Aube TH147 P Thermostat User Manual

Home

TH147-P & TH148LE-P 2. Installation

Programmable Thermostats

Note: The installation must be performed by an electrician or a qual-

ified installer.

Installation

and User Guide 2.1 Removing the Old Thermostat

IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT

. Introduction

POWER TO THE HEATING/COOLING SYSTEM.

n Remove the old thermostat to access the wires.

The TH147-P and TH148LE-P programmable thermostats can be

used to control:

Attention: If the old thermostat was mounted onto an electrical box,

it might have been powered by 120/240 volts. In this case, the

TH147-P or TH148LE-P thermostat cannot be used.

•

a gas, fuel oil or electric furnace - 2 or 3 wires

a central air conditioner - 2 or 3 wires

o Identify and label each wire (with the corresponding letter on

a hot water system with or without pump - 2 wires

a millivolt system - 2 wires

the wire terminal) and remove them from the terminals.

p If necessary, strip the end of each wire

a central heating and cooling system - 4 or 5 wires

(

maximum of 6 mm).

Attention: These thermostats are not compatible with heat pumps

or multi-stage systems.

q Wrap the wires around a pencil to prevent

them from falling into the wall.

r If the hole in the wall is too big, insulate it

using a non-flammable material in order to

avoid air draughts behind the thermostat.

Adjustment

Display

buttons

2.2 Installing the New Baseplate

Backlight

button

For a new installation, choose a location approximately 1.5 m

5 feet) above the floor and on an inside wall. Avoid draughty

(

areas (top of staircase, air outlet, etc), dead air spots (behind

doors), direct sunlight or areas near concealed pipes or chim-

neys.

System operating

mode selector

Fan operating

mode selector

Programming

buttons

Functions

Heating/cooling control

Fan control

n Remove the thermostat faceplate.

o Loosen the locking screw in order to separate the thermostat

-day programming including:

from its baseplate (the screw cannot be completely removed).

Pre-programmed energy-saving schedule

Early Start

Temporary bypass

Time display (12 h or 24 h)

Programmable cycle lengths

Temperature display in °C or °F

Backlit display

Battery replacement indicator

Filter replacement indicator

Unoccupied mode activated remotely (requires Aube’s CT240)

Interchangeable faceplates (titanium, charcoal & taupe)

Automatic daylight savings changeover

p Gently tilt the thermostat upwards.

q Mark and bore the appropriate mounting holes (or use the

existing holes). Insert the plastic anchors.

r Pass the wires through the opening of the baseplate and fix the

baseplate to the wall using the screws provided.

TH147-P and TH148LE-P

400-147-000-D 18/4/06 1/5

.3 Connecting the Thermostat

2.3.5 4-wire Heating and Cooling

Refer to the following table for matching the wire labels with the

thermostat terminals.

Terminals

Description

Heating power supply

Wire labels

Rh, R, 4, V

Rc, R

Heat relay

Cool relay

Cooling power supply

Heating signal

Cooling signal

Fan

W, W1, H

Y, Y1, M

G, F

Fan relay

Un / Un Input for a remote control device (TH148LE-P only)

.3.6 5-wire Heating and Cooling

Note: Do not connect wires identified as C, X or B. Wrap the bare

end of these wires with electrical tape.

n Loosen the screws of the terminal

block and insert the wires in the

respective terminals.

Fan relay

o Tighten the screws.

Heat relay

Cool relay

Important: The red jumper wire between

Rh and Rc terminals must be removed in a

Note: Remove the red jumper wire between terminals Rc and Rh.

-wire installation.

.3.1 2-wire Heating

2.4 Remote Control Input (TH148LE-P only)

The TH148LE-P thermostat has an input to which a CT240 tele-

phone controller (optional) or any other remote control system (e.g.,

home automation) can be connected. When the input receives a

12-VDC signal, the thermostat switches from its current mode to the

unoccupied mode and vice versa when the signal is removed.

Heat relay

Cool relay

Heat relay

The unoccupied mode can be used to re-adjust the temperature to

save energy when you are away for an extended period of time. To

set the unoccupied mode temperature, see section 4.

.3.2 2-wire Cooling

.4.1 Connecting to CT240

Connect TH148LE-P terminals UN and UN to

CT240 terminals A and C (no polarity to observe).

