Aube TH134 Thermostat User Manual

Home

href="
n Time  
o Heating modes  
:Comfort mode  
Installation and User Guide  
:
Setback modes  
(
icon is steady in 3,5k setback;  
TH134 is an electronic six-order pilot-wire programmer that allows  
separate temperature control of three zones using four programs  
per day. The TH134 programmer has three pilot-wire outputs can  
be connected to thermostats or controller that accept pilot-wire sig-  
nals.  
flashes in 1k and 2k setbacks)  
Frost protection  
Off  
:
:
p Operating modes  
- Manual mode  
- Auto mode  
The TH134 programmer has a remote input to which a telephone  
controller (such as Aube’s CT240), a home automation system  
(
HAS) or an energy manager can be connected. When a signal is  
q Zone selected (the letter A  
appears when all 3 zones are  
selected)  
received from any of these devices, TH134 forwards the order to  
the heating units.  
r Current program (applicable to  
automatic mode only)  
n Order buttons  
r Program button  
s Return button  
t Selection button  
u Display  
o Mode selection button  
p Zone selection button  
q Time/day setting button  
The following table shows the different means of initiating an order.  
Maintain temperature at setpoint (Comfort)  
No signal  
Maintain temperature at setpoint minus 3,5°C (3,5k setback)  
Maintain temperature at 7°C (frost protection)  
Turn heating Off (Off)  
Maintain temperature at setpoint minus 1°C (1k setback)  
Maintain temperature at setpoint minus 2°C (2k setback)  
TH134  
400-134-000-A  
1/27/05  
1/4  
href="
I nstallation  
P
                                                                              
o
                                                                                 
w
                                                                                    
e
                                                                                       
r
                                                                                          
-
                                                                                           
u
                                                                                             
p
                                                                                               
During power-up, the TH134 perform a series of test for approxi-  
mately 5 seconds. Afterwards, the programmer displays the follow-  
ing:  
The installation must be performed by an electrician. The program-  
mer must be installed on an electrical box.  
All three zones  
Flashes to indicate  
are in comfort  
that the time and day  
mode.  
must be set.  
n Loosen the locking screw (the  
screw is captive and cannot be  
completely removed).  
Zone 1 is selected.  
The programmer is  
in manual mode.  
o Pull and lift the bottom of the  
faceplate to remove it from its  
mounting plate.  
n Press . The hours display flashes.  
Connect power to terminals L (line) and N  
o Set the hours using the  
p Press . The minutes display flashes.  
q Set the minutes using the buttons.  
r Press . The day display flashes.  
s Set the day using the buttons.  
t Press to exit the time and day settings  
buttons.  
(
neutral).  
Connect the pilot wire inputs of the thermo-  
stats to terminals FP1, FP2 and FP3.  
The terminals accept wire thick-  
nesses between 0,32 and 2,1 mm2.  
Operation  
Connect terminals 2 and 1 of the CT240 to terminals L and TEL of  
the programmer respectively.  
.If the “setback” and “off’ orders received by a heating unit  
are reversed, reverse the “Ph” and the “N” wires on the heating unit.  
Connect the terminals of one of the outputs of CT241 to terminals L  
and TEL of the programmer .  
Transmits the order selected via one of the  
order buttons. To use this mode:  
Connect the normally-open relay of the home automation system  
terminals L and TEL of the programmer.  
n Select the zone by pressing the Zone but-  
ton. (Press for 3 seconds to select all 3  
zones.)  
Connect the pilot wire output of the energy manager to the TEL  
input of the programmer.  
o Select the manual (Man) mode by press-  
ing the Man/Auto button.  
p Select the order by pressing the  
appropriate order button.  
n Fix the mounting plate to the wall.  
o Install the faceplate on the mounting plate and lock them  
together using the locking screw.  
The orders are sent to each zone according to  
the schedule programmed for that zone. To  
use this mode:  
n Select the zone by pressing the Zone but-  
ton. (Press for 3 seconds to select all 3  
zones.)  
o Select the Auto mode by pressing the  
Man/Auto button.  
You can bypass the automatic mode for 2 hours. At the end of the 2  
hours, the programmer returns to the automatic mode.  
n Select the zone using the Zone button. (Press for  
3
seconds to select all 3 zones.)  
o Press the desired order button.  
The auto mode icon flashes during the bypass.  
TH134  
400-134-000-A  
1/27/05  
2/4  
href="
o Select the zone using the Zone button. (Press for 3  
seconds to select all 3 zones.)  
Whenever an order is received via the remote input, it becomes the  
active order for all 3 zones. To know which orders can be initiated  
by the energy manager, the phone controller or the home automa-  
p Select the program using the PGM button.  
q Set the program start time.  
tion system, see the table on page 1. The  
signals are received via the remote input.  
is displayed when  
r Select the mode by pressing the corresponding button.  
s Repeat steps 3 to 5 for the remaining programs for the selected  
zone.  
Orders received via the remote input have priority over orders initi-  
ated via the TH134 programmer. However, you can bypass the  
remote input order for each zone for 2 hours. At the end of the 2  
hours, the remote input order becomes active again.  
t Go to step 2 if you wish to select another zone.  
u Press  
to exit programming.  
TH134 will automatically exit programming if no button is  
pressed for the last 60 seconds.  
n Select the zone using the Zone button. (Press for 3  
seconds to select all 3 zones.)  
When selecting the number of programs,  
o Press the desired order button.  
n Press the MAN/AUTO button for 3 seconds  
The  
icon flashes during the bypass.  
until PPd is displayed.  
o Select the zone using the ZONE button.  
(
Press for 3 sec. to select all 3 zones.)  
Preprogrammed Schedule  
p Press MAN/AUTO until the desired day is  
The same schedule is used by default for all 3 zones as shown  
below.  
displayed.  
q
Set the number of programs for the selected  
day using the buttons. The options are:  
4 (to select all 4 programs)  
2 (to select program 1 and 4 only)  
0 (no program is selected for that day)  
If no program is selected for a particular day, TH134 uses  
the order of the last program until the start of the next program.  
r Repeat steps 3 and 4 for the each remaining day.  
s Go to step 2 if you wish to select another zone.  
Wake-up time  
Leave for work  
Return home  
Sleep time  
t Press  
to exit.  
Enter your settings in the following table.  
Every day  
Monday to  
Friday  
Monday to  
Friday  
Every day  
C
S
C
S
4
4
4
4
4
2
2
Schedule customization  
Use the following procedure to select the order and the start time for  
each of the 4 programs for each zone. The settings of each pro-  
gram will be the same for each day. However, you can then select  
which programs to be executed for each day and for each zone.  
n Press the PGM to start programming.  
TH134  
400-134-000-A  
1/27/05  
3/4  
href="
Technical S  
                             
