Bryant PN TSTATBBP220 01 Thermostat User Manual

Home

user’s information

manual

TEMPSURE COMMERCIAL PROGRAMMABLE

THERMOSTAT (P/N TSTATBBP220-01)

Cancels: New

OM TSTAT-6

1/1/98

CONTENTS

CONFIGURATION

I. THERMOSTAT DISPLAY

Page

GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

The thermostat display is located in the center of the ther-

mostat. See Fig. 1. The following information can be dis-

played on the screen:

CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4

I. Thermostat Display . . . . . . . . . . . . . . . . . . . . . . .

II. Heat or Cool Indicator . . . . . . . . . . . . . . . . . . . .

III. Thermostat Front Panel Buttons . . . . . . . . . . . .

IV. Thermostat Programming Buttons . . . . . . . . . .

V. Set Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

VI. Programming Thermostat Schedules . . . . . . . .

• mode (OFF, HEAT, COOL, AUTO, or PROGRAM ON)

•

fan setting (FAN ON or blank)

override indication

room temperature

desired temperature

service ﬁlter indicator

OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

I. Auto-Changeover . . . . . . . . . . . . . . . . . . . . . . . . .

II. Two-Stage Operation . . . . . . . . . . . . . . . . . . . . . .

III. Clock Backup . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IV. Fan Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .

V. Emergency Heat . . . . . . . . . . . . . . . . . . . . . . . . . .

VI. Electric Heat . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

VII. Holiday Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .

• time of day

•

day of the week

schedule period (Occupied 1, 2, or 3; or Unoccupied)

• setup indicator (programming mode)

•

lock indicator

start/stop indicator (schedule period program mode)

IMPORTANT: Read entire instructions before starting the

installation.

GENERAL

Bryant’s 7-day, commercial, programmable thermostats are

wall-mounted, low-voltage thermostats which maintain room

temperature by controlling the operation of an HVAC (heat-

ing, ventilation, and air conditioning) system. Separate heat-

ing and cooling set points and auto-changeover capability

allow occupied and unoccupied programming schedules for

energy savings.

All thermostats allow up to 3 occupied and one unoccupied

time/temperature setting to be programmed per 24-hour

period. Each thermostat stores programs for 7 independent

days. Batteries are not required. During power interruption

the internal NEVERLOST™ memory stores programs for an

unlimited time.

Fig. 1 — Thermostat Display

II. HEAT OR COOL INDICATOR

IMPORTANT: The thermostat has a conﬁgurable security level.

If certain functions are not available (changing set points, chang-

ing programming schedules), the thermostat security level may

be conﬁgured to exclude those functions. Call the installer to

reconﬁgure the security level.

A Heat or Cool indicator is located on the bottom left cover of

the thermostat. See Fig. 2. The light will be red if the ther-

mostat is in Heating mode. The light will be green if the ther-

mostat is in Cooling mode.

III. THERMOSTAT FRONT PANEL BUTTONS

The thermostat has buttons on the front cover which are used

to raise or lower the desired set point and override the cur-

rent program. See Fig. 2.

A. Set Point Buttons

The UP ARROW and DOWN ARROW buttons will raise or

lower the current desired temperature set point. If the ther-

mostat is in AUTO mode, pressing the UP ARROW or DOWN

ARROW buttons will adjust both the heating and cooling set

points. Pressing the UP ARROW or DOWN ARROW buttons

in Cooling mode will adjust only the cooling set points. Press-

ing the UP ARROW or DOWN ARROW buttons in Heating

mode will adjust only the heating set points. The UP

ARROW and DOWN ARROW buttons are also used in Pro-

gramming mode.

Fig. 2 — Thermostat Front Panel Buttons

B. Override Button

The Override button is used to force the thermostat from Un-

occupied mode into the Occupied 1 mode comfort settings. The

Override period will be set at 30 minutes. The thermostat

will then return to Unoccupied mode. To increase the amount

of time in Override mode, press the Override button again.

Thirty minutes of override time will be added for each time

the Override button is pressed up to a maximum of 4 hours.

After the 4-hour limit has been reached, press the Override

button again to cancel Override mode.

While in Override mode, the Override icon and the

Occupied 1 icon will be displayed on the thermostat. The time

of day and the minutes remaining in Override mode will

alternate on the thermostat display.

Fig. 3 — Thermostat Programming Buttons

The set points are adjustable with the UP ARROW and DOWN

ARROW keys during Override mode.

