Honeywell L6006 Thermostat User Manual

L4006,7,8; L6006,7,8

Aquastat Controllers

PRODUCT DATA

FEATURES

FOR VERTICAL

MOUNTING AND

HORIZONTAL

SENSOR

•

L4006, 7, and 8 provide Spst switching for high or low

limit or circulator control.

L4006G includes two Spst switches that provide high

limit and circulator control.

INSERTION

L4006,7; L6006,7 models are available for insertion in:

vertical or horizontal immersion well, vertical or

horizontal direct immersion, and surface mounting.

•

L4008, L6008 include remote bulb for mounting

controller at a location away from the sensing element.

Totally enclosed Micro Switch™ snap-acting switches

operate on temperature rise to set point.

Models calibrated for high limit use are also suitable

for low limit control if a separate high limit controller

is used.

•

Visible control point scale and external adjustment

screw, permit easy setting.

FOR SURFACE

MOUNTING

WITH REMOTE BULB

Remote bulb models may be used to sense air

temperature in ducts and in outside air sensing

applications.

GENERAL

Aquastat^®Controllers are immersion type devices for limiting

or regulating the temperature of liquids in boilers, storage

tanks, and other applications where temperature control is

required.

Contents

General .............................................................................

Features ...........................................................................

Specifications ...................................................................

Ordering Information ........................................................

Installation ........................................................................

Operation .......................................................................... 14

Adjustments ...................................................................... 15

Checkout .......................................................................... 17

Material Safety Data Sheet .............................................. 18

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

SPECIFICATIONS

IMPORTANT

NOTE: The following specifications are standard. Variances,

available as options, are listed in Tables 1 and 2.

The specifications given in this publication do not

include normal manufacturing tolerances. Therefore,

this unit may not exactly match the listed

specifications. Also, this product is tested and

calibrated under closely controlled conditions, and

some minor differences in performance can be

expected if those conditions are changed.

Electrical Ratings (A):

Models with 2° F (1° C) fixed differential:

120 Vac

240 Vac

Full Load

2.6

1.3

7.8

Locked Rotor

15.6

SUPER TRADELINE /TRADELINE MODELS

SUPER TRADELINE controls offer features not available on

TRADELINE or standard models, and are designed to replace

a wide range of Honeywell and competitive controls.

Models with 5° F (3° C) fixed differential or 5° F to 30° F

(3° C to 17° C) adjustable differential:

10/120 Vac 200/240 Vac

277 Vac^a

4.2

25.2

TRADELINE models are selected and packaged to provide

ease of stocking, ease of handling, and maximum

replacement value. Specifications of SUPER TRADELINE

and TRADELINE controls are the same as those of standard

models except as noted below.

Full Load

8.0

5.1

Locked Rotor 48.0

30.6

Millivoltage 0.25 at 0.25 to 12 Vdc

L6008G only.

SUPER TRADELINE Model: L6006A Aquastat Controller.

Switching:

L4006, L4007, L4008: Spst.

L6006, L6007, L6008: Spdt (breaks R-B and makes R-W on

temperature rise at setpoint).

SUPER TRADELINE Features:

SUPER TRADELINE package with cross reference label and

special instructions.

Factory-set stop at 240° F (116° C).

Vertical or horizontal mount.

Tube of heat-conductive compound.

Insulation: 1-1/2 in. to 3 in. (38 mm to 76 mm).

Pressure Rating:

Capillary Bulb (Direct Immersion): 200 psi (1379 kPa).

Immersion Well: 255 psi (1758 kPa).

Sensing Bulb Material: Copper.

TRADELINE Models: L4006A,B,E; L4008E; L6006C;

L6008A Aquastat Controllers.

Sensing Bulb Fill: Liquid—toluene or silicone oil.

TRADELINE Features Available:

TRADELINE package with cross reference label and special

instructions.

Sensing Bulb Dimensions: 2-7/8 in. (73 mm) long,

3/8 in. (10 mm) diameter.

Some TRADELINE models include immersion well.

Factory-set stops at 180° F, 240° F, or 250° F (82° C, 116° C,

or 121° C).

Wiring: Screw terminals.

Maximum Ambient Temperature: 150° F (66° C).

Vertical or horizontal mount.

Tube of heat-conductive compound.

Insulation depths of 1-1/2 in. or 3 in. (38 or 76 mm).

ORDERING INFORMATION

When purchasing replacement and modernization products from your TRADELINE wholesaler or distributor, refer to the

TRADELINE^®Catalog or price sheets for complete ordering number.

If you have additional questions, need further information, or would like to comment on our products or services, please write or

phone:

Your local Honeywell Automation and Control Products Sales Office (check white pages of your phone directory).

Honeywell Customer Care

885 Douglas Drive North

Minneapolis, Minnesota 55422-4386

In Canada—Honeywell Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V 4Z9.

International Sales and Service Offices in all principal cities of the world. Manufacturing in Australia, Canada, Finland, France,

Germany, Japan, Mexico, Netherlands, Spain, Taiwan, United Kingdom, U.S.A.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Approvals:

Underwriters Laboratories Inc:

(25)

Remote bulb devices and well-mounted devices shipped

without well are component recognized:

File No. MP466, Guide No. MBPR2.

L4006A shipped with well, L4006G, L4007A,B; L6006C for

surface mounting, L6006B for direct immersion mounting,

and L6007A are listed: File No. MP466, Guide No. MBPR.

L6008G is listed: File No. E4436, Guide No. XAPX.

