Aube TH140 28 Thermostat User Manual

Home

TH140-28

Installation and User Guide

Electronic Programmable Thermostat

.2 Thermostat Wiring

Installation

NORTH AMERICA

.1 Guidelines

LOW VOLTAGE < 30 V: no polarity

TURN OFF POWER TO THE HEATING SYSTEM AT THE MAIN

POWER PANEL TO AVOID ELECTRICAL SHOCK.

Installation should be carried out by an electrician.

20/240 V

•

For a new installation, choose a location about 5 ft. (1.5 m) above

the floor.

Connection to a

circulatorthrough

a 24 V relay

The thermostat must be installed facing the heating system and on

an inside wall.

Relay

Avoid locations where there are air drafts (top of staircase, air out-

let), dead air spots (behind a door), direct sunlight or concealed

chimneys or stove pipes.

24 V transformer

Relay

Connection to the

thermostat terminals

of a furnace

Furnace

LINE VOLTAGE 120 to 240 VAC

Must be installed onto a certified electrical box.

Power supply

A maximum load

20/240 V

Connection to a

circulator (pump)

Load

n Loosen the captive screw holding the faceplate to the mounting

of a water heating

system

Provided wires

plate.

o Pull the lower part of the faceplate to remove it from the mount-

ing plate.

EUROPE

p Loosen the screw (captive) holding the wire cover and remove

For a 2-wire connection: no polarity

the wire cover.

q Pull wires through the hole in the mounting plate and secure the

mounting plate to the wall (or onto an electrical box for line volt-

age wiring) using the enclosed wall anchors and screws.

Direct wiring to

the circulator

240 V

r Wire the thermostat to the heating system (see section 1.2) and,

if necessary, connect the remote input (see section 1.3).

s Once wiring is complete, re-install the wire cover.

t Use the switches located at the back of the faceplate to config-

ure your thermostat (see section 1.4) according to your applica-

tion.

Relay

Connection to the

thermostat terminals

of a furnace

Furnace

u Install the batteries (see section 1.5).

v Mount the faceplate on the mounting plate and tighten the screw.

For a 3-wire connection: observe the polarity

Wiring to a

power-operated

mixing control valve

40 V

TH140-28

400-140-000-C

2008-01-15

1/4

.3 Remote Input Wiring

Heating Cycle Selection (switches #1 and #2)

The TH140 is equipped with a remote input which allows connection

of a telephone controller (optional Aube CT240), a home automation

system or any other remote control system. When a signal is

received through this input, the TH140 will automatically switch from

normal operating mode to Vacation mode, or vice versa when the sig-

nal is removed.

Select the cycle using switches #1 and #2. Short cycles help

eliminate temperature variations, thus increasing user comfort. Since

shorter cycles can lead to premature system wear, it is important to

select the temperature control cycles appropriate to your heating

system. In general, the bigger your heating unit is, the longer the

cycles should be.

.3.1 Connection to the CT240

Cycles

EUROPE

AMERICA

Position

Connect CT240 terminals A and C to TH140

terminals X and C. You must respect the

polarity.

Not recommended for Not recommended for

minutes

furnaces

central units

For details on operating the telephone control-

ler, refer to the instruction manual.

Gas or electric

wall furnace

Radiant or convection

electric heating

10 minutes

15 minutes

.3.2 Connection to a home automation system

Fuel or gas floor

furnace, forced air

heating

Connect the TH140 to the home auto-

mation system as displayed in the wir-

ing diagram.

Home automation system

Central heating

0 minutes

Commercial unit

1.4 Configure the Thermostat

.4.2 Conventional mode with anticipation (switch #5)

The switches are located on the back of the faceplate. Default set-

tings are highlighted.

This mode is compatible with all heating systems.

Programmable Span Selection (switches #1 and #2)

Switch

Description

15 min (see 1.4.1)

0.5°C (0.9°F) (see 1.4.2)

DOWN

Select the span using switches #1 and #2. The default temperature

span is 0.5°C (0.9°F). For example, if the temperature setpoint is

20°C (68°F), the heating system will turn on at 19.5°C (67.1°F) and

turn off at 20.5°C (68.9°F).

Cycles (proportional)

Span (conventional)

Clock display

& 2

12H

°F

24H

°C

Temperature display ¹

Span

Hot Water Heating

Forced Air Heating

Position

Proportional

Conventional

(see 1.4.2)

Temperature control mode

(

see 1.4.1)

0,3°C

Not recommended for Not recommended for

Pump protection ²

Deactivate

Activate

(0,5°F)

furnaces

central units

If you change from °C to °F (or vice versa), you will need to reprogram

your Comfort, Economy and Vacation settings.

For hot water installations, it is recommended to enable this option to acti-

vate the pump for one minute every 24 hours to prevent pump seizure.

,4°C

Gas or electric

wall furnace

Radiant or convection

electric heating ¹

(0,7°F)

,5°C

Fuel or gas floor

furnace

Central heating

.4.1 Proportional Adaptive Mode (switch #5)

(0,9°F)

This mode analyzes previous cycles to define the the next duty cycle.