NOTE: When the thermostat is in Unoccupied mode, the fan

will run only during heating or cooling operation, even if the

fan is set to FAN ON; this is the energy-saving smart fan

feature.

NOTE: If the thermostat is in Occupied mode and the Over-

ride button is pressed, the thermostat will go into Unoccu-

pied mode immediately. The thermostat will remain in Un-

occupied mode until the next Occupied start time.

When the fan is not set to FAN ON (no icon displayed on ther-

mostat screen), the fan will run during heating and cooling

operation only.

IV. THERMOSTAT PROGRAMMING BUTTONS

The thermostat has programming buttons which are used

to change the set points of the thermostat, set the modes, and

program schedules. The programming buttons are acces-

sible from underneath the thermostat cover. To access the pro-

gramming buttons, pull on the hinged thermostat cover. See

Fig. 3. The programming buttons are: Mode, Fan, Holiday,

Program, and Set Clock.

C. Mode Button Operation

The Mode button selects the operating mode of the thermo-

stat. If OFF is selected, the thermostat will not enter Heat-

ing or Cooling mode. If HEAT is selected, the thermostat will

only enter Heating mode (if the room temperature is below

the heating set point). If COOL is selected, the thermostat

will only enter Cooling mode (if the room temperature is above

the cooling set point). If AUTO is selected, the thermostat will

enter Heating or Cooling mode based on the room tempera-

ture and the heating and cooling set points. If PROGRAM

ON is selected, the stored schedule is enabled and the ther-

mostat will follow the Occupied and Unoccupied schedules

stored in its memory.

The UP ARROW and DOWN ARROW buttons are used to

scroll through programming set points. The buttons are also

used to answer yes or no.

A. Keypad Lock

The thermostat has a keypad lockout feature which will not

acknowledge front panel buttons until the lockout sequence

is entered. To disable or lock the keypad, press and hold the

Mode button. While holding down the Mode button, press the

UP and DOWN ARROW buttons simultaneously. The ‘‘Locked’’

icon will appear on the display.

Auto-Changeover

When the thermostat mode is set to AUTO, the thermo-

stat will provide automatic changeover from Heating to Cool-

ing mode and Cooling to Heating mode when required. The

thermostat will automatically switch to maintain the desired

temperature setting. The thermostat does not need to be manu-

ally changed from heating to cooling or cooling to heating

operation.

The thermostat is unlocked by performing the same proce-

dure. Press and hold the Mode button. While holding down

the Mode button, press the Up and Down Arrow buttons

simultaneously. The ‘‘Locked’’ icon will be removed from the

display.

D. Holiday Mode

B. Fan Button Operation

The Holiday button places the thermostat into Holiday mode.

During Holiday mode, the unoccupied set points are

enforced. The number of days the thermostat will be in Holi-

day mode can be set.

The Fan button selects fan operation. When the fan is set to

FAN ON, the fan will run continuously for improved air

circulation.

—

2—

V. SET CLOCK

The Set Clock button allows the user to change the time and

day displayed on the thermostat. Press the Set Clock button

to enter Set Time mode. See Fig. 4. The current time will

blink on and off. Press the UP ARROW and DOWN ARROW

buttons until the correct time is shown. Hold down the but-

tons to quickly move through the time display. The AM and

PM annunciators will automatically change. To scroll through

by hours only, press and hold down the Fan button while press-

ing the UP or DOWN ARROW buttons. To ensure the sched-

ules are properly followed, make sure that AM or PM is

correct for the time chosen. When the correct time is shown,

press the Mode button to modify the day of the week. The

current day will blink on and off. Press the UP ARROW and

DOWN ARROW buttons until the correct day is shown. Press

the Set Clock button again to exit the Set Time mode.

Fig. 5 — Setting Occupied 1 Set Points

. The cooling set point for Unoccupied will be displayed.

Use the UP ARROW and DOWN ARROW buttons to

raise or lower the cooling set point until the desired

temperature is shown. The range of acceptable values

is 35 to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied cool-

ing). Press the Mode button to continue.

. The heating set point for Unoccupied will be dis-

played. Use the UP ARROW and DOWN ARROW but-

tons to raise or lower the heating set point until the

desired temperature is shown. The range of acceptable

values is 35 to 99 F (1 to 37 C) or ‘‘OF’’ (no unoccupied

heating). Press the Mode button to continue.

. The day of the week will be shown. Use the UP

ARROW and DOWN ARROW buttons to change the

day of the week until the desired starting day is shown.