Canadian Standards Association: File No. LR1620,

Guide No. 400-E-O.

KNOCKOUT FOR 3/4 (19 )

/16

CONDUIT ON ALL MODELS. SIMILAR

KNOCKOUT ON BOTTOM FOR

HORIZONTAL INSERTION AND

REMOTE BULB MODELS.

(

(51)

3/16

2-1/8 (54)

(

ANSI Miswiring: Models with 1/4 in. (6.35 mm) tab terminal

meet ANSI Appliance Miswiring Standard.

Mounting:

Horizontal and vertical models mount directly to an immersion

well installed in a boiler fitting. L4006H and L6006C contain

a bracket and clamp for surface mounting on the pipe or

tank. Remote bulb models have three mounting holes

in rear of case for screw mounting to a vertical surface.

The L6006B direct immersion model also mounts directly to

a boiler fitting.

-5/8

(

136)

RESET

BUTTON

(L4006E,

L4008E

ONLY)

Finish: Gray.

1-7/8

48)

(

19)

Dimensions:

(19)

Installation: (See Figures 1, 2, and 3).

Immersion Well: (See Fig. 4).

Boiler Fitting and Bulb: (See Fig. 5).

ELEMENT

FOR VERTICAL

IMMERSION

KNOCKOUT FOR 3/4 (19)

CONDUIT ON VERTICAL

INSERTION MODELS ONLY

1/16

(18)

ELEMENT FOR HORIZONTAL IMMERSION

M8957A

Accessories and Parts:

37536A Scale Lock Assembly: Includes one 137536-767

Scale Lock and one 80844C-767 Screw, No. 3-48 x 3/16

Fig. 1. Approximate case installation dimensions

in inches (mm) for direct insertion models.

(

5 mm).

Q615A1004 Weatherproof Enclosure (for remote bulb devices

only).

ALTERNATE POSITION

OF SENSING ELEMENT

CAPILLARY

107408 Heat-Conductive Compound (4-oz. can).

104488 Spring Clip (stainless steel).

124904 Well Adapter.

Immersion Well Assemblies and Compression Fittings:

See form no. 68-0040, Wells and Fittings for Temperature

Controllers, for list and ordering information.

4-3/16

(106)

MOUNTING

HOLE FOR

/16 IN. (5 MM)

SCREW (3)

3/64

5) (3)

(

5/16

24)

(

/8 (10)

1-1/4

32)

(

ALTERNATE POSITION

OF SENSING ELEMENT

SENSING

ELEMENT

CAPILLARY

M8823

Fig. 2. Approximate installation dimensions

in inches (mm) for remote bulb models. Other

dimensions are the same as Fig. 1.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

/2 — 14 IN. NPT

/8 IN. (22 MM)

STANDARD

/16

KNOCKOUT (2)

(

11)

M8789A

-1/2 (38)

3 (76)

25)

(

Fig. 4. Approximate immersion well dimensions in inches

(mm) for all models except L4006C and L6006B.

/2 OR 3/4 — 14 IN. NPT

(

10)

-5/8

(

136)

1-5/16 (33)

3 (76)

M8799A

Fig. 5. Approximate boiler fitting and bulb dimensions

in inches (mm) for L4006C and L6006B.

(51)

-3/4 (70)

M8958A

Fig. 3. Approximate installation dimensions

in inches (mm) for surface mount models.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Standard Models:

L4006,A,B,C,E,G; L4007,A,B; L4008A,B.E; L6006A,B,C; L6007A, L6008,A,G,H

Table 1. L4006, L4007, L4008 Controller (SPST Switching) Specifications.

Midscale

Differential

°F (°C)

Switching On

Temperature

Rise

Range

°F (°C)

Model

Application

Insertion^a

Available Options

L4006A

High or low 40° F to 180° F

2° F or 5° F fixed Horizontal

(1° C or 3° C)

Breaks

—

TRADELINE models

available.

NPT brass spud 1/2 in. or

3/4 in.

(13 mm to 19 mm)

Special capillary assembly.

Insertion 3-3/8 in. or

limit

(4° C to 82° C)

(

00° F to 240° F 5° F to 30° F

38° C to 116° C) adjustable

3° C to 17° C)

(

—

in. (86 or 127 mm)

—

Celsius scale markings.

Factory-set stops at 160°,

80°, 185°, 200°, 220°, or

30° F (71°, 82°, 85°, 93°,

04°, or 110° C).

—

Insulation depths of

-1/2 in. , 3 in. or 4 in.

38 mm, 76 mm, or

02 mm).

(

—

Screw and mounting

brackets.

—

Plastic tubing over well.

Modified dial with stop.

Special cover and knobs.

With ground screw.

L4006B

Circulator

100° F to 240° F 5° F (3° C) fixed Horizontal

38° C to 116° C) or 5° F to 30° F

3° C to 17° C)

Makes

—

TRADELINE model

available.

Insulation depth 1-1/2 in. or

3 in.

(

—

adjustable

(

38 mm or 76 mm).

NPT brass spud 3/4 in.

19 mm)

—

(

Screw in front of case on

dial suitable for

Powerpile control.

Factory-set stop at

—

240° F (116° C).

L4006C

High or low 65° F to 200° F

3-1/2° F (2° C)

Horizontal

direct

Breaks

TRADELINE model

available.

limit

(18° C to 93° C) fixed

immersion

—

Less cover.

Capillary 10 in.

(

254 mm).

NPT brass spud 3/4 in.

19 mm).