.4.2 Connecting to a Home Automation System

Connect TH148LE-P terminals UN and UN to a

2-VDC circuit as shown.

.3.3 3-wire Heating

2.5 Setting JP2 Jumper

Fan relay

The jumper specifies how the fan will operate when it is placed in

automatic mode.

.3.4 3-wire Cooling

Leave the jumper in this position if you

have a gas or fuel oil furnace.

JP2 jumper

Place the jumper in this position if you

have an electric furnace.

Cool relay

Fan relay

TH147-P and TH148LE-P

400-147-000-D 18/4/06 2/5

.6 Installing the Batteries

3.3 Viewing and Setting the Temperature

The ambient temperature is normally displayed. To view the set-

point, press once on one of the

buttons. The setpoint is dis-

played for 5 seconds and is indicated by the

display. During the setpoint display, press one of the

change it.

symbol on the

buttons to

.4 Backlight

The display illuminates for 12 seconds when the backlight button or

either of the buttons is pressed.

n Gently pull out the battery cover.

o Install the batteries as shown. Observe the polarity.

p Reinstall the battery cover. You will hear a clicking sound.

After the batteries are installed, the thermostat performs a

sequence of tests for approximately 5 seconds.

.5 Thermostat Control Mode

.5.1 Manual

The setpoint must be set manually. To place the thermostat in this

mode, press [ Mode ]. The house icon will disappear.

Afterwards, the thermostat displays the measured temperature. It is

normal that the displayed temperature be higher than the ambient

temperature if you hold the thermostat in your hands. Once installed

on the wall, the thermostat will display the ambient temperature. By

default, the setpoint is 21°C (70°F) and the operating mode is set on

manual.

.5.2 Automatic

The setpoint varies according to the programmed schedule. To

place the thermostat in this mode, press [ Mode ]. The current

period settings will be displayed. The four possible periods are:

The time and day settings flash to indicate that they must be set

(see section 5.1).

Wake up

Leave for work

Return home

Sleep

.7 Completing the Installation

To see the default schedule settings, see section 5.3.

.5.3 Unoccupied (TH148LE-P only)

To place the thermostat in unoccupied mode, see section 2.4. In this

mode, the

icon is displayed and only the

buttons work to

allow a temporary bypass.

.6 Temporary Bypass

.6.1 Automatic Mode

If you modify the setpoint (using the

buttons) when the thermo-

n Once the baseplate and the batteries are installed, mount the

stat is in automatic mode, the thermostat temporarily bypasses the

current program. The new setpoint will be maintained for 2 hours,

then the thermostat will return to the program currently running in

automatic mode. The house icon flashes during the bypass.

thermostat on the baseplate.

o Secure the thermostat using the locking screw and install the

faceplate.

p Apply power back to the system.

3.6.2 Unoccupied Mode (TH148LE-P only)

If you modify the setpoint (using the

buttons) when the thermo-

stat is in unoccupied mode, the thermostat temporarily bypasses

the setpoint of the unoccupied mode. The new setpoint will be main-

tained for 2 hours, then the thermostat will return to the setpoint of

. Basic Functions

.1 System Operating Mode

the unoccupied mode. The

icon flashes during the bypass.

Use this selector switch to set the system to heating

mode (HEAT), cooling mode (COOL), or Off.

3.7 Filter Indicator

Note: When you place the thermostat in cooling mode,

you might need to wait up to five minutes before cooling can start.

After 500 hours of operation, an icon appears to indi-

cate that the filter needs replacement. Once the filter

is replaced, press [ Filter ] for 3 seconds to remove

This delay is a safety feature for the compressor.

screen until cooling can start again.

will flash on the

the icon and reset the counter.

.2 Fan Operating Mode

3.8 Battery Indicator

Use the selector switch to set the fan to automatic

mode (AUTO) or continuous mode (ON).

An icon appears when the batteries need replacement.

This icon will flash for 120 days, then the thermostat

will cut power to the heating/cooling unit. The icon dis-

appears once the batteries are replaced and the ther-

mostat reinstalled on its base.

Note: This switch is not used in a 2-wire installation as

the fan is not connected to the thermostat.

AUTO The fan operates only when heating or cooling is activated.

Warning: Before removing the batteries, place the

system switch on the thermostat to Off. Otherwise, the

heating/cooling unit might still be running even after

the batteries are removed.

The fan operates continuously.