Possible choices are M (Monday) through S (Sunday).

Press the Mode button when the desired day is shown.

Fig. 4 — Setting the Clock

VI. PROGRAMMING THERMOSTAT SCHEDULES

. The Start Time for Occupied 1 will be displayed. Use

the UP ARROW and DOWN ARROW buttons to raise

or lower the time until the desired Start Time is shown.

Press the Mode button to continue. See Fig. 6.

Before programming the thermostat, plan the thermostat daily

schedule. The schedule is divided into 7 days (Monday through

Sunday). Each day can have 2 (Occupied 1, Unoccupied),

(Occupied 1, Occupied 2, Unoccupied), or 4 (Occupied 1,

Occupied 2, Occupied 3, Unoccupied) time periods. Each

occupied time period has a start time, stop time, heating set

point and a cooling set point. The unoccupied time period has

a heating set point and a cooling set point. The unoccupied

time period is active whenever an occupied time period is not

active. Fill in Table 1 below as an aid to programming the

daily schedules.

A. Programming Mode

To program the daily schedules, perform the following

procedure:

. Enter programming mode by pressing the Program but-

ton. The Occupied 1 annunciator will appear on the ther-

mostat display. See Fig. 5. Use the UP ARROW and

DOWN ARROW buttons to set the maximum number

of Occupied periods available. The thermostat can be

set to 1, 2, or 3. After the number of Occupied periods

has been selected, press the Mode button.

Fig. 6 — Start Time Display

. The Stop Time for Occupied 1 will be displayed. Use

the UP ARROW and DOWN ARROW buttons to raise

or lower the time until the desired Stop Time is shown.

Press the Mode button.

. The cooling set point for Occupied 1 will be displayed.

Use the UP ARROW and DOWN ARROW buttons to

raise or lower the cooling set point until the desired

temperature is shown. The range of acceptable values

is 35 to 99 F (1 to 37 C). Press the Mode button to con-

tinue. See Fig. 5.

. The On/Off icon will be displayed. Use the UP ARROW

to turn the Occupied 1 period ON for this day. Use the

DOWN ARROW to turn the Occupied 1 period OFF for

this day.

10. Repeat Steps 2 through 9 to program the remain-

ing schedule for occupied periods 2 and 3 (if selected in

Step 1).

. The heating set point for Occupied 1 will be displayed.

Use the UP ARROW and DOWN ARROW buttons to

raise or lower the heating set point until the desired

temperature is shown. The range of acceptable values

is 35 to 99 F (1 to 37 C). Press the Mode button to con-

tinue. See Fig. 5.

—

3—

Table 1 — Daily Schedule Planner

SCHEDULE

Occupied 2

DAY

OF THE

WEEK

Occupied 1

Occupied 3

Unoccupied

Start / Stop / Heat / Cool

Heat / Cool

Monday

Tuesday

Wednesday

Thursday

Friday

Saturday

Sunday

NOTE: The cooling temperature set point must be higher than the heating temperature set point.

1. The Copy command can be used to copy the previous

day’s schedule if the schedules are the same. The copy

command becomes available after all the occupied

periods are programmed in a day. Use the UP ARROW

to change the copy command to YES. Use the DOWN

ARROW to change the copy command to NO. Press the

Mode button when the choice has been made. See

Fig. 7.

12. After all the times and set points for each day have

been entered, press the Program button to ﬁnish en-

tering the schedule.

NOTE: The thermostat will continue to follow the schedule

until a new one is entered.

•

If only one occupied schedule is selected, the Occupied 2

and 3 schedules are skipped.

If the start time is set later in the day than the stop time,

the program will run from midnight of that day to the stop

time and then from the start time to midnight.

If NO was selected, the schedule will automatically

change to the next day and the user must enter the oc-

cupied and unoccupied schedules for that day.

•

If the same start and stop times are programmed for an

occupancy schedule, the thermostat will be in Occupied mode

for 24 hours.

NOTE: Occupied 1 schedule heating and cooling set points

are the same for each day. Occupied 2 and 3 set points may

be set to different values for each day of the week.

If one occupied period starts or stops within another occu-

pied period, the lower numbered schedule has priority. For

example, if schedule Occupied 3 is running for 24 hours

and occupied schedule 2 comes on from 1 to 3 PM, the set

points from Occupied 2 are in effect from 1 to 3 PM.