—

(

_L₄₀₀₆_Eb

High limit

130° F to 290° F Manual reset

Horizontal or Breaks

vertical

—

TRADELINE model

available.

Insulation depth

(54° C to 141° C)

-1/2 in. or 3 in.

(38 or 76 mm).

—

NPT brass spud 1/2 in. (13

mm)

Factory-set stop at

250° F (121° C).

Capillary 8 in. (203 mm).

Some models include copper well or fitting; specify when ordering. Also specify boiler tapping size 1/2 or 3/4 in.

13 to 19 mm) NPT and insulation depth.

(

Manual reset (trip-free) switch breaks circuit and locks out when controlled medium reaches setpoint. Controlled temperature

must drop 20° F (11° C) below setpoint before contacts can be manually reset.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Table 1. L4006, L4007, L4008 Controller (SPST Switching) Specifications. (Cont.)

Midscale

Differential

°F (°C)

Switching On

Temperature

Rise

Range

°F (°C)

Model

Application

Insertion^a

Available Options

L4006G

High limit

and

circulator

control

100° F to 200° F 10° F (6° C) fixed Horizontal

(38° C to 93° C)

Two switches

break

simultaneously

—

External adjustment knob.

Insulation depth 4 in.

(102 mm).

—

Factory-set stop at

60° F (71° C).

—

Celsius scale markings.

Without well.

L4007A

High or low 100° F to 240° F 2° F or 5° F

Horizontal or Breaks

vertical

—

Insulation depth

1-1/2 in. or 3 in.

(38 mm or 76 mm).

limit

(38° C to 116° C) (1° C or 3° C)

fixed,

° F to 30° F

3° C to 17° C)

adjustable

(

L4007B

L4008A

Circulator

100° F to 240° F 5° F (3° C) fixed Vertical

38° C to 116° C) or

° F to 30° F

3° C to 17° C)

Makes

—

Celsius scale markings.

(

adjustable

High or low 100° F to 240° F 5° F (3° C) fixed, Remote bulb Breaks

limit

—

Remote capillary

5-1/2 ft (1.7 m),

8-1/2 ft (2.6 m) or

10 ft (3.0 m).

Factory-set scale stops at

(38° C to 116° C) 5° F to 30° F

or (3° C to 17° C)

30° F to 270° F adjustable

54° C to 132° C)

direct

immersion

(

20°, 170°, or 200° F (49°,

77°, or 93° C)

—

Celsius scale markings.

Front cover screw.

L4008B

_L₄₀₀₈_Eb

Circulator

High limit

100° F to 240° F 5° F (3° C) fixed Remote bulb Makes

—

Capillary 5-1/2 ft

(1.7 m).

(

38° C to 116° C) or

° F to 30° F

3° C to 17° C)

direct

immersion

(

adjustable

40° F to 80° F

Manual reset

Remote bulb Breaks

—

Factory-set scale stops at

140°, 200°, or 250° F (60°,

93°, or 121° C).

(

4° C to 27° C) or

30° F to 270° F

54° C to 132° C)

Capillary 5-1/2 ft or

20 ft (1.7m or 6.1 m).

Some models include copper well or fitting; specify when ordering. Also specify boiler tapping size 1/2 or 3/4 in.

13 to 19 mm) NPT and insulation depth.

(

Manual reset (trip-free) switch breaks circuit and locks out when controlled medium reaches setpoint. Controlled temperature

must drop 20° F (11° C) below setpoint before contacts can be manually reset.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Table 2. L6006, L6007, L6008 Controller (SPDT Switching) Specifications.

Midscale

Differential

°F (°C)

Range

°F (°C)

Model

L6006A

Application

Insertion^a

Available Options

Circulator and low 100° F to 240° F

5° F (3° C) fixed Horizontal

—

SUPER TRADELINE model

available.

limit or high limit

(38° C to 116° C)

5° F to 30° F

(3° C to 17° C)

adjustable

—

Modified dial with stop.

NPT brass spud 1/2 in. or 3/4

in. (13 mm to 19 mm)

3-3/8 in. (86 mm) insertion.

Without well.

Adapter for horizontal or

vertical mount.

00° F to 290° F

38° C to 143° C)

(

—

Insulation depth 1-1/2 in. or

in. (38 mm or 76 mm).

L6006B

L6006C

Circulator and low 100° F to 240° F

limit or high limit (38° C to 116° C)

5° F (3° C) fixed Horizontal

—

Direct immersion.

Insulation depth 1-1/2 in.

(38 mm).

3/4 in. (19 mm ) brass

compression fitting.

° F to 30° F

3° C to 17° C)

adjustable, or

0° F (17° C)

(

—

fixed.

Circulator, low limit, 65° F to 200° F

and high limit (18° C to 93° C)

5° F (3° C) fixed Horizontal or

—

TRADELINE model available.

Strap-on, surface mount.

° F to 30° F

3° C to 17° C)

vertical surface

mounted

(

adjustable

L6007A

L6008A

Circulator and low 40° F to 180° F

limit or high limit (4° C to 82° C)

Fixed

Horizontal or

vertical

—

Insulation depth 1-1/2 in. or 3

in. (38 mm or 76 mm).

Circulator and low 100° F to 240° F

5° F (3° C) fixed Remote bulb

5° F to 30° F

(3° C to 17° C)

TRADELINE models

available.

Modified dial with stop.

