Aube TH113 R Thermostat User Manual

Home

href="
Introduction  
Control Module Installation  
Operation  
TH1 1 3-R Regulator  
User Guide  
Thank you for choosing Aube’s TH113-R Regulator.  
Align the bracket tabs on the regulator with the holes  
located on the power base.  
The TH113-R regulator operates on perpetual 15-minute  
heating cycles.  
The TH113-R is specially designed to control a floor  
heating installation, a baseboard or a convector.  
Control Module  
For example, if the dial is set  
halfway, the system will heat  
for 50% of the cycle; it will be  
ON for 7.5 minutes and OFF  
for 7.5 minutes.  
The TH113-R regulator operates like a dimmer switch to  
allow you to easily adjust the amount of power sent to  
your heating system.  
GFCI Test  
and Warning  
Light  
It features an integrated GFCI, and includes a test button  
and warning light for added security.  
Below is a detailed table of the  
cycle duration based on the  
dial’s position:  
This regulator is also equipped with an ON/STANDBY  
switch making it possible to put it in sleep mode when its  
use is not required (e.g. summer).  
On/StandBy  
Switch  
IMPORTANT!  
Position and  
equivalent %  
I
2
20%  
4
40%  
6
60%  
8
10  
0%  
80% 100%  
The GFCI and Remote Input options are not available  
with a low voltage power base. Skip sections 3 and 4.  
ON  
0 min 3 min 6 min 9 min 12 min 15 min  
15 min 12 min 9 min 6 min 3 min 0 min  
Power Base  
OFF  
Power  
Selection  
Dial  
This regulator must be installed on a PB112 power  
base.  
The screw cannot be removed completely.  
Keep the regulator’s air vents clean and free from  
obstructions.  
NOTE: Depending on the power base used, the heating  
cycles can be 15 seconds or 15 minutes.  
Technical Specifications  
GFCI Test (GA/GB line power base only)  
Remote Input (line voltage only)  
If you have any questions concerning the TH113-R  
Regulator, call our technical support team at:  
Model: TH113-R  
The GFCI monitors the electrical flow for any loss of  
current; if there is any loss, the thermostat will cut off  
power to the heating system.  
When a remote control interface (Aube CT241 or any  
other remote control system) is connected to the power  
base’s remote input and a signal is received, the TH113-R  
module automatically lowers the percentage by 35%  
based on the dial’s current position.  
Power setting range: 0 to 100%  
Storage: -20°C to 50°C (-4°F to 120°F)  
Phone:  
Montreal area:  
Canada / U.S.:  
(450) 358-4600  
We recommend you test the GFCI immediately after  
installing the control module, and once a month thereafter  
to ensure it is operating properly.  
Warranty  
1-800-831-AUBE (2823)  
(450) 358-4650  
Fax:  
The LED lights up to indicate the signal’s presence  
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED  
WARRANTY  
(
except for GA and GB models).  
Email:  
To test:  
This product is guaranteed against workmanship defects for a one  
year period following the initial date of purchase. During this period,  
AUBE Technologies Inc. will repair or replace, at our option and  
without charge, any defective product which has been used under  
normal conditions.  
n
Press the TEST button:  
Successful: TEST warning  
light is ON and power to  
The TEST button can be used to bypass the signal for a  
2-hour period.  
Monday to Friday from 8:30 AM to 5:00 PM EST.  
heating system is cut off.  
The warranty does not cover delivery costs and does not apply to  
products poorly installed or randomly damaged following installation.  
This warranty cancels and replaces any other manufacturer's  
express or implied warranty as well as any other company  
commitment.  
The LED goes off to indicate the bypass.  
Unsuccessful: TEST warning  
light is OFF.  
NOTE: When combined with a GA or GB power base, the  
TEST button is used only for GFCI testing. The  
percentage is decreased, but the bypass function and  