If YES was selected, the schedule will be copied to the

next day. The schedule copy may be repeated until Sun-

day is reached. The Sunday schedule cannot be copied

to Monday.

B. Overriding the Schedule

The schedule can be overridden during operation by pressing

the UP or DOWN ARROW buttons to change the desired tem-

perature. The thermostat will use the new set point until the

next scheduled time period starts.

Fig. 7 — Copy Command Display

—

4—

OPERATION

V. EMERGENCY HEAT

The Mode button selects the operating mode of the thermo-

stat. If OFF is selected, the thermostat will not enter Heat-

ing or Cooling mode. If HEAT is selected, the thermostat will

only enter Heating mode (if the room temperature is below

the heating set point). If COOL is selected, the thermostat

will only enter Cooling mode (if the room temperature is above

the cooling set point). If AUTO is selected, the thermostat will

enter Heating or Cooling mode based on the room tempera-

ture and the heating and cooling set points. If PROGRAM

ON is selected, the stored schedule is enabled and the ther-

mostat will follow the Occupied and Unoccupied schedules

stored in its memory.

Emergency heat is available for heat pump applications. To

turn on emergency heat, press and hold the Fan button. While

holding the Fan button, press the UP button for 2 seconds.

An ‘‘EH’’ will be displayed. During emergency heat, the fan

will operate and the second stage of heat will be energized

(locking out the ﬁrst stage compressor). To exit emergency

heat, press and hold the Fan button. While holding the Fan

button, press the UP button for 2 seconds. During emergency

heat, only OFF and HEAT modes are available.

VI. ELECTRIC HEAT

When the Electric Heat option in the advanced set up is set

to ON (conﬁgured by installer), the thermostat will turn on

the fan immediately any time there is a heat demand. This

feature should only be used on electric heating applications.

Do not use with gas heat.

I. AUTO-CHANGEOVER

When the thermostat mode is set to AUTO, the thermo-

stat will provide automatic changeover from Heating to Cool-

ing mode and Cooling to Heating mode when required. The

thermostat will automatically switch to maintain the desired

temperature setting. The thermostat does not need to be manu-

ally changed from heating to cooling or cooling to heating

operation.

VII. HOLIDAY MODE

When the thermostat is in Holiday mode, the thermostat will

operate under Unoccupied set points. To conﬁgure and acti-

vate the Holiday mode, press the Holiday button. The ‘‘HOL’’

icon will be displayed along with the remaining days of Holi-

day mode operation. Press the UP or DOWN ARROWS to

select the number of days that the holiday schedule will be in

effect. A value of 0 disables Holiday mode. The duration can

be set from 1 to 99 days. The thermostat will enter Holiday

mode on midnight of the next day after the mode has been

activated. Holiday mode will remain in effect until midnight

of the last conﬁgured day.

II. TWO-STAGE OPERATION

The second stage of heat or cool is turned on when the ﬁrst

stage has been on for a minimum of 2 minutes and the tem-

perature differential from the set point is equal to or greater

than the set point plus the deadband plus 2 degrees.

III. CLOCK BACKUP

In the event of a power loss, the thermostat will keep

time for a minimum of 48 hours without external power or

batteries.

If the Holiday mode is in effect, the number of days remain-

ing will blink on and off and the ‘‘Unoccupied’’ icon will be

displayed. The Override button will be active during Holiday

mode.

IV. FAN OPERATION

To turn off the Holiday mode before the remaining conﬁg-

ured days have passed, press the Holiday button to enter the

conﬁguration mode. Press the DOWN ARROW to set the num-

ber of days to zero. Holiday mode will be disabled.

If Fan On is selected, the fan will run continuously during

occupied schedule (except when Mode is switched to OFF).

The fan will be off during unoccupied schedule except during

heating or cooling operation.

If Fan On is not selected, the fan will only operate during

heating or cooling operation.

—

5—

—

6—

Printed in U.S.A.

CATALOG NO. 809-696

Honeywell T8001 Thermostat User Manual

Lux Products DHP2120 Thermostat User Manual

Trane 570 Thermostat User Manual

Honeywell V2000 Thermostat User Manual

Honeywell T87F DESIGNER Thermostat User Manual

Carrier TM016 028 Thermostat User Manual

Honeywell RTH8500 Thermostat User Manual

Lux Products P2000F Thermostat User Manual

White Rodgers F145 1082 Thermostat User Manual

Emerson 37E73A 906 Thermostat User Manual