Capillary 5-1/2 ft (1.7 m).

limit cooling

(38° C to 116° C)

—

-30° F to +70° F

(

-35° C to +21° C) adjustable

3-1/2° F (2° C) Remote bulb

Controller to cycle (54° C to 110° C) or fixed

L6008G

L6008H

Two-stage Aquastat 130° F to 230° F

—

Capillary 6 ft (1.8 m).

Adjustable interstage

differential; 5° F to 10° F

(2° C to 6° C).

two-stage gas

valve.

60° F to 160° F (16°

C to 71° C)

Low fire Aquastat

Controller

150° F to 200° F

(66° C to 93° C)

15° F (8° C)

fixed

Remote bulb

—

Capillary 33 in. (0.8 m).

(maximum

temperature

of element

405° F

(

207° C))

Some models include copper well or fitting; specify when ordering. Also specify boiler tapping size 1/2 or 3/4 in. NPT and

insulation depth.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

The manufacturer usually provides a tapping for insertion of

the controller sensing element. This tapping is located at a

point where typical water temperature can be measured.

Depending on the model, the element is inserted in an

immersion well, through a boiler fitting, or directly immersed.

INSTALLATION

When Installing This Product…

Read these instructions carefully. Failure to follow them

could damage the product or cause a hazardous

condition.

Check the ratings given in the instructions and on the

product to make sure the product is suitable for your

application.

Installation should be made by a qualified service technician.

Follow the instructions furnished by the system manufacturer, if

available. Otherwise, refer to appropriate procedure listed

below.

Installer must be a trained, experienced service

technician.

After installation is complete, check product operation as

provided in these instructions.

Mounting Immersion Well and Direct

Immersion Models (L4006A,B,C,E,G;

L4007A,B; L6006A,B; L6007A)

WARNING

Can cause serious injury, death or property

damage.

This product is intended for use only in systems with a

pressure relief valve.

Installing Immersion Well Models

Explosion Hazard.

(

L4006A,B,E,G; L4007A,B; L6006A; L6007A)

On an existing installation, shut off the power and remove the

old control. If the old immersion well appears suitable, and if

the adapter clamp on the Aquastat Controller fits the old well

spud, this well does not need to be replaced.

To replace the well:

WARNING

Can cause serious injury or death.

Disconnect power supply before beginning installation

to prevent electrical shock or equipment damage.

If the system is filled, drain the system to a point below

the boiler tapping.

Electrical Shock Hazard.

2. Remove the old well from the boiler tapping.

3. Install the immersion well included with the controller. If

the boiler tapping is greater than 1/2 in. (13 mm), use a

reduction fitting to adapt the boiler opening to the 1/2 in.

(

13 mm) threads that are standard with the well or fitting.

Fittings with 3/4 in. (19 mm) threads are also available.

Fill the system. Make sure that the well is screwed in

tightly enough to prevent leakage. Do not use the case

as a handle to tighten the well after the controller is

secured to the well.

CAUTION

Equipment Damage Hazard.

Use of incorrect device or improper installation can

damage the system.

. Do not replace immersion-type Aquastat Controller

with strap-on Aquastat Controller.

To install the controller:

Loosen the screw (at the top of the case, above the

scale setting), and remove the cover. Loosen the two

screws that secure the adapter clamp. (See Fig. 6).

Insert the sensing element into the immersion well.

Fasten the case of the Aquastat Controller to the well

with the adapter clamp. Make certain that the clamp is

properly positioned over the groove of the well spud.

Also, be sure the flange at the opening of the well fits

snugly into the opening of the case. The sensing bulb

must bottom in the well.

2. Do not secure draw nut so tightly that retainer clamp

can collapse tubing.

IMPORTANT

. Terminals on these Aquastat relays are approved for

copper wire only.

. Controller may be used with or without immersion

well. If used, well must snugly fit sensing bulb for best

thermal response. Insert bulb until it rests against the

bottom of the well. Use well of correct length and

bend the tubing, if necessary, to provide enough force

to hold the bulb against the bottom of the well. Avoid

making a sharp bend in the tubing as it can produce a

break in the tubing and cause loss of fill. This

condition causes the High and Low Limit controls to

be made continuously.

NOTE: Some models include up to 3 in. (76 mm) extra capil-

lary tubing inside the case. In these models, pull out

the extra tubing, if needed.

. If well does not snugly fit on bulb, use the heat-

conductive compound, included with Super Tradeline

and Tradeline models, as follows: Fold the plastic bag

of compound lengthwise and twist gently. Snip the

end of the bag and insert into the well. Slowly pull out

the bag while squeezing firmly to distribute compound

evenly in the well. Insert the bulb into the well. Bend

the tubing, if necessary, to provide force to hold the

bulb against the bottom of the well and to hold the

outer end of the bulb firmly in contact with the side of

the well. Wipe off excess compound.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Insert the immersion sensing bulb through the bulb

compression fitting. Adjust the adapter clamp so that the

clamp fits over the groove at the opening of the bulb

compression fitting.

Tighten the adapter clamp screws so that the Aquastat

Controller is firmly attached to the bulb compression

fitting.

SETPOINT

INDICATING DIAL

DIFFERENTIAL

ADJUSTMENT

WHEEL

Mounting Remote Bulb Models

ADAPTER CLAMP

SCREWS

(

L4008A,B,E; L6008A,G,H)

INSERTION

The remote temperature-sensing bulb can either be installed in

an immersion well (See Fig. 8) that extends into the boiler or

tank, or it can be directly immersed in the controlled medium

ELEMENT

(See Fig. 9). For installations that do not use a well, secure the

remote bulb with a bulb compression fitting (See Fig. 10), or

capillary compression fitting. (See Fig. 11).