TH147-P and TH148LE-P

400-147-000-D 18/4/06 3/5

After replacing the batteries, set the time and day (see section 5.1).

For TH148LE-P model, set the date also (see section 5.2).

5.2 Setting the Date (TH148LE-P model only)

The date must be needed for the daylight-savings changeover func-

tion.

Note: The temperature and schedule settings are not erased when

the batteries are removed.

n Press [ Clk ] for 3 seconds to display the year.

. Configuration Menu

o Set the year using

and press [ Clk ] to dis-

play the month.

DISPLAY

DESCRIPTION

Temperature display

DEFAULT

°C

OPTIONS

°C or °F

p Set the month using

play the date.

q Set the date using

r Press [ Exit ] to exit.

Time display

Early Start ¹

12 h

12 h or 24 h

On or Off

Off

.3 Pre-programmed Schedule

Automatic daylight savings

_c_h_a_n_g_e_o_v_e_r₍_T_H₁₄₈_L_E_-_P_o_n_l_y₎2

Off

On or Off

When set in automatic mode, the thermostat follows the pro-

grammed schedule. You can program up to 4 periods per day. To

program a period, you must set its start time, its heating setpoint

and its cooling setpoint. You can have a different program for each

day of the week.

Unoccupied mode setpoint - heat-

_i_n_g₍_T_H₁₄₈_L_E_-_P_o_n_l_y₎₃, 4

10°C

(50°F)

5°C to 28°C

(41°F to 82°F)

Unoccupied mode setpoint - cool-

ing (TH148LE-P only) ³^,⁴

35°C

(95°F)

15°C to 35°C

(59°F to 95°F)

Your thermostat is pre-programmed with the following schedule.

Heating cycles per hour ⁴

Cooling cycles per hour ⁴

2, 3, 4, 5 or 6 ⁵

2, 3, 4, 5 or 6 ⁶

Pre-programmed settings

MO TU WE TH FR SA SU

When Early Start is enabled (On), the thermostat determines when heating or

Heating

21°C (70°F)

cooling should start so the desired temperature is reached at the set time.

6:00 a.m.

When this function is On, the thermostat automatically switches to daylight sav-

ings time on the second Sunday of March and to normal time on the first Sunday of

November (see section 5.2).

Cooling 25.5°C (78°F)

Heating 16.5°C (62°F)

Cooling 29.5°C (85°F)

To enable the unoccupied mode, see section 2.4.

8:00 a.m.

6:00 p.m.

When either the heating or cooling parameter is displayed, use the Heat/Cool

selector switch to alternate between the two parameters.

Heating

21°C (70°F)

For optimal heating control, use the setting that matches your system as follows:

=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace),

=15 min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).

Cooling 25.5°C (78°F)

Heating 16.5°C (62°F)

The corresponding cycle lengths are: 2=30 min., 3=20 min., 4=15 min., 5=12 min.,

=10 min.

0.00 p.m.

Cooling

28°C (82°F)

In the pre-programmed schedule, all 4 periods are used for Monday

through Friday and only periods 1 and 4 are used for Saturday and

Sunday.

n To access the configuration menu, press the backlight button

for 3 seconds.

o To go to the next parameter (menu item), briefly press the back-

.4 Customizing the Schedule

light button.

p To modify a parameter, press

Use the following grid to record your new settings.

q Repeat steps 2 and 3 if necessary.

Program days

Periods Settings

r Press the backlight button for 3 seconds to exit the configura-

tion menu.

Time

Heating

Cooling

Time

. Programming

.1 Setting the Time and Day

Heating

Cooling

Time

n Press [ Clk ]. The hour flashes.

Heating

Cooling

Time

o Set the hour using

p Press [ Clk ]. The minutes flash.

q Set the minutes using

r Press [ Clk ]. The day flashes.

Heating

Cooling

•

Press [ Pgm ] to enter the programming mode. The settings for

Monday, Period 1 appear.

s Set the day using

t Press [ Exit ] to exit.

TH147-P and TH148LE-P

400-147-000-D 18/4/06 4/5

•

. Warranty

Start time

Temperature

setpoint

Day to program

Aube warrants this product, excluding battery, to be free from

defects in the workmanship or materials, under normal use and ser-

vice, for a period of one (1) year from the date of purchase by the

consumer. If at any time during the warranty period the product is

determined to be defective or malfunctions, Aube shall repair or

replace it (at Aube's option).

