Aube TH113 Thermostat User Manual

Home

href="
Model Selection (switch)  
Temperature Lock (TH1 1 3 only)  
Setpoint Definition  
TH1 1 3 & TH1 1 6 A/ꢀ/Aꢀ  
FOR A AND AF MODELS ONLY  
At the rear of the control module is a switch that has been  
factory-set to the applicable temperature control.  
At the rear of the control module are two potentiometers.  
These potentiometers act like a temperature lock. Even  
when occupants adjust the temperature using the dial on  
the front/rear of the control module, the potentiometers  
override the dial and maintain the temperature within the  
locked-in minimum and maximum range.  
A - ambient temperature  
F & AF - floor temperature limit  
Use a flat tip screwdriver to rotate the potentiometers until  
the notch points to the desired temperature.  
Turn the dial to the desired temperature.  
TH113: The dial is located on the front of the control  
module.  
TH116: The dial is located on the rear of the control  
module.  
Owner!s Guide  
Thank you for choosing Aube’s non-  
programmable thermostat. Your new  
electronic thermostat is equipped with a  
microprocessor and proportional integral  
NOTE: The AF model can be used for all temperature  
control types (A, F and AF).  
The min. position indicates the minimum temperature  
setpoint: 45°F (7°C).  
adaptive  
(PIA)  
temperature  
control  
Note: The ambient  
sensor is not  
operational when the  
switch is set to I (up).  
technology for total comfort. Depending on  
the selected model, this thermostat has been  
designed to control:  
A: The Ambient temperature (using an  
TH116  
electric heating system)  
Public Area  
Temperature  
dial  
AF: The Ambient temperature with Floor  
temperature limit (using a floor heating  
system to heat the room)  
Potentiometers  
Notch  
F: The Floor temperature (floor heating)  
NOTE: This control module must be  
mounted on a PB112 Series power base.  
The thermostat has an On/Standby switch  
making it possible to put the thermostat in  
sleep mode when its use is no longer  
required (e.g. summer).  
TH113  
TH113  
TH116  
Warranty  
Control Module Installation  
GꢀCI Test  
Remote Input  
AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY  
Align the bracket tabs on the control module with the  
holes located on the power base.  
The GFCI monitors the electrical  
flow for any loss of current; if  
there is any loss, the thermostat  
will cut off power to the heating  
system. We recommend you test  
the GFCI immediately after  
installing the control module, and  
This product is guaranteed against workmanship defects for a one year  
period following the initial date of purchase. During this period, AUBE  
Technologies Inc. will repair or replace, at our option and without charge,  
any defective product which has been used under normal conditions. The  
warranty does not cover delivery costs and does not apply to products  
poorly installed or randomly damaged following installation. This warranty  
cancels and replaces any other manufacturer's express or implied  
warranty as well as any other company commitment. AUBE Technologies  
Inc. cannot be held liable for related or random damages following the  
installation of this product. The defective product as well as the purchase  
invoice must be returned to the place of purchase or mailed, prepaid and  
insured, to the following address:  
The TH113 and TH116 are equipped with a remote input  
which allows connection of an optional telephone  
controller (CT240) or any other remote control system.  
When a command signal is received through this input,  
the thermostat automatically lowers its setpoint by 3.5°C.  
The LED lights up to indicate the signal’s presence  
Follow the same procedure for the TH116.  
Control module  
(
except for GA and GB models).  
once  
a
month thereafter to  
Bypass (not available for GA and GB power base):  
The TEST button can be used to bypass the signal for a  
ensure it is operating properly. To  
test:  
Aube Technologies Inc.  
2
-hour period. The LED goes off to indicate the bypass.  
705 Montrichard  
!
Press the TEST button:  
NOTE: When combined with a GA/GB power base, the  
TEST button is used only for GFCI testing. The bypass  
function is not available with these power base models.  
Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8  
Successful: TEST warn-  
ing light is ON and power to heating system is cut  