WITH VERTICAL MOUNTING OF

IMMERSION WELL, ELEMENT IS

ATTACHED TO BOTTOM OF THE

CASE.

Order well, well adapter, bulb compression fitting or capillary

compression fitting separately. See form no. 68-0040, Wells

and Fittings for Temperature Controllers. If used, well must

snugly fit sensing bulb for the best thermal response. Insert

bulb until it rests against the bottom of the well. Hold it there

while tightening the tubing clamp. (See Fig. 8).

SELECT MODELS HAVE SCREW

TERMINAL, NOT TAB TERMINAL.

M8806A

Fig. 6. Internal view of L6006A.

Installing Direct Immersion Models

L4006C, L6006B)

Models that provide for direct immersion of the sensing

element into the boiler include a bulb compression fitting

assembly instead of an immersion well. Install the fitting in the

boiler tapping as follows:

The boiler manufacturer usually provides a tapping for the

insertion of the Aquastat Controller sensing element. This

tapping should be located at a point where typical water

temperature can be measured. Never locate the bulb or

protecting immersion well close to a hot or cold water inlet or a

steam coil.

(

Be sure the sealing washer is in place as shown in

Fig. 7. Make sure that the spud of the bulb compression

fitting is screwed in tightly enough to prevent leaking.

If the system is filled, drain system to a point below the boiler

tapping, or wherever the sensing bulb is to be installed.

The bulb can also be installed in the supply line of an indirect

water heater, in the direct water heater itself, or in the feed

riser, about 6 in. (153 mm) above the boiler. If the riser is

valved, the bulb can be installed between the boiler and the

valve.

ADAPTER

CLAMP

NOTE: Do not make sharp bends or kinks in the capillary.

Make bends no sharper than 1 in. (25 mm) radius.

After installing the controller, carefully coil the excess capillary

at the bottom of the controller case.

SPLIT SLEEVE

ADAPTER CLAMPS

FIT OVER

GROOVE

Mounting Immersion Well

Screw the well into the boiler, tank, or pipe tapping.

Insert the bulb in the well, pushing the tubing until the

bulb bottoms in the well.

Attach the retainer clamp to the end of the well spud.

Loosen the draw nut and spread the jaws of the clamp

with the screwdriver if necessary. (See Fig. 8).

With the retainer clamp attached to the well spud (be

sure the jaws of the clamp hook over the ridge at the end

of the spud, as shown at points A in Fig. 8), adjust the

tubing to fit through the retainer clamp groove, as shown

at point B in Fig. 8.

SEALING WASHER

BULB COMPRESSION

FITTING

M8774A

SENSING BULB

Tighten the draw nut so that the retainer clamp is firmly

attached to the well spud and the tubing is held securely

in place.

Fig. 7. Direct immersion model

with fitting partially removed.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

CLAMP B

CLAMP A

CLAMP SCREWS (2)

BULB

SEALING

BULB

COMPRESSION

FITTING

WASHER

JAWS

SPREAD JAWS

TO FIT OVER

RIDGE ON

WELL SPUD

INSERTION LENGTH

APPROX. 3-3/16 IN. (81 MM)

SCREWDRIVER

SPLIT SLEEVE

M8815A

MOUNTING CLAMP

Fig. 10. Bulb compression fitting.

Use with L4006A,B; L6008A.

DRAW

NUT

MOUNTING

CLAMP

SPUD

WELL

BULB

Place clamps A and B on the assembly so that the

sleeve is drawn into the fitting when the screws are

tightened.

TUBING

M8777A

NOTE: Make sure that the nub on clamp A engages the

space between the sleeve and the clamp.

Tighten the clamp screws evenly.

Fig. 8. Immersion well fitting.

Mounting With Capillary Compression Fitting

NOTCHES FOR

CAPILLARY

TUBE (4)

27-1/2 IN.

(70 MM)

SENSOR

Screw the fitting into the boiler or pipe tapping.

Place the packing nut on the tubing.

7/8 IN. (22 MM)

3. Slide the bulb completely through the fitting.

DIAMETER

KNOCKOUT

BOTH ENDS

Place the composition disk and four slotted brass

washers on the tubing in the order shown in Fig. 11. Turn

the brass washers so the slots are 180 degrees apart.

IMMERSION

BULB

BOILER PLUG

CAPILLARY TUBING

COMPOSITION DISK

LEFT SNAP

SWITCH

(

SLOTTED)

(

NO. 2)

0 FT. (3.0 M)

CAPILLARY

TUBE

RIGHT SNAP

SWITCH (NO. 1)

MOUNTING

HOLES (3)

M4673A

EXAMPLE OF SLOTTED WASHERS

ASSEMBLED

SELECT MODELS HAVE SIX TERMINALS.

IN PAIRS:

PACKING NUT

M8816A

Fig. 9. Internal view of L4008L or L6008G.

Fig. 11. Capillary compression fitting. Use with L4008.

Mounting With Bulb Compression Fitting

Slide the seal assembly into the fitting and tighten the

packing nut.

Screw the fitting into the boiler or pipe tapping.

Slide the sealing washer onto the bulb.

Insert the bulb into the fitting until the bulb bottoms.

Slide the split sleeve into the fitting. (See Fig. 10).

Duct Mounting

Drill a 3/4 in. (19 mm) hole in the duct wall large enough

to admit the sensing bulb into the holder.