                             
p
                                
e
                                  
c
                                     
i
                                       
f
                                        
i
                                         
c
                                          
a
                                             
t
                                               
i
                                                 
o
                                                  
n
                                                    
s
                                                       
:
TH134  
:
230 VCA / 50 Hz  
25 mA maximum  
:
:
60 mA per output / 230 VCA  
10 units per pilot wire output (FP)  
0 - 50°C  
-20 - 50°C  
:
:
:
:
class 2  
:
IP20  
:
1Y type  
:
normally polluted  
:
class A  
:
:
program settings are permanently saved  
time settings are saved for 4 hours during power  
outage  
universal relay (230 VCA / 500 µA) or pilot wire  
:
0,32 - 2,1 mm2.  
Warranty  
AUBE TECHNOLOGIES INC. THREE (3) YEAR LIMITED WARRANTY  
This product is guaranteed against workmanship defects for a  
three-year period following the initial date of purchase. During this  
period, AUBE Technologies Inc. will repair or replace, at our option  
and without charge, any defective product which has been used  
under normal conditions.  
The warranty does not cover delivery costs and does not apply to  
products poorly installed or randomly damaged following installa-  
tion. This warranty cancels and replaces any other manufacturer's  
express or implied warranty as well as any other company commit-  
ment. AUBE Technologies Inc. cannot be held liable for related or  
random damages following the installation of this product.  
The defective product as well as the purchase invoice must be  
returned to the place of purchase or mailed, prepaid and insured, to  
the following address.  
Technical Support  
For any questions regarding the product installation or operation,  
contact our technical support team at:  
705, Montrichard  
Saint-Jean-sur-Richelieu, Québec  
J2X 5K8  
Canada  
Tel. : (450) 358-4600  
1-800-831-AUBE  
10, rue Ampère  
95500 Gonesse, France  
Tel. : 33 (0) 1 34 07 99 00  
Fax : 33 (0) 1 34 07 99 19  
TH134  
400-134-000-A  
1/27/05  
4/4  

Honeywell T694B Thermostat User Manual

Honeywell V4944 Thermostat User Manual

Honeywell RM7800E,G,L,M; RM7840E,G,L,M Thermostat User Manual

Honeywell Q674F Thermostat User Manual

Honeywell T8090A Thermostat User Manual

Trane TAYSTAT 540 Thermostat User Manual

Honeywell TH3110D Thermostat User Manual

White Rodgers 1F85 0471 Thermostat User Manual

White Rodgers 1F97 71 Thermostat User Manual

Hunter Fan 40050 Thermostat User Manual