check installation  
• Check 120 VAC presence  
at the heating system  
Programs do not change as you want  
• Incorrect programming hours  
• Check actual time  
in AM & PM as well  
as program times  
Wrong programming mode selected  
(
AM is not displayed)  
Make sure operating mode  
is set to AUTO  
01/04/02  
920-110-001-00-1-B  
3/3  

Honeywell T8621A Thermostat User Manual

Carrier PTACSTAT NP HC Thermostat User Manual

Honeywell T4098B Thermostat User Manual

Honeywell T8700C Thermostat User Manual

White Rodgers 50M56U 843 Thermostat User Manual

Honeywell 69 1815EFS 04 Thermostat User Manual

Honeywell T874A F Thermostat User Manual

Honeywell TH2210 Thermostat User Manual

Lux Products DMH100 Series Thermostat User Manual

Honeywell V4062B Thermostat User Manual