Using the holder as a template, mark and drill holes for

the bulb holder mounting screws. (See Fig. 12).

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Mounting Remote Bulb Models

For Outdoor Air Sensing

These models have a 5 ft (1.5 m) capillary that establishes the

maximum distance between the case and the outdoor

mounting.

Install the bulb on the outside of the building in the shield

provided (See Fig. 15) where it can be exposed to

representative air temperature, but not to direct sunlight. Mount

the bulb high enough so that accumulated snow, leaves, or

other debris cannot obstruct circulation of air around it, and

where children cannot reach it. Avoid vents from the building.

M8970A

Fig. 12. Bulb support.

Break the holder to the desired length. (See Fig. 13).

Install the case at the indoor location selected, fastening the

screws through holes in the back of the case. Bring out the

bulb and tubing through a 3/4 in. (19 mm) hole in the outside

wall, avoiding sharp bends or kinks. Leave excess tubing

coiled near the case. Do not make sharp bends near the case

or bulb.

NOTE: The holder must be long enough to hold the sensing

bulb in freely circulating air away from the duct wall.

Neatly coil the excess capillary at the controller case

or at the bulb holder.

Slip the bulb through the supports in the shield. Pinch the split

supporting clip until it holds the bulb firmly in position. If the

seal-off tube protrudes from under the shield, bend it under as

shown in Fig. 15.

Hold the shield over the mounting position and form a small-

radius bend in the tubing. Place the split plug around the tubing

and move the shield into the mounting location as a unit. Push

the split plug into the hole until it is wedged securely in place.

Fasten the shield in place on the wall with the screws provided.

M7216A

NOTE: If the tubing is properly shaped and the split plug

installed as directed, the shield will cover the split

plug, and the hole in the wall will be hidden from sight.

Fig. 13. Removing excess bulb support.

SPLIT WOOD PLUG

/4 IN.

INSERT BULB

IN CLAMP

(

19 MM)

HOLE IN

WALL

PINCH TOP EDGES OF

HOLDER TOGETHER

AT EACH SEGMENT

OUTDOOR

SENSING

BULB

CAPILLARY

TUBING

SENSING

BULB

CAPILLARY

TUBING

SEAL-OFF

TUBE

BE SURE EXTENSION TUBE IS

UNDER BULB HOLDER, AS SHOWN

M7217A

4886A

BULB

Fig. 14. Securing capillary in bulb holder.

SHIELD

M8800A

Place the capillary in the bulb holder channel. Pinch the

top edges of the holder together at each segment. (See

Fig. 14).

Insert the bulb holder into the controlled area through the

hole prepared in step 1.

Fasten the bulb holder to the duct wall with the screws

provided.

Fig. 15. Mounting bulb in shield outside building.

Mounting L6008A Remote Bulb Controller

Mounting with Guard Bracket

Mount the bulb in the guard bracket as shown in Fig. 16.

Locate the bulb and bracket combination, in freely circulating

air, in the controlled area. With screws provided, fasten the

bracket in place.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Mounting on Suction Line

Wiring

In cooling units with more than one suction line, place

the sensing bulb on the common line.

Make certain the bulb is at least 2 ft (0.6 m) from the

point at which the suction line leaves the cooler. This

prevents the outside temperature from being transmitted

to the remote bulb through the copper tubing of the

suction line.

Place the remote sensing bulb on the side of the

horizontal suction line between the coil and trap (not on

the trap).

Disconnect power supply before beginning installation to

prevent electrical shock or equipment damage.

All wiring must comply with local codes and ordinances

regarding wire size, type of insulation, enclosure, etc.

Figures 19 through 28 show typical hookups.

When wiring a switch equipped with a 1/4 in. (19 mm) tab

terminal connector, use 18 AWG to 22 AWG (0.8 mm to

Attach the sensing bulb to the suction line with clips or

straps. (See Fig. 17).

Coil the excess length of capillary tubing near the

L6008A case.

.3 mm ) gauge wire with an AMP Inc. part no. 2-520129-2

fully insulated flag receptable connector or equivalent.

ENCLOSED

SENSING BULB

SUPPORTING

CLIP

PIPE

2 IN.

ADJUSTABLE

PIPE

STRAP

MOUNTING

BRACKET

SENSOR

M8791A

Fig. 16. Securing remote bulb in clip

when mounting with guard bracket.

SUCTION LINE

LEAVES

COOLER

WALL

SUCTION

LINE

AQUASTAT

CONTROLLER CASE

COIL

M8771B

L6008A

CIRCULATOR

LOW LIMIT

CONTROLLER

Fig. 18. Mounting L4006H or L6006C directly on surface.

4 VOLT

CAPILLARY

REMOTE

BULB

BULB CLIPS

TO SUCTION LINE

M8805A

THERMOSTAT

LOW WATER

CUTOFF

PRESSURE

CONTROL

Fig. 17. Attaching remote bulb to horizontal suction line.

(

HOT)

Mounting Surface Mount Models

L4006A OR

L4007A

The L4006H and L6006C are designed for surface mounting

on piping or tanks. Mount the controller directly on the tank

surface using the adjustable mounting bracket as shown in

Fig. 18. The controller can be mounted in any position.

LOW LIMIT

AQUASTAT

GAS

VALVE

PILOTSTAT

CONTROL

CONTROLLER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

When mounting the L4006H or L6006C on piping, the pipe

should be 1 in. (25 mm) diameter or larger for accurate

temperature sensing. Remove any insulation from the pipe.

