Aube TH149 Thermostat User Manual

Home

href="
n
o
Loosen the locking screw (the screw cannot be com-  
pletely removed).  
TH149  
Electronic Thermostat  
Detach the front module from the back plate by pulling  
the bottom part.  
for Heat Pump and HVAC Systems  
Installation and User Guide  
1
.
Introduction  
The TH149 thermostat is used for the following systems:  
n
Heat pump (1H1C and 2H1C)  
HVAC (1H1C)  
p
q
If necessary, bore the mounting holes  
and insert anchors.  
The thermostat incorporates the following functions:  
System mode selection: heat, cool, auxiliary heat and off  
Fan mode selection: automatic or on (continuous)  
Emergency heat and fault LEDs  
Activation indicators (heat, cool, and auxiliary heat)  
Temperature display in °C or °F  
Backlit display  
Programmable heating and cooling cycle lengths  
Keypad lock  
Pass the wires through the opening of  
the back plate and fix the plate to the  
wall using the screws provided.  
2.3 Connecting the Thermostat  
The connection of the new thermostat should be similar to that of the old ther-  
mostat; however, it can vary depending on the installation.  
R; C Power; 24 VAC  
Emergency heat  
indicator  
Fault  
indicator  
W
Y
Heater. This connection is not required for HP-1H1C.  
Setpoint  
indicator  
Compressor  
Fan  
Fan mode  
selector  
G
Temperature  
display  
Reversing valve (see section 2.4). This connection is not required  
for HVAC-1H1C.  
O/B  
L
Auxiliary heat  
is On *  
Fault  
Cooling is On  
Heating is On  
System mode  
selector  
Temperature adjustment buttons  
*
Auxiliary heat is available only for 2H1C systems.  
2
.
Installation  
Note: The installation must be performed by a qualified electrician.  
2.4 Jumper settings  
o
The jumpers (JP1 and JP2), on the back of the front module, are used to con-  
figure the thermostat according to your system type:  
2
.1 Removing the Old Thermostat  
IN ORDER TO AVOID ANY RISK OF ELECTRIC SHOCK, CUT POWER TO  
THE HEATING SYSTEM.  
Jumper Parameter  
Settings  
Heat pump (HP position - default)  
HVAC (CN position)  
JP1  
JP2  
System  
n
o
Remove the old thermostat to access the wires.  
Identify and label each wire (with the corresponding letter on the old ther-  
mostat terminals) and remove them from the terminals.  
Reversing  
valve  
Activated in cool mode (O position - default)  
Activated in heat mode (B position)  
p
q
If necessary, strip the end of each wire (maximum of 6 mm).  
If necessary, wrap the wires around a pencil to pre-  
vent them from falling into the wall cavity.  
2.5 Completing the Installation  
n
Reinstall the front module onto the back plate and tighten the locking  
screw.  
r
If the opening in the wall is too big, insulate it using  
a non-flammable material to avoid air draughts  
behind the thermostat.  
o Place the system mode selector switch to OFF.  
Note: Leave the switch to OFF until you have verified that the thermostat is  
properly configured (see section 3).  
2
.2 Installing the Back Plate  
Note: For a new installation, choose a location approximately 1.5 m (5 feet)  
above the floor and on an inside wall. Avoid draughty areas (top of staircase,  
air outlet, etc.) or dead air spots (behind doors). Do not install the thermostat  
on a wall concealing air ducts nor expose it to direct sunlight.  
p
q
Apply power back to the system.  
Ensure that the thermostat is configured according to your system type  
(
see section 3).  
TH149  
400-149-000-B  
10/5/05  
1/2  
href="
3
.
4
.5 Setpoint Lock  
Configuration Menu  
p
A switch on the back of the front module can be used to lock the setpoint.  
The configuration parameters appear in the order shown below.  
n
o
p
Remove the front module from the  
back plate to access the switch.  
PARAMETERS  
DEFAULT  
OPTIONS  
°C or °F  
Temperature display  
Heating cycles per hour 1  
°C  
4
Place the switch (S1) to the I posi-  
tion.  
2, 3, 4, 5 or 6 2  
Cooling cycles per hour 1  
System type  
2, 3, 4, 5 or 6 2  
4
Reinstall the front module.  
2H  
HP  
2H (2H1C) or 1H (1H1C)  
HP (Heat Pump) or Cn (HVAC)  
1
H1C type 3  
5
.
1
When either the heating or the cooling parameter is displayed, use the  
mode selector switch to toggle between the two parameters.  
Technical Specifications  
Power supply: 24 VAC  
Maximum load: 1.5 A per output @ 24 VAC  
Setpoint range (heat): 5 to 28°C (41 to 82°F)  
Setpoint range (cool): 15 to 35°C (59 to 95°F)  
Setpoint increment: ± 0.5°C (1°F)  
Display range: -5 to 50°C (23 to 122°F)  
Display resolution: 0.5°C (1°F)  
r
2
3
The corresponding cycle lengths are: 2 = 30 min., 3 = 20 min.,  
4
= 15 min., 5 = 12 min., 6 = 10 min.  
This parameter appears only if you select 1H1C for the system type.  
n
o
p
q
