Bryant T2 PAC Thermostat User Manual

TABLE OF CONTENTS

PAGE

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

INSTALLATION CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 1 — Thermostat Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 2 — Install Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Step 3 — Set Thermostat Configuration . . . . . . . . . . . . . . . . . . . . . . . 10

Step 4 — Check Thermostat Operation . . . . . . . . . . . . . . . . . . . . . . . . 18

FEATURES AND ACCESSORIES . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

OPERATIONAL AND CONNECTION INFORMATION . . . . . . . . . . 22

WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

THERMOSTAT CONFIGURATION RECORD . . . . . . . . . . . . . . . . . . 32

1

SAFETY CONSIDERATIONS

Read and follow manufacturer instructions carefully. Follow all local electrical

codes during installation. All wiring must conform to local and national electrical

codes. Improper wiring or installation may damage thermostat.

Recognize safety information. This is the safety -alert symbol

. When you see

this symbol on the equipment and in the instruction manual, be alert to the potential

for personal injury.

Understand the signal words DANGER, WARNING, and CAUTION. These

words are used with the safety -alert symbol. DANGER identifies the most serious

hazards which will result in severe personal injury or death. WARNING signifies a

hazard which could result in personal injury or death. CAUTION is used to identify

unsafe practices which may result in minor personal injury or product and property

damage. NOTE is used to highlight suggestions which will result in enhanced

installation, reliability, or operation.

2

INTRODUCTION

Bryant’s Legacyt Series programmable thermostats are wall-mounted,

low -voltage thermostats which maintain room temperature by controlling the

operation of a heating and/or air conditioning system. Both heat pump and air

conditioner models are available, each in programmable and non -programmable

versions. A variety of features are provided including battery operation, separate

heating and cooling setpoints, auto changeover, keypad lockout, backlighting, and

built-in installer test. Programming features include 7 -day (all days the same) and

5

/2 (Mon -Fri and Sat-Sun) with 2 or 4 periods per day.

This Installation Instruction covers installation, configuration, and start -up of all

four versions of the Legacy Series line of thermostats. For operational details,

consult the Owner’s Manual for the specific thermostat you are installing.

3

INSTALLATION CONSIDERATIONS

Models

There are four models in the Legacy Series: programmable and non -programmable, AC

and HP. Models T2 -PAC and T2 -NAC are designed for AC systems, controlling one

stage of cooling and one stage of heating. They will not operate a heat pump. Models

T2 -PHP and T2 -NHP are designed for HP systems, controlling two stages of cooling

and three stages of heating. They can be converted to AC operation. Select the

appropriate model for the intended application.

Power

All Legacy Series models are dual powered. They can operate from batteries or

2

4VAC power. Operation from 24VAC is preferred if available. Battery operation is

used when there are not enough wires to support 24VAC operation or when

armchair programming” is desired. For an AC system, up to six wires are needed

“

for 24VAC operation and one less wire for battery operation. For a HP system, up to

seven wires are needed for 24VAC operation and and one less wire is sufficient for

battery operation. For heat only operation with batteries, only two wires are

required. When battery operation is used, the C terminal does not need to be

connected.

Provision is also made for separate heating and cooling transformers via separable Rc

and Rh terminals which are connected via factory -installed jumper wire.

4

INSTALLATION

Step 1 — Thermostat Location

S

Approximately 5 ft (1.5m) from floor.

S

Close to or in a frequently used room, preferably on an inside partition-

ing wall.

S

On a section of wall without pipes or duct work.

Thermostat should NOT be mounted

S

Close to a window, on an outside wall, or next to a door leading to the

outside.

Exposed to direct light or heat from the sun, a lamp, fireplace, or other

temperature -radiating objects which could cause a false reading.

Close to or in direct airflow from supply registers and return -air re-

gisters.

In areas with poor air circulation, such as behind a door or in an alcove.

Step 2 — Install Thermostat

WARNING

!

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury or

death.

Before installing thermostat, turn off all power to equipment. There

may be more than one power disconnect.

1

2

. Turn OFF all power to unit.

. If an existing thermostat is being replaced:

a. Remove existing thermostat from wall.

5

b. Disconnect wires from existing thermostat, one at a time. Be careful not

to allow wires to fall back into the wall.

c. As each wire is disconnected, record wire color and terminal marking.

d. Discard or recycle old thermostat.