off.  
If you have any questions concerning the TH113 or the TH116  
thermostat, call our technical support team at:  
Technical Specifications  
Unsucessful: The TEST warning light is OFF. Cut  
power to heating system from the main power  
panel and call customer service.  
Models: TH113 and TH116 A / AF / F  
Phone: Montreal area: (450) 358-4600  
Canada / U.S.: 1-800-831-AUBE (2823)  
Setting range: 45°F, 59°F to 95°F (7°C, 15°C to 35°C)  
Potentiometers: minimum: 41°F to 77°F (5°C to 25°C)  
maximum: 59°F to 95°F (15°C to 35°C)  
Accuracy: ± 0.9°F (0.5°C)  
Fax:  
Email:  
y(450) 358-4650  
Power base  
"
When successful, reset thermostat (STANDBY/ON)  
to power heating system.  
NOTE: Keep the thermostat's air vents clean and free  
from obstructions.  
NOTE: If the test warning light comes ON during normal  
operation, cut power to heating system from the main  
power panel and have an electrician verify the installation.  
Monday to Friday from 8:30 AM to 5:00 PM EST.  
For more information on our products, visit us at:  
www.aubetech.com  
Storage: -4°F to 120°F (-20°C to 50°C)  
NOTE: The screw cannot be removed completely.  
0
1/08/03 920-113-001-00-1-A  
href="
PB112-024T  
Installation Instructions  
24 V Low-Voltage Power Base  
1
.
4
.1  
Single SSR with Built-in Transformer  
Applications  
n
The PB112-024T power base can be used on any TH11x series  
thermostat (with the exception of the TH110 model). This low-voltage  
power base operates on 15-minute cycles and can be connected to a  
line-voltage load using a relay or directly to a 24-volt device. The  
PB112-024T is compatible with most relays; however, the following  
Aube relays are optimized for use with this power base:  
Electrical  
Panel  
Blue  
Red  
RT850 solid-state relay (SSR)  
RT850T solid-state relay (SSR) with built-in 24-V transformer  
RC840 electromechanical relay  
Black  
Heater  
RC840T electromechanical relay with built-in 24-V transformer  
4.2  
Multiple SSRs with External Transformer  
2
.
Supplied Parts  
o
Electrical  
Panel  
n One (1) power base  
o Two (2) plastic anchors  
p Two (2) mounting screws  
Black  
Red  
External 24 V  
Transformer  
3
.
Heater  
Heater  
Installation Guidelines  
For a new installation, choose a location about 1.5 m (5 ft.)  
above the floor.  
The thermostat must be installed on an inside wall facing the  
heating system (except for floor heating systems).  
Avoid locations where there are air drafts (top of staircase, air  
outlet), dead air spots (behind a door), direct sunlight or  
concealed chimney or stove pipes (except for floor heating  
systems).  
p
Black  
Red  
4
.3  
Electromechanical Relay with External Transformer  
Electrical  
Panel  
4
.
Installation Procedure  
The installation must be carried out by an electrician and com-  
ply with local electrical codes.  
q
External 24 V  
Transformer  
Heater  
n Turn off power to the heating system at the main electrical panel  
4
.4  
Hot Water Heater Valve  
to avoid electrical shock.  
Electrical  
Panel  
o Wire the base according to your application. See typical wiring  
diagrams in sections 4.1 to 4.4.  
p For a floor heating system installation, con-  
nect the floor sensor between the S and R ter-  
minals.  
Valve  
External 24 V  
Transformer  
q Secure the base to the wall using the provided  
screws and wall anchors.  
r Configure the switches located on the control module (if any).  
Refer to the user guide.  
5.  
Technical Specifications  
Maximum load: 0.5 A / 24 VAC  
r
s Install the control module onto the base.  
t Apply power to the heating system.  
Heating cycle length: 15 minutes  
u Verify the installation by checking that the heating system can be  
Operating temperature: 32°F to 122°F (0°C to 50°C)  
Storage: -4°F to 122°F (-20°C to 50°C)  
turned on or off using the thermostat.  
Size (H • W • D): 124 x 70 x 23 mm (4.89 x 2.76 x 0.91 in)  
Wire gauge: 14 to 22 AWG  
PB112-024T  
400-112-000-B  
18/1/06  
1/1  

Honeywell RTH2410 Thermostat User Manual

Honeywell T8511G Thermostat User Manual

Honeywell T87K1007 Thermostat User Manual

Lux Products DHP2120 Thermostat User Manual

Honeywell Q674L Thermostat User Manual

Honeywell T8195A Thermostat User Manual

White Rodgers 1F92W 71 Thermostat User Manual

Honeywell V8944L Thermostat User Manual

Aprilaire 8800 UNIVERSAL Thermostat User Manual

Honeywell RTH6350D1000E1 Thermostat User Manual