indicator are not available.  
For more information on our products, visit us at:  
Cut power to heating system from the main power  
panel and call customer service.  
www.aubetech.com  
AUBE Technologies Inc. cannot be held liable for related or random  
damages following the installation of this product. The defective  
product as well as the purchase invoice must be returned to the  
place of purchase or mailed, prepaid and insured, to the following  
address:  
o
When successful, reset thermostat (STANDBY/ON)  
to power heating system.  
NOTE: If the test warning light comes ON during normal  
operation, cut power to heating system from the main  
power panel and have an electrician verify the installation.  
Aube Technologies Inc.  
705 Montrichard  
Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8  
0
5/11/03 400-113-004-A  
href="
PB112-024T-15S  
Installation Instructions  
24 V Low-Voltage Power Base  
1
.
s Install the control module onto the base.  
t Apply power to the heating system.  
Applications  
n
The PB112-024T-15S power base can be used on any TH11x series  
thermostat (with the exception of the TH110 model). This low-voltage  
power base operates on 15-second cycles and can be connected to  
a line-voltage load using a solid-state relay. The PB112-024T-15S is  
compatible with most solid-state relays; however, the following Aube  
relays are optimized for use with this power base:  
u Verify the installation by checking that the heating system can be  
turned on or off using the thermostat.  
4.1  
Single SSR with Built-in Transformer  
RT850 solid-state relay (SSR)  
RT850T solid-state relay (SSR) with built-in 24-V transformer  
WARNING  
Electrical  
Panel  
Blue  
Red  
This power base MUST be used ONLY with solid-state relays. The  
use of electromechanical relays will result in reduced life expect-  
ancy and in the possibility of overheating of these devices.  
Black  
Heater  
2
.
4
.2  
Multiple SSRs with External Transformer  
Supplied Parts  
o
n One (1) power base  
o Two (2) plastic anchors  
p Two (2) mounting screws  
Electrical  
Panel  
3
.
Black  
Red  
External 24 V  
Transformer  
Installation Guidelines  
For a new installation, choose a location about 1.5 m (5 ft.)  
above the floor.  
The thermostat must be installed on an inside wall facing the  
heating system (except for floor heating systems).  
Avoid locations where there are air drafts (top of staircase, air  
outlet), dead air spots (behind a door), direct sunlight or  
concealed chimney or stove pipes (except for floor heating  
systems).  
p
Heater  
Heater  
Black  
Red  
5
.
Technical Specifications  
Maximum load: 0.5 A / 24 VAC  
r
4
.
Installation Procedure  
The installation must be carried out by an electrician and com-  
ply with local electrical codes.  
Heating cycle length: 15 seconds  
q
Operating temperature: 32°F to 122°F (0°C to 50°C)  
Storage: -4°F to 122°F (-20°C to 50°C)  
Size (H • W • D): 124 x 70 x 23 mm (4.89 x 2.76 x 0.91 in)  
Wire gauge: 14 to 22 AWG  
n Turn off power to the heating system at the main electrical panel  
to avoid electrical shock.  
o Wire the base according to your application. See typical wiring  
diagrams in sections 4.1 and 4.2.  
p For a floor heating system installation, con-  
nect the floor sensor between the S and R ter-  
minals.  
q Secure the base to the wall using the provided screws and wall  
anchors.  
r Configure the switches located on the control module (if any).  
Refer to the user guide.  
PB112-024T-15S  
400-112-024-A  
18/1/06  
1/1  

Aube TH113 AF Thermostat User Manual

Aprilaire 8620 Thermostat User Manual

White Rodgers 1F83 0471 Thermostat User Manual

Carrier 50HJQ004 016 Thermostat User Manual

Aprilaire 8535 Thermostat User Manual

Aube TH133 15S Thermostat User Manual

Aprilaire 8052 Thermostat User Manual

Honeywell T8022D Thermostat User Manual

Honeywell Y8024 Thermostat User Manual

Honeywell T8132B Thermostat User Manual