To access the configuration menu, press and hold both temperature  
adjustment buttons for more than 3 seconds.  
To go to the next parameter, once in the menu, press both temperature  
adjustment buttons for more than 2 seconds.  
Short-cycle protection: 2 minutes  
Storage temperature: -20 to 50°C (-2 to 122°F)  
Dimensions: 79 mm x 81 mm x 25 mm (3.1 in. x 3.2 in. x 1.0 in.)  
To modify the displayed parameter, press one of the temperature adjust-  
ment buttons.  
6
.
Warranty  
You will exit the configuration menu at the end of the menu.  
s
Aube warrants this product, excluding battery, to be free from defects in the  
workmanship or materials, under normal use and service, for a period of three (3)  
years from the date of purchase by the consumer. If at any time during the warranty  
period the product is determined to be defective or malfunctions, Aube shall repair  
or replace it (at Aube's option).  
If the product is defective,  
i) return it, with a bill of sale or other dated proof of purchase, to the place from  
which you purchased it, or  
Note: The settings are not erased during a power outage.  
4
.
Operation  
q
4.1 System Mode  
(
(
Use the system mode selector switch to place the system in heat  
mode, cool mode, emergency heat (E.H.) mode, or off.  
ii) contact Aube. Aube will make the determination whether the product should be  
returned, or whether a replacement product can be sent to you.  
This warranty does not cover removal or reinstallation costs. This warranty shall  
not apply if it is shown by Aube that the defect or malfunction was caused by  
damage which occurred while the product was in the possession of a consumer.  
Aube's sole responsibility shall be to repair or replace the product within the terms  
stated above. AUBE SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF  
ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES  
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY  
WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS  
PRODUCT. Some provinces and states do not allow the exclusion or limitation of  
incidental or consequential damages, so this limitation may not apply to you.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY AUBE MAKES ON THIS  
PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE  
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS  
WARRANTY. Some provinces and states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you.  
Note: Emergency heat mode is not available on 1H1C systems.  
For these systems, placing the selector on E.H. is the same as  
placing it on Off.  
Auxiliary Heat  
Only 2H1C systems are equipped with auxiliary heat. The auxiliary heat is  
used in the following conditions:  
When the setpoint is not attained after a 15-minute delay following the  
compressor activation. After the delay, the auxiliary heating is used along  
with the compressor.  
When the thermostat is placed in emergency heating (E.H.). In this mode,  
only the auxiliary heat is used.  
4
.2 Fan Mode  
Use the fan mode selector switch to place the fan in automatic  
mode (AUTO) or continuous mode (ON).  
This warranty gives you specific legal rights, and you may have other rights which  
vary by province, state or region.  
Note: This switch is not functional if the fan is not connected to  
7
.
the thermostat.  
Technical Support  
For any questions regarding product installation or operation, contact our  
t
AUTO  
ON  
The fan operates only when heating or cooling is activated.  
The fan operates continuously.  
technical support team at:  
7
05, Montrichard  
Saint-Jean-sur-Richelieu, Quebec  
J2X 5K8  
4
.3 Viewing and Setting the Temperature  
Canada  
The actual temperature is normally displayed. To view the setpoint, press  
once on one of the temperature adjustment buttons. The setpoint is displayed  
Tel.: (450) 358-4600  
Toll-free: 1-800-831-AUBE  
Fax: (450) 358-4650  
Email: service@aubetech.com  
for 5 seconds and is indicated by the  
icon display. To change the setpoint,  
press the appropriate temperature adjustment button during the setpoint dis-  
play.  
For more information on our products, visit us at  
4.4 Backlight  
www.aubetech.com  
The display illuminates for 12 seconds when either of the temperature adjust-  
ment buttons is pressed.  
TH149  
400-149-000-B  
10/5/05  
2/2  

Aube TH113 Thermostat User Manual

Bryant T1 NAC Thermostat User Manual

Honeywell TH4210D Thermostat User Manual

Aube TH115 AFAF Thermostat User Manual

Trane TAYSTAT 540 Thermostat User Manual

Honeywell T8112D Thermostat User Manual

White Rodgers 1F86 0244 Thermostat User Manual

Aube TH146 N U Thermostat User Manual

Bryant TSTATBBP250 LA Thermostat User Manual

Carrier PTACSTAT NP HC Thermostat User Manual