Period number

•

To select a day to program, press [ Day ] until the day is dis-

played. Hold for 3 seconds to select all 7 days.

MO: Monday, TU: Tuesday, WE: Wednesday, TH: Thursday,

FR: Friday, SA: Saturday and SU: Sunday).

(

If the product is defective,

Note: When all 7 days are selected, the settings of the displayed

period are copied to all 7 days. For example, if period 1 is dis-

played and you then select all 7 days, they will all have the same

settings for period 1. Similarly, if you then display period 2 while

all 7 days are already selected, they will now have the same set-

tings for period 2.

(

i) return it, with a bill of sale or other dated proof of purchase, to

the place from which you purchased it, or

(

ii) contact Aube. Aube will make the determination whether the

product should be returned, or whether a replacement product

can be sent to you.

This warranty does not cover removal or reinstallation costs. This

warranty shall not apply if it is shown by Aube that the defect or mal-

function was caused by damage which occurred while the product

was in the possession of a consumer.

•

To set the start time of a period, first press [ P# ] until the period

number is displayed and the time display flashes. Then press the

buttons. The time changes in 15-minute increments.

Note: If you want to skip (cancel) a period, press [ CLR ]. The

time and temperature display for that period will disappear. For

example, in the pre-programmed schedule, periods 2 and 3

have been skipped for Saturday and Sunday.

Aube's sole responsibility shall be to repair or replace the product

within the terms stated above. AUBE SHALL NOT BE LIABLE FOR

ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCI-

DENTAL OR CONSEQUENTIAL DAMAGES RESULTING,

DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WAR-

RANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF

THIS PRODUCT. Some provinces and states do not allow the

exclusion or limitation of incidental or consequential damages, so

this limitation may not apply to you.

•

To set the temperature for a period, first press

P# ] until the period number is displayed and the

temperature display flashes. Use the Heat/Cool

selector to display either the heating setpoint or the

cooling setpoint. Set the temperature using the

buttons.

[

THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEY-

WELL MAKES ON THIS PRODUCT. THE DURATION OF ANY

IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF

MERCHANTABILITY AND FITNESS FOR A PARTICULAR PUR-

POSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF

THIS WARRANTY. Some provinces and states do not allow limita-

tions on how long an implied warranty lasts, so the above limitation

may not apply to you.

Press [ Exit ] to exit the programming mode.

. Technical Specifications

Power supply: 2 AA batteries

Maximum load: 1 A @ 24 Vca per output

This warranty gives you specific legal rights, and you may have

other rights which vary from province or state to another.

Unoccupied load: 12 VCC / ± 10% / 20 mA

Setpoint range (heating): 5 to 28°C (41 to 82°F)

Setpoint range (cooling): 15 to 35°C (59 to 95°F)

Display range: -10 to 50°C (14 to 122°F)

. Service

Storage temperature: -20 to 50°C (-2 to 122°F)

Temperature display resolution: 0.5°C (1°F)

Accuracy: ± 0.5°C (1°F)

If you have any questions about the product installation, operation

or warranty, contact us at:

705 Montrichard

Saint-Jean-sur-Richelieu, Quebec

J2X 5K8

Cycle length: 10, 12, 15, 20 or 30 min. (programmable)

Compressor short-cycle protection (minimum off time): 5 minutes

Program protection: non-volatile memory

Dimensions: 127 mm x 75 mm x 28 mm (5 in. x 3 in. x 1 in.)

Canada

Tel.: (450) 358-4600

Toll-free: 1-800-831-AUBE

Fax: (450) 358-4650

Email: aube.service@honeywell.com

For more information on our products, go to

www.aubetech.com

As an ENERGY STAR partner, Aube Technologies has

determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

TH147-P and TH148LE-P

400-147-000-D 18/4/06 5/5

Honeywell CG511A1000 Thermostat User Manual

Honeywell TH5000 Thermostat User Manual

Honeywell T4039F Thermostat User Manual

Honeywell PCR426W Thermostat User Manual

White Rodgers 2061 Thermostat User Manual

Aprilaire 8551 Thermostat User Manual

White Rodgers 1.00E+56 Thermostat User Manual

Aprilaire Model 8570 Thermostat User Manual

Bryant A07049 Thermostat User Manual

White Rodgers 1F95 0477 Thermostat User Manual