CAUTION

ENVIRONMENTAL HAZARD

!

Failure to follow this caution may result in environmental damage.

Mercury is a hazardous waste. Federal regulations require that

Mercury be disposed of properly.

3

4

. Open thermostat (mounting base) to expose mounting holes. The base can

be removed to simplify mounting. Press the thumb release at the top of the

thermostat and snap apart carefully to separate mounting base from re-

mainder of thermostat.

. Route thermostat wires through large hole in mounting base. Level mounting

base against wall (for aesthetic value only—thermostat need not be level for

proper operation) and mark wall through four mounting holes. To avoid unin-

tended bending of wall plate plastic, all four screws and anchors must be used.

See Fig. 1.

6

A07153

Fig. 1 - Backplate Mounting

5

6

. Drill four 3/16 -in. mounting holes in wall where marked.

. Secure mounting base to wall with four screws and anchors provided. To

avoid unintended bending of wall plate plastic, all four screws and anchors must

be used. Make sure all wires extend through hole in mounting base.

7

. Adjust length and routing of each wire to reach proper terminal and con-

nector block on mounting base with 1/4 -in. (6 mm) of extra wire. Strip only

1

/4 in. of insulation from each wire to prevent adjacent wires from shorting

together when connected. See Fig. 2.

A07155

Fig. 2 - Secure Wires to Terminal Strip

. Match and connect equipment wires to proper terminals of the connector blocks

see Fig. 3). If there are separate 24VAC transformers, one in the indoor unit

8

(

and one in the outdoor unit, connect the common of each to the C terminal.

Remove factory -installed jumper wire from Rc and Rh terminals. Connect the

R from the indoor unit to the Rh terminal. Connect the R from the outdoor unit

to the Rc terminal. Then the W signal is taken from the Rh power and the Y1,

Y/Y2, G and O signals are taken from the Rc power.

8

Rc - 24 VAC, from cooling equipment

Rh - 24 VAC, from heating equipment

W - Heating

C - Common 24 VAC

O/B - reversing valve

G - Fan

Y1 - Cooling

Low Stage

Y/Y2 - Cooling High or Single Stage

A09271

Fig. 3 - Terminal Designations

CAUTION

ELECTRICAL OPERATION HAZARD

!

Failure to follow this caution may result in equipment damage or

improper operation.

Improper wiring or installation may damage the thermostat. Check to

make sure wiring is correct before proceeding with installation or

turning on unit.

9

. Push any excess wire into wall and against mounting base. Seal hole in wall

to prevent air leaks. Leaks can affect operation.

1

0. Snap case back together. Attach thermostat to backplate by inserting tab on

bottom edge and hinging up until top snap secures. See Fig. 4

9

A07158

Fig. 4 - Attach Thermostat to Backplate

11. Close thermostat assembly making sure pins on back of circuit board align

with sockets in connector.

1

2. Turn ON power to unit.

When power is applied, all display icons are lit for 2 seconds to test the display.

Following this, the equipment type for which the thermostat is configured is displayed

for an additional 2 seconds. It will be one of HP, H2, AC, A2, H or C (see explanation

under Step 3, Option 01 below). A HP thermostat configured to operate an AC (see

Option 1 below) will display AC. An AC thermostat cannot display HP.

NOTE: If a common wire has not been connected, two AA batteries must be used

to power the thermostat.

Step 3 — Set Thermostat Configuration

Configuration options enable the installer to configure the thermostat for a particular

installation. Most are not presented to the homeowner and therefore must be properly set

by the installer. (Only those marked with an asterisk * below are available to the

homeowner.) Following is a list of the options available, an explanation of their function,

1

0

and their factory default settings. Not all numbers are used in the Legacy Series because

not all options are available in this series - and numbering is consistent across the T1,

T2, and T6 thermostat lines.