This control mode guarantees optimal temperature control based on

the system’s capacity. To extend the life of the system, a minimum

On/Off time of 10% of the cycle has been implemented. For example

with a 15-minute cycle, the system would not start or stop for less

than 1.5 minutes.

0,6°C

(1,1°F)

Commercial unit

1. 240 volt heating with relay (baseboard, convector, radiant ceiling, etc.)

Ideal for:

•

Radiant or convection electrical heating system

Circulator control in a hot water system

Electrical hot-air furnace

Conventional gas or fuel hot-air furnace

Not recommended for:

•

Gas or fuel furnace or boiler with a wall chimney having a 30-sec-

ond or higher combustion gas purging cycle. To figure out the gas

purging cycle of your system, count the time between the heating

command sent by the thermostat and the moment when the

burner actually goes on.

•

Multi-zone systems, where several thermostats command a single

heating unit.

Note: In these last two cases, conventional mode with anticipation is

recommended.

TH140-28

400-140-000-C

2008-01-15

2/4

.5 Install the Batteries

Select the Operating Mode

When you first install the batteries, the unit runs a

sequence of tests and a complete reset to zero. The

The TH140 offers three operating modes:

screen should display 0:00 MO

and the ambient tem-

perature. The current setpoint is 20°C.

3.1 Automatic

The ambient temperature could be higher if you are holding

the TH140 in your hands. It will return to normal about one

hour after installation.

This mode executes the schedule. To activate:

•

Press Manual/Auto until

is displayed. The program

setpoint icon is displayed.

.5.1 Replacing the batteries

.1.1 Temporary Bypass

The TH140 will display an icon indicating that

the batteries must be replaced. This icon will be

displayed for 60 days; after this delay, the

TH140 will shut down the heating unit.

When in Automatic mode, you can temporarily bypass the

current program setpoint until the beginning of the next program. To

bypass:

The time and programming are saved for

•

Set the desired temperature

use a pre-defined setpoint.

OR quickly press

15 seconds when replacing the batteries.

.2 Manual

Basic Configuration

Note: You may program the thermostat while holding it in your hands

This mode allows you to maintain a constant temperature.

To activate this mode:

or when it is mounted on the mounting plate.

•

Press Manual/Auto until

is displayed.

.1 Set the Time and Day

Set temperature

OR quickly press

to use

n Set the time, using the Hour and Minute buttons.

o Set the day, using the Day button.

a pre-defined setpoint.

.3 Vacation

Maintains a specific temperature when away for a pro-

longed absence (e.g. vacation).

.2 Configure the Setpoints

.2.1 Comfort and Economy

•

From the TH140, quickly press

to activate.

These setpoints are associated to the schedule’s programs and are

pre-programmed as follows:

Can also be activated remotely (CT240, home automa-

tion system or any other system) if the remote input is

connected to one of these systems.

Comfort

20°C (68°F)

18°C (64°F)

Programs 1 and 3

Programs 2 and 4

Note: When the Vacation mode is activated remotely, it can only be

Economy

deactivated remotely.

Note: For details on how to activate the Vacation mode using a tele-

.2.2 Vacation

phone, refer to the CT240 Instruction Manual.

This pre-programmed setpoint is used when the Vacation mode is

activated.

Program Your Schedule

Vacation

10°C (50°F)

The TH140 allows four setting changes for each day of the week.

There are no pre-set programs. Your heating system switches betw-

wen the Comfort setpoint and the Economy setpoint according to the

times you would have set.

.2.3 To Modify a Setpoint

n Set the temperature using

o Press and hold one of the setpoint

buttons ( or or ) until the

icon is displayed on the screen

approx. 3 seconds).

For example, enter each day the time at which you wake up

(PROG 1), the time you leave for work (PROG 2), the time you return

home (PROG 3) and the time you go to bed (PROG 4):

(

Programs

PROG 1

PROG 2

PROG 3

PROG 4

Associated Setpoint

Time

Wake-up

Leave

.3 View the Current Setpoint

(Comfort)

To view the current setpoint, quickly press

once one of the arrow buttons

(

Economy)

Return

Sleep

(Comfort)

The screen displays the setpoint; the arrow

indicates a setpoint.

(

Economy)

Note: For temperature increases (PROG 1 and 3), allow at least

5 minutes per 1°C (2°F). For example, if you have lowered

the temperature by 3°C (6°F) while you sleep and you wake up

at 7 a.m., change the setting at 6:15 a.m.

TH140-28

400-140-000-C

2008-01-15

3/4

.1 Set or Modify the Programs

Technical Specifications

•

After 60 seconds of inactivity, the thermostat will automatically exit

programming mode.

Power supply: 2 AA or LR6 alkaline batteries 1.5 V

Max. resistive load: 5 A @ 240 VAC / 5 A @ 30 VDC

Max. inductive load: 2 A @ 240 VAC / 2 A @ 30 VDC (P.F. = 0.4)

Remote input: 12 VDC, ± 10%, 2.5 mA

Certifications: CE, c UL us

•

It is sometimes faster to program the same schedule for the entire

week and then modify the exception days.

n Press Program. The screen displays MO and PROG 1.

o Press Day to select the day (hold for 3 seconds to select all days

Control device: Electronic

of the week).