Thoroughly scrape off all scale, rust, or paint. Mount the

controller using adjustable bracket provided. Turn on power.

USE L4006E FOR MANUAL RESET.

M2856B

Fig. 19. Typical gas-fired system with domestic hot water.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

PROTECTORELAY

CONTROL

24 VOLT

THERMOSTAT

L4006A OR L4007A

HIGH LIMIT

(

HOT)

RA832A

(HOT)

L4006A OR L4007A HIGH

LIMIT CONTROLLER

SWITCHING RELAY

AQUASTAT

CONTROLLER

4 VOLT

THERMOSTAT

IGNITION

CIRCULATOR

L4006B OR L4007B

CIRCULATOR

AQUASTAT

BURNER

MOTOR

OIL VALVE

(IF USED)

CONTROLLER

BURNER

POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

M1054B

L4006A OR L4007A LOW LIMIT

AQUASTAT CONTROLLER

Fig. 20. Typical oil-fired gravity system.

PROTECTORELAY

CONTROL

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND

OVERLOAD PROTECTION AS REQUIRED.

HOT)

(

USE L4006E FOR MANUAL RESET.

M2855B

INDICATING

LIGHT

COOLING

EQUIPMENT

Fig. 23. Typical oil-fired hydronic heating system that

provides year-round domestic hot water using RA832A.

L6008A

CIRCULATOR AND

LOW LIMIT

POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

CONTROLLER

M8780A

4V THERMOSTAT

BURNER MOTOR

L4008A OR E

HIGH LIMIT

RA817A

PROTECTORELAY

Fig. 21. L6008A used to control cooling

equipment and indicating light.

CONTROLLER CONTROL

RA89A RELAY

PROTECTORELAY

24V

THERMOSTAT

CONTROL

HIGH LIMIT

CONTROLLER

CIRCULATOR

AND LOW

IGNITION

LIMIT CONTROL

IGNITION

TRANSFORMER

CIRCULATOR

SWITCHING RELAY

(HOT)

L6008A CIRCULATOR

LOW LIMIT CONTROLLER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

CIRCULATOR

(

HOT)

SELECT MODELS HAVE 1/4 IN. (6) TAB TERMINAL FOR W TERMINAL.

M8785B

BURNER

MOTOR

LINE VOLTAGE

LOW VOLTAGE

Fig. 24. Typical connection diagram for an oil-fired,

hydronic heating system that provides year-round

domestic hot water using RA817A.

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

L6006C USED AS HIGH LIMIT CONTROL.

L6006C USED AS AN OPERATING CONTROL.

R-B OPENS, R-W CLOSES ON TEMPERATURE RISE.

M8960B

Fig. 22. Typical oil-fired hydronic

system with domestic hot water.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

L4006

HIGH LIMIT

(HOT) L2

SERIES 80

THERMOSTAT

CONTROLLER

MILLIVOLTAGE

THERMOSTAT

L6006

CIRCULATOR

AND

LOW LIMIT

CONTROL

MILLIVOLTAGE

VALVE OPERATOR

SAFETY

SHUTOFF

PILOTSTAT¨

POWER UNIT

OPERATOR PILOT

COIL

BURNER

M1156A

L8148A

POWER UNIT COIL

C1 C2

Fig. 27. Typical Powerpile System wiring diagram.

LOW VOLTAGE

LINE VOLTAGE

HEATING LOAD

NO. 1

CIRCULATOR

L6008G

HOT)

(

HEATING LOAD

NO. 2

PILOTSTAT

LINE VOLTAGE

GAS CONTROL

OIL BURNER RELAY

LINE VOLTAGE

TERMINALS

JUMPER

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

M8968B

WHEN USING CIRCULATOR LOW LIMIT CONTROL,

REMOVE L1-L2 JUMPER.

Fig. 28. Typical oil burner installation using L4008G.

M8783C

Fig. 25. Typical wiring hookup using L6006 or

L6007 with L8148A.

OPERATION

For proper selection of settings, follow the boiler manufacturer

recommendations.

LINE VOLTAGE

CONTROL CIRCUIT

LINE VOLT

THERMOSTAT

LOAD

L4006

HOT)

(

High Limit Controller

R-B terminals provide high limit switching function (contacts

open at set point on temperature rise). (See Figures 30 and 31).

R-B terminals shut off burner if water temperature exceeds high

limit setting. Burner restarts when temperature drops to high

limit setting, less differential.

LOW VOLTAGE

THERMOSTAT

LOW VOLTAGE

CONTROL CIRCUIT

NOTE: On manual reset models, the reset button on the front

of the case must be pushed in to allow the burner to

operate after a high limit shutdown.

L4006

LOAD

(

HOT)

ELECTRIC

HEAT RELAY

POWER SUPPLY. PROVIDE DISCONNECT MEANS

AND OVERLOAD PROTECTION AS REQUIRED.

M1155A

Fig. 26. Typical systems with 120 volt

electric heat primaries.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Low Limit Controller

R-B terminals provide low limit switching function (contacts

open at set point on temperature rise). Maintains minimum

boiler temperature for domestic hot water. Turns on boiler at

temperature setting, less differential.

BREAKS R-B

MAKES R-W

ON RISE

LEFT SWITCH

DIFFERENTIAL

TEMPERATURE

RISE

Circulator Controller

BREAKS R-W

MAKES R-B

ON FALL

R-W terminals provide circulation control function (contacts

close at set point on temperature rise). Prevents circulation of

water that is below the desired heating temperature. Breaks

circulator circuit on temperature drop below setting less

differential; remakes on rise to setting.