Configuration Options - Summary:

Option 01

Option 03*

Option 04

Option 07

Option 10

Option 11

Option 12

Option 13

Option 15

Option 16

Option 17

Option 18*

Option 21*

Option 24*

Option 25*

Option 26

Option 27

Option 99

-

Equipment type

Fahrenheit/Centigrade

Fan (G) on with W output

Zoning

Reversing valve

Minimum deadband between heating and cooling setpoints

Smart Recovery (programmable models only)

Room air temperature offset adjustment

Auto Changeover availability

Maximum cycles per hour

Time between equipment stages

Continuous backlighting

Keypad lockout

Programmable/non -programmable (programmable models only)

Number of programmable periods per day

Minimum cooling setpoint

Maximum heating setpoint

Reset to factory defaults

Those options marked with an asterisk are also adjustable by the homeowner. See

Owner’s Manual for further information.

11

To Enter the Configuration Mode:

Press and hold the FAN key for about 10 seconds until the display changes so that

only two pairs of digits are showing. The left (programmable version) or the large

upper (non -programmable version) display shows the configuration number and

the right (programmable version) or small lower (non -programmable version)

shows the configuration setting. Configuration number will be flashing which

means it can be adjusted using the UP and DOWN keys. To cause the opposite pair

to flash (to be adjustable), press the MODE key. Successive presses of the MODE

key alternate between the configuration number and the configuration setting. To

exit the configuration mode, press the FAN key. If no key is pressed for 3 minutes,

the configuration mode will automatically exit, returning the thermostat to normal

operation.

Configuration Options -- Selection:

Option 01 - Equipment type

Selections: with HP thermostat: HP, H2, AC, A2, H, C

with AC thermostat: AC, H, C

HP controls 1 speed heat pump with 1 stage of aux heat.

A2 controls two stages of cooling and one stage of furnace heat.

H2 controls a 2 Speed HP with 1 stage of aux heat.

AC controls 1 speed air conditioner with 1 stage of heat.

H operates a heat only system: furnace or fan coil only; no outdoor unit.

C operates a cool only system: outdoor AC unit with an indoor fan coil; no strip

heater support.

Note that this option allows a HP thermostat to be converted to control an AC

system.

1

2

Option 03 - Fahrenheit/Centigrade

Selections:

F = Fahrenheit — Default is Fahrenheit.

C = Centigrade.

Selects temperature measurement units.

Option 04 - Fan (G) ON with W output

Selections:

OF = G not energized with W — This is default.

ON = G energized with W.

This selection determines whether the fan (G) is to be ON or OFF when the W

(

furnace or strip heat) is ON. Furnaces and fan coils which manage their own

blowers do not require a separate G signal. Some auxiliary heaters require a

separate G signal to operate the blower when W is applied.

Option 07 - Zoning

Selections:

OF = non -zoned system — This is default.

ON = zoned system.

ON disables thermostat’s internal timers which are not needed with zoning system

controls. Must be set to OF for non -zoned systems.

Option 10 - Reversing valve

This selection is only available on heat pump systems. “O” terminal can be

configured to be energized in either heating mode or in cooling mode, depending

on heat pump operation. “O” is used to describe a heat pump system that energizes

its reversing valve in cooling. “B” is used to describe a heat pump system that

energizes its reversing valve in heating.

1

3

H — Reversing valve output (O/W2/B) is energized when HEAT mode is selected.

C — Reversing valve output (O/W2/B) is energized when COOL mode is selected.

Default is C.

Option 11 - Minimum Deadband Between Heating And Cooling

Selections:

0

1 through 06 — Default is 02.

Sets the minimum allowable number of degrees between heating and cooling

setpoints. One setpoint will “push” the other to maintain this difference.

Option 12 - Smart Recovery (programmable model only)

Selections:

OF, 30, 60, 90 — Default is 90.

Smart Recovery OF means setpoints change immediately at a program schedule

change. Thirty, 60, or 90 selects the number of minutes recovery starts before

programmed recovery time. Recovery takes place smoothly during the selected

recovery time, ending at the recovery time and temperature which is programmed.

If the setpoint is changed during smart recovery, the smart recovery is cancelled and

the new setpoint is effective immediately. Not available with non -programmable

thermostats.

1

4

Option 13 - Room Air Temperature Offset

Selections:

-

5 to 5_ F — Default is 0.

This option selects the number of degrees F to be added to the displayed

temperature to calibrate or deliberately miscalibrate the measured room

temperature.

Option 15 - Auto Changeover Availability

Selections:

ON — This is default.

OF

ON allows automatic changeover between heating and cooling as demand requires.

OF maintains either heating or cooling mode only. Auto changeover is not available

when H or C is selected under Option 1.

Option 16 - Maximum Cycles Per Hour

Selections:

2

, 4, or 6 — Default is 4.

The maximum cycle rate is limited by internal timers to the selected number of

cycles per hour. Selection of a higher number causes faster cycling resulting in

more constant room temperature.

Option 17 - Minimum Time Between Equipment Stages

Selections:

1

0, 15, 20, 25 — Default is 15.

When there is an auxiliary stage of heat available, this is the amount of time the

heat pump must operate before the aux stage can turn on. With heat pumps, longer

times can reduce the amount of auxiliary heat used. Not available with AC

thermostats.

1

5

Option 18 - Backlight Configuration

Selections:

ON, OF — Default is OF.

When ON is selected and the thermostat is not battery operated a low level

continuous display backlight is always on. With OF selected, the backlight is only

on for a short time after the door is opened or a key is pressed. Continuous

backlight is not available with battery operation.

Option 21 - Keypad Lockout

Selections:

ON, OF — Default is OF.

With OF selected, the keypad cannot be locked. With ON selected the keypad will

be locked and can be unlocked by simultaneously pressing the UP and DOWN keys

for 5 seconds. Once unlocked, it will relock 2 minutes after the last keypad press. A

“

lock” icon is displayed while it is locked.

Option 24 - Programmable/Non-Programmable (programmable model only)

Selections:

P, nP — Default is P.

This option is only available on programmable models, allowing programming to

be disabled when nP is selected. The clock is displayed, but the program schedule,

the HOLD and TEMPORARY HOLD functions are disabled.

Option 25 - Number of Programmable Periods (programmable models only)

Selections:

2

, 4 — Default is 4.

Selecting 2 allows 2 programming periods, P1 and P2, per day. Selecting 4 allows

periods P1, P2 , P3, and P4. Not available with non -programmable thermostats.

1

6

Option 26 - Minimum Cooling Setpoint

Selections:

5

2_F to 90_F — Default is 52_F.

Sets the lowest cooling setpoint available to the user.

Option 27 - Maximum Heating Setpoint

Selections:

5

0_F to 88_F — Default is 88_F.

Sets the highest heating setpoint available to the user.

Option 99 - Reset to Factory Defaults

Selection:

See below — There is no default.

Use this capability to reset the thermostat to “out of the box” conditions.

NOTE: All configuration settings, program settings, clock, and day which have

been manually entered will be lost!

When this option is selected, the configuration number (99), will appear on the left

and 10 will appear on the right. To perform the reset, first use the MODE key to

make the 10 flash. Then press and hold the DOWN key. The 10 will start counting

down toward zero. If the DOWN key is kept pressed until the count reaches zero,

the reset will be performed. If the DOWN key is released early, the number will

return to 10 and the reset will not occur.

1

7

Step 4 — Check Thermostat Operation

The Legacy Series thermostats have a built -in installer test capability. Use it to

check thermostat and equipment operation without delays or setpoint adjustments

to force heating or cooling.

To enter the Installer Test mode, use the same process as is used to enter Installer

Configuration, only hold the FAN key longer. More specifically, press and hold the

FAN for about 15 seconds until the display reads In on the left and St on the right

for the programmable model, or InS in the smaller display for the

non -programmable model. The MODE will be OFF. The MODE key (upper left)

can now be used to select heat, cool, or emergency heat, if this is a HP thermostat.

Selecting one of the available modes will immediately command the equipment to

turn on in that mode. It will run for 3 minutes and then return the mode to off. With

HP thermostats (having 2 stages of heating), the test will run for 3 minutes on each

stage. If the thermostat is programmable, the clock display counts down from 180

seconds while each stage operates. Changing the mode to OFF will terminate any

running test immediately.

During any test, the display icons will be displayed the same as for normal

operation of that stage, as follows:

SELECTED MODE

DISPLAY ICONS

off

cool

cool on

heat

heat on, aux heat on

aux heat on

Em Heat

To terminate the Installer Test mode press the DONE or FAN button. If the

thermostat is left in Installer Test mode, it will revert back to normal operation after

1

5 minutes.

1

8

Checklist

1

. Run equipment through several heating and cooling cycles to ensure proper

operation. To operate the thermostat in its normal operating mode, consult

the Owner’s Manual.