Automatic action: Type 1 B

p Press Hour and Minute to set the start time.

To clear an entry, press Clear, the time zone displays --:-- when

the program is inactive.

Number of programs: 4 programs / day, total of 28 programs

Storage temperature: -20°C to 50°C (-4°F to 122°F)

Operating temperature: 0°C to 50°C (32°F to 122°F), 95% R.H.

Temperature setting range: 5°C to 30°C (40°F to 85°F)

Temperature display resolution: 0.1 degree

Temperature reading accuracy: ± 0.5°C (± 0.9°F)

Software: Class A

q Press Program to select the program number (2, 3 or 4).

r Repeat steps 3 and 4 for remaining programs.

s Press Manual/Auto to exit.

.1.1 Programming Example

Protection class: II

Comfort (programs 1 and 3):

Protection degree: IP 40

•

Monday to Friday between 6:00 a.m. and 8:30 a.m. and

between 4:00 p.m. and 11:00 p.m.

The terminals are designed to handle a cross-section of wire measur-

ing up to 2.5 mm (14 AWG).

•

Saturday and Sunday between 6:00 a.m. and 11:00 p.m.

Economy (programs 2 and 4):

Warranty

;

•

Monday to Friday between 8:30 a.m. and 4:00 p.m. and

between 11:00 p.m. and 6:00 a.m.

Aube warrants this product, excluding battery (if applicable), to be free from defects in the

workmanship or materials, under normal use and service, for a period of three (3) years

from the date of purchase by the consumer. If at any time during the warranty period the

product is determined to be defective or malfunctions, Aube shall repair or replace it (at

Aube's option).

•

Saturday and Sunday between 11:00 p.m. and 6:00 a.m.

PROG

MON

6:00

8:30

TUE

6:00

8:30

WED

6:00

8:30

THU

6:00

8:30

FRI

6:00

8:30

SAT

6:00

--:--

SUN

6:00

--:--

If the product is defective,

(

return it, with a bill of sale or other dated proof of purchase, to the place from which

you purchased it, or

ii) contact Aube. Aube will make the determination whether the product should be

returned, or whether a replacement product can be sent to you.

This warranty does not cover removal or reinstallation costs. This warranty shall not

apply if it is shown by Aube that the defect or malfunction was caused by damage which

occurred while the product was in the possession of a consumer.

Aube's sole responsibility shall be to repair or replace the product within the terms stated

above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,

INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING,

DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS

OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some provinces and

states do not allow the exclusion or limitation of incidental or consequential damages, so

this limitation may not apply to you.

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS

PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WAR-

RANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS

HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some

provinces and states do not allow limitations on how long an implied warranty lasts, so

the above limitation may not apply to you.

4:00

--:--

11:00

To program this schedule:

n Press Program. The screen displays MO and PROG 1.

o Press and hold Day for 3 seconds to select all days of the week

(MOTUWETHFRSASU).

p Set the time (6:00) for the first program (PROG 1) using the

Hour and Minute buttons.

q Press Program to select PROG 2. Set the time (8:30) using the

Hour and Minute buttons.

This warranty gives you specific legal rights, and you may have other rights which vary

from province or state to another.

r Press Program to select PROG 3. Set the time (4:00 p.m.) using

the Hour and Minute buttons.

ꢀ ^T^e^c^hⁿⁱ^c^a^l^A^s^sⁱ^s^t^aⁿ^c^e

s Press Program to select PROG 4. Set the time (11:00 p.m.)

using the Hour and Minute buttons.

t Press Manual/Auto to exit.

705 Montrichard

Saint-Jean-sur-Richelieu

Québec, Canada J2X 5K8

10 rue Ampère

95500 Gonesse

France

To erase programs 2 and 3 for Saturday and Sunday:

n Press Program to access programming mode.

o Press Program until PROG 2 is selected.

p Press Day to select SAturday (SA).

q Press Clear to erase the time (--:--).

r Press Day to select SUnday (SU).

s Press Clear to erase the time (--:--).

t Repeat steps 2 to 5 for PROG 3.

u Press Manual/Auto to exit.

Tel. : (450) 358-4600

33 (0) 1 34 07 99 00

33 (0) 1 34 07 99 19

advaube@comintes.com

-800-831-AUBE

Fax : (450) 358-4650

aube.service@honeywell.com

For more information on our products, visit us at

www.aubetech.com

TH140-28

400-140-000-C

2008-01-15

4/4

Honeywell T775A Thermostat User Manual

Honeywell TB7220U Thermostat User Manual

Honeywell RLV450 Thermostat User Manual

Lux Products ELV1PSPLV510 Thermostat User Manual

Honeywell T6380 Thermostat User Manual

Honeywell RTH221B1021E1 Thermostat User Manual

Honeywell T87F Thermostat User Manual

Hunter Fan 40352 Thermostat User Manual

Honeywell T4039C Thermostat User Manual

Honeywell TH8110U1003 Thermostat User Manual