IꢀSTꢁllꢂR SꢂTꢃP
IꢀSTꢁllꢂR SꢂTꢃP FꢃꢀꢆTIOꢀS
Available option and default settings vary by thermostat.
®
®
FocusPRO 6000 Series
FocusPRO 5000 Series
Table 1. Installer Setup
Table 1. Installer Setup
Setup functions
Setting & Options
Setup functions
Setting & Options
1.
To begin, press and hold the s and FAN buttons until
1.
To begin, press and hold the s and FAN buttons until
(factory default in bold)
(factory default in bold)
the display changes.
the display changes.
1
System type
0
1
1 heat / 1 cool Conv.
1 heat / 1 cool heat
pump (no Aux. heat)
Heat only (2-wire, 3-wire
zone valves [Series 20],
and normally open zone
valves)
8
Emergency heat
cycle rate
9
1
3
Electric emergency heat
Steam or gravity
Hot water systems or fur-
naces of 90%+ efficiency
Gas or oil furnaces of
less than 90% efficiency
[Other options: 1–12]
2
5
3
3
3
4
5
Heat only with fan
Cool only
9
1
First stage
compressor cycle
rate
Recommended
[Other options: 1–6]
2 heat / 1 cool heat
pump (with Aux. heat)
2 heat / 2 cool Conv.
2 heat / 1 cool Conv.
1 heat / 2 cool Conv.
2 heat / 2 cool heat pump
0
Second stage
compressor cycle
rate
Recommended
[Other options: 1–6]
6
7
8
9
2.
Press s or t to change settings.
2.
Press s or t to change settings.
12
Manual/Auto
changeover
0
1
2
Manual changeover
(Heat/Cool/Off)
Auto changeover (Heat/
Cool/Auto/Off)
(no Aux. heat)
Function
Setting
Function
Setting
10
3 heat / 2 cool heat
pump (with Aux. heat)
Auto changeover only
2
3
Changeover valve
0
1
Controls valve in cooling
Controls valve in heating
(Auto)
(O/B terminal)
13
Adaptive Intel-
ligent Recovery
1
0
On
Off
Fan control
(heating)
0
Gas/Oil heat (equipment
controls heating fan)
Electric furnace (thermo-
stat controls heating fan)
TM
0
0
1
1
1
14
15
Temperature
display
0
1
Fahrenheit
Celsius
Done
Next
Done
Next
5
First stage heat
cycle rate
5
Gas or oil furnaces of
less than 90%
Compressor
protection
5
5-minute compressor
off time
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
efficiency
Steam or gravity
Hot water systems or fur-
naces of 90%+ efficiency
Electric furnaces
[Other options: 0–4
minutes]
1
3
3.
4.
5.
Press NEXT to advance to the next function.
Press DONE to exit and save settings.
Proceed to Installer Setup Functions on page 4.
3.
4.
5.
Press NEXT to advance to the next function.
Press DONE to exit and save settings.
Proceed to Installer Setup Functions on page 4.
1
6
Schedule format
0
5/2 (weekdays
and weekends
programmable)
5/1/1 (weekdays,
Saturday, and Sunday
programmable)
Automation and Control Solutions
9
Honeywell International Inc.
[
Other options: 1–12]
1
1
985 Douglas Drive North
6
7
Second stage
heat/Aux heat
cycle rate
5
Gas or oil furnaces of
less than 90% efficiency
Steam or gravity
Hot water systems or fur-
naces of 90%+ efficiency
Electric furnaces
Golden Valley, MN 55422
1
3
2
6
7
Auxiliary heat
control
0
1
Comfort
Economy
2
Heat temperature 90
range stops
Max. heat temperature
setting is 90°F (32°C)
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
9
[
Other options: 1–12]
[
(
Other options: 40–89°F
4.5°C to 32°C)]
Auxiliary heat
cycle rate
5
Gas or oil furnaces of
less than 90% efficiency
Steam or gravity
Hot water systems or fur-
naces of 90%+ efficiency
Electric furnaces
Toronto, Ontario M1V 4Z9
28
Cool temperature 50
range stop
Min. cool temperature
setting is 50°F (10°C)
1
3
[
(
Other options: 51–99°F
10.5°C to 37°C)]
® U.S. Registered Trademark
9
© 2006 Honeywell International Inc.
US Patent No. 6595430, D509151; other
Patents Pending. All Rights Reserved
69-2026 M.S. 09-06
[
Other options: 1–12]
Functions 13 and 16 only available on the 6000 series;
function 26 only available on the 5000 series
2
3
4
5