2

. If the equipment is to be left in operation, the setpoints, operating mode,

and possibly program schedule must be properly selected.

3

4

. Put away tools and instruments and clean up debris.

. Review and leave Owner’s Guide with owner.

1

9

FEATURES AND ACCESSORIES

Home, Away, Sleep (programmable models only)

This feature provides three button selections which select from three predetermined

pairs of heat and cool setpoints. In programmed versions, one of these three choices

can be selected for any programmed period. To change these settings, a temperature

is first selected and then the key pressed and held, similar to setting stations on a

push -button radio. See Owner’s Manual for details.

Clock (programmable models only)

Without batteries the clock will continue to operate for 8 hours while power is

removed. With batteries, the clock operates until the end of the battery life.

Batteries

Battery operation is available for installations where there is no common (C) wire

available at the thermostat or where operation is to continue while the thermostat is

removed from the wall, usually to facilitate remote (armchair) programming. For

battery operation, install two alkaline AA batteries. The thermostat is designed to

operate up to one year on a set of batteries. A battery indicator on the display warns

when battery replacement is needed. See Homeowners Guide for details. If batteries

are installed and the thermostat is operated from 24VAC power, battery operation

will occur only when 24VAC power is not present. The changeover between

2

4VAC power and battery power is automatic.

Display Lighting

The display has two levels of lighting, high level and low level. High level lighting

comes on for 10 seconds when the door is opened and/or buttons are being pressed

with 24VAC and with batteries. Low level lighting is only available if the

thermostat is operated from 24VAC. It is not available with batteries. The low level

can be selected (see Option 18) for continuous backlight.

2

0

Door Switch

When the door is opened, the display changes from its normal operation view.

The

large temperature display disappears so it will be available for other user functions. If the

door is left open for 3 minutes, the display reverts to normal operation.

Mounting Options

For those installations requiring it, mounting hole locations for the programmable

model are spaced to fit either a horizontal or vertical junction box. Mounting hole

locations for the non -programmable are spaced to fit a horizontal junction box.

2

1

OPERATIONAL AND CONNECTION INFORMATION

Rc/Rh Connections

For installations having a separate 24VAC transformer for heating and cooling, the

R connection can be separated into two connections, one for each transformer. This

allows isolation between the two transformers to be preserved. To separate Rc from

Rh, remove the factory supplied jumper between the Rc and Rh terminals. The Rh

terminal powers the W output. The Rc terminal powers the Y1, Y/Y2, G and O

outputs.

Wiring

For all wiring applications, use 22 AWG or larger wire. Continuous wire lengths

over 100 ft. (30.5 m) should use 20 AWG or larger. Wire lengths are not to exceed

2

50 ft. (76 m) per run.

O/B Terminal -- On HP Thermostat Only

This terminal is normally connected to the reversing valve of the heat pump. It is

called O when the valve is energized in cooling and B when it is energized in

heating. Option 10 of the Configuration Options makes the O/B selection.

Timers

There are several timers which influence the thermostat’s operation:

If any of the timers listed below is preventing the equipment from turning on, the

display icons which show the equipment is operating will be flashing to indicate a

turn -on delay is present.

Five-Minute Compressor Timeguard

This timer prevents the compressor from starting unless it has been off for 5

minutes. It can be defeated for one cycle by simultaneously pressing the FAN and

UP keys.

2

Minimum On Timer

Once the equipment has been turned on, it must remain on for 3 minutes. A change

in mode or setpoint will cancel this timer.

Cycle Timer

Based on the selection of 2, 4, or 6 cycles per hour, this timer is set to 30, 15, or 10

minutes. This much time must elapse from the start of one cycle before another

cycle can start. It serves to impose the cycles per hour limits. It can be defeated for

one cycle by simultaneously pressing the FAN and UP keys.

Auto Changeover Timer

To prevent unnecessary cycling between heating and cooling modes, this timer

prevents a changeover to the opposite mode until a demand exists in the opposite

mode for 20 minutes. It is defeated when setpoints are changed so that the opposite

mode is immediately available if desired.

Error Codes

Two error messages indicate problems with the thermostat’s operation. If the room

temperature sensor fails, the temperature display will show - -, two dashes. If there

is an internal memory failure, the temperature display will show E4. The remedy for

each of these is to replace the thermostat.

Table 1 shows the thermostat outputs for each available stage of heating or cooling.

It may be useful in checkout or troubleshooting.

2

3

Table 1 – Outputs

Equip

Config

Tstat

Model

COOL

STG 1

COOL

STG 2

HEAT

STG 1

HEAT

STG 2

HEAT

STG 3

EM HEAT

T 2 --- PA C

T 2 --- N A C

T 2 --- P H P

T 2 --- N H P

SS AC

Y

W

Y

--- ---

Opt 1 = AC

--- ---

SS HP

Opt 1 = HP

RVS = O

T 2 --- P H P

T 2 --- N H P

Y,

O/B

Y,

W

--- ---

W

Opt 10 = C

SS HP

Y,

Opt 1 = HP

RVS = B

T 2 --- P H P

T 2 --- N H P

Y,

O/B

Y

--- ---

W,

--- ---

W

--- ---

W

O/B

Opt 10 = H

2

SPD AC

T 2 --- P H P

T 2 --- N H P

Y1,

Y

Y1

W

--- ---

Opt 1 = A2

2

SPD HP

Y1,

Y,

O/B

Y1,

Y,

W

Opt 1 = H2

RVS = O

T 2 --- P H P

T 2 --- N H P

Y1,

O/B

Y1,

Y

Y1

Opt 10 = C

2

SPD HP

Y1,

Y,

Y1,

Y,

O/B

Opt 1 = H2

RVS = B

T 2 --- P H P

T 2 --- N H P

Y1,

Y

Y1,

O/B

Y1

W

W,

Opt 10 = H

O/B

T 2 --- P H P

T 2 --- N H P

T 2 --- P A C

T 2 --- N A C

Heat Only

Opt 1 = H

--- ---

W

--- ---

Cool Only

Opt 1 = C

T 2 --- PA C

T 2 --- N A C

Y

--- ---

Cool Only

Opt 1 = C

T 2 --- P H P

T 2 --- N H P

Y1

Y1,Y

2

4

WIRING DIAGRAMS

W

Y1

Y/Y2

G

Y

G

R

Y

R

*

Rh

Rc

C

COM

C

*

C wire not needed for batteries

* Remove jumper when using split power (Indoor and Outdoor units

utilize separate transformers).

A12246

Fig. 5 - Single Speed A/C Thermostat Typical Installation

2

5

WIRING DIAGRAMS (cont.)

Y1

Y/Y2

*

C wire not needed for batteries

* Remove jumper when using split power (Indoor and Outdoor units

utilize separate transformers).

A12238

Fig. 6 - Single Speed HP Thermostat Typical Installation

2

6

WIRING DIAGRAMS (cont.)

Single-Stage

Furnace

Single-Stage

Air Conditioner

Thermostat

Heat

O/B

W

Y1

Y/Y2

G

Cool

Fan

Y

G

R

Y

R

2

4VAC Hot Heating

Rh

2

4VAC Hot Cooling

Rc

*

24VAC Common

C

COM

*

Indicates connection may not be required/available.

A09246

Fig. 7 - Single-stage Furnace with Air Conditioner and Split Power

NOTE: Rc/Rh jumper is cut or removed on the thermostat.

2

7

WIRING DIAGRAMS (cont.)

Furnace

Air Conditioner

Thermostat

Heat Stage 2 (NA)

Heat Stage 1

Cool Stage 1

Cool Stage 2

Fan

O/B

W

W2

W/W1

Y1

Y/Y2

G

Y1

Y/Y2

G

Y/Y2

*

2

4VAC Hot Heating

Rh

Rc

R

C

2

4VAC Hot Cooling

DHUM

COM

24VAC Common

C

*

Remove jumper when using split power (Indoor and Outdoor units

utilize separate transformers).

A12240

Fig. 8 - Variable Speed, Step Modulating, Multi-Stage and Single-Stage

Furnace with 2-Stage Air Conditioner

2

8

WIRING DIAGRAMS (cont.)

Thermostat

Furnace

Heat Pump

O

RVS Cooling

O/B

W2

W/W1

Y1

Heat Stage 3 (furnace)

Heat/Cool Stage 1

Heat/Cool Stage 2

Fan

W

Y1

W2*

Y1

Y/Y2

G

Y/Y2

G

Y/Y2

*

2

4VAC Hot Heating

Rh

Rc

R

C

2

4VAC Hot Cooling

DHUM

COM

24VAC Common

C

*

Some heat pumps may designate W1.

*Remove jumper when using split power (Indoor and Outdoor Units

utilize separate transformers).

A12241

Fig. 9 - Variable Speed, Multi-Stage, Stage Modulating and Single-Stage

Furnace with 2-Stage Heat Pump

2

9

WIRING DIAGRAMS (cont.)

Thermostat

Fan Coil

Air Conditioner

O

Remove J2

Jumper for

heat staging

Heat Stage 2

Heat Stage 1

Cool Stage 1

Cool Stage 2

Fan

O/B

W

W2

W1

Y1

Y2

Y/Y2

G

Y/Y2

G

*

2

4VAC Hot Heating

Rh

Rc

R

2

4VAC Hot Cooling

24VAC Common

C

*

Remove jumper when using split power (Indoor and Outdoor units

utilize separate transformers).

A12242

Fig. 10 - FV/FK Fan Coil w/2-Stage Air Conditioner

3

0

WIRING DIAGRAMS (cont.)

Thermostat

Fan Coil

Heat Pump

O

RVS Cooling

Heat Stage 3

Heat/Cool Stage 1

Heat/Cool Stage 2

Fan

O/B

W

W1

W2

Y1

W1

Y1

Y/Y2

G

Y/Y2

G

Y/Y2

*

2

4VAC Hot Heating

Rh

Rc

R

C

2

4VAC Hot Cooling

24VAC Common

C

*

Remove jumper when using split power (Indoor and Outdoor units

utilize separate transformers).

A12243

Fig. 11 - FV/FK Fan Coil w/2-Stage Heat Pump

3

1

THERMOSTAT CONFIGURATION RECORD

Installer

Model Number

Date

_

________________________

_____________________________ _______________________

A. Hardware Configuration

_________ Seal Hole In Wall

B. Mode Settings

_

_________

Mode (Off, Heat, Cool, Auto, Em Heat)

Heating Setpoint Value

Cooling Setpoint Value

Fan (Auto or On)

C. Home, Away, Sleep Settings

Heat Cool

Home

_

___ ____

Away

Sleep

D. Schedule (For Programmable Thermostats)

Period 1 Period 2

Period 3

Period 4

Time Heat Cool Time Heat Cool Time Heat Cool Time Heat Cool

____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____

All

Days

Week---

days

Week---

end

3

2

E. Configuration Options

____ Equipment Type

Option 01

Option 03*

Option 04

Option 07

Option 10

Option 11

Option 12

Option 13

Option 15

Option 16

Option 17

Option 18*

Option 21*

Option 24*

Option 25*

Option 26

Option 27

____ Fahrenheit/Centigrade Selection

____ Fan (G) on with W/W1 Selection

____ Zoning

____ Reversing Valve

____ Minimum Deadband Between Heating and Cooling Setpoints

____ Smart Recovery (programmable models only)

____ Room Air Temperature Offset Adjustment

____ Auto Changeover Availability

____ Cycles Per Hour

____ Time Between Equipment Stages

____ Backlight Configuration

____ Keypad Lockout

____ Programmable / Non---Programmable (programmable models only)

____ Number of Programmable Periods Per Day (programmable models only)

____ Minimum Cooling Setpoint

____ Maximum Heating Setpoint

*

Options with an asterisk can also be set/changed by the homeowner.

3

4

3

5

3

6

R e p l a ce s: IIT2 --- PA C --- 0 4

I I T 2 --- P A C --- 0 5

Edition Date: 05/12

Manufacturer reserves the right to change, at any time, specifications and designs without notice

and without obligations.

White Rodgers 6WY24 Thermostat User Manual

Honeywell RLV310 Thermostat User Manual

Lennox CBX40UHV02 Thermostat User Manual

White Rodgers 1F95W 80 Thermostat User Manual

Honeywell TL7135A Thermostat User Manual

Honeywell T7300D Thermostat User Manual

Carrier TM004 014 Thermostat User Manual

Honeywell TG511 Thermostat User Manual

Carrier 4850HJ004 024 Thermostat User Manual

Honeywell RTH2510B1000E1 Thermostat User Manual