INTERSTAGE

DIFFERENTIAL

BREAKS R-B

MAKES R-W

ON RISE

L6008G Adjustable Interstage Differential

SETPOINT

RIGHT SWITCH

DIFFERENTIAL

(

ADJUSTABLE)

When the temperature at the sensing element rises above the

set point of the controller, the switch on the right makes R-W. If

the temperature continues to rise through the preselected

interstage differential of the controller, the switch on the left

makes R-W.

BREAKS R-W

MAKES R-B

ON FALL

Conversely, on a temperature fall, the switch on the left makes

R-B, providing first step switching. If the temperature continues

to fall, the switch on the right makes R-B to provide sequencing

of equipment.

DIFFERENCE BETWEEN THE TEMPERATURES AT WHICH THE

TWO SWITCHES MAKE R-W. ADJUSTABLE FROM 3°F TO 10°F

(

1.7°C TO 5.6°C) ON STANDARD MODELS, OR FROM 3.6°F TO 12°F

2.0°C TO 6.7°C); 55°F TO 175°F (13°C TO 79°C) MODELS.

ADJUSTMENTS

TWO SPDT SWITCHES OPERATE IN SEQUENCE. EACH SWITCH

DIFFERENTIAL IS FIXED AT APPROXIMATELY 3°F (1.7°C) ON

STANDARD MODELS, OR AT 3.6°F (2.0°C); 55°F TO 175°F (13°C TO

9°C) MODELS.

M2999B

Adjusting Differential

Set the differential to correspond with the boiler manufacturer

recommendations. To adjust models with adjustable

Fig. 29. Operation of L6008G.

differential, rotate the wheel on the back of the snap switch,

(

See Fig. 32), until the desired reading is aligned with the

V notch in the frame. The wheel provides an adjustment from

° F to 30° F (3° C to 17° C). Replace the cover on the

Aquastat Controller.

BREAKS

ON RISE

LEFT SWITCH

DIFFERENTIAL

TEMPERATURE

RISE

MAKES

ON FALL

INTERSTAGE

DIFFERENTIAL

BREAKS

ON RISE

SETPOINT

(

ADJUSTABLE)

RIGHT SWITCH

DIFFERENTIAL

WHEEL

MAKES

ON FALL

NOTCH IN

FRAME

SNAP

DIFFERENCE BETWEEN THE TEMPERATURES AT WHICH

THE TWO SWITCHES BREAK ON TEMPERATURE RISE.

SWITCH

SWITCHES OPERATE IN SEQUENCE. RIGHT SWITCH

SELECT MODELS HAVE A SCREW TERMINAL INSTEAD

OF TAB TERMINAL.

FIRST-ON TEMPERATURE RISE.

M4671A

M8969

Fig. 30. Operation of L4008L.

Fig. 31. Adjusting the differential.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Adjust the control point to correspond with the boiler

manufacturer recommendations. To adjust, insert a

screwdriver in the slotted screw type head located beneath the

window in the cover. Turn the scale to the desired control point.

Table 3. Temperature Adjustments.

Difference Between Desired

Room Temperature and

Case Temperature

Reduce Dial Setting

°F °C

Adjusting L6008G Interstage Differential

°F

°C

The L6008G Controller has an adjustable interstage

—

0.5

differential. The set point adjustment knob determines the

temperature at which the right switch operates. The left switch

can be adjusted to operate from 3° F to 10° F (1.7° C to 5.6° C)

above the point of operation of the right switch. See Figure 30

for the operation of the L6008G. The interstage differential is

adjusted by turning the star wheel with a narrow screwdriver

inserted into the rectangular hole in the chassis. (See Fig. 32).

3/4

1-1/2

2-3/4

3-1/2

4-1/4

LEFT SWITCH

RIGHT

SWITCH

5-3/4

6-1/2

8-1/2

11-1/2

STAR WHEEL (INTERSTAGE

DIFFERENTIAL ADJUSTMENT)

EXAMPLE:

In the example shown in Fig. 33, the L6008A case is

located in a room with a lower temperature than the

controlled space. Adjusting the controlled space setting (dial

setting) is necessary to compensate for the temperature

difference of 35° F (20° C) between the two rooms. Table 3

indicates that the dial setting should be lowered 5° F (3° C)

to compensate for the 35° F (20° C) temperature difference.

SELECT MODELS HAVE FOUR TERMINALS.

M8972

Fig. 32. Interstage differential adjustment on an L6008G.

L6008A Location Differential Calibration

The L6008A1093 is calibrated for applications where the bulb

and controller case are located in the same control space.

Manual Reset

If the bulb and controller case are located in separate rooms,

and if the temperature in the two rooms is different, an

adjustment is required. Adjust the dial setting (control space

temperature setting) to compensate for the difference in

temperature.

If the device includes manual reset (L4006E, L4008E), be sure

to press the (red) reset button on the front of the case to make

sure that the controller is not locked out on safety. When

checking the system, adjust the limit setting low enough so the

temperature of the controlled medium reaches the high limit

setting. When the limit setting is reached, the Aquastat

Controller locks out and the burner shuts down. When the

temperature of the controlled medium drops to the high limit

setting, less the differential, push the manual reset button to

make the system operative again. Reset the control to the

proper high limit setting.

If the L6008A case is located in a room with a higher

temperature than indicated on the dial setting, raise the

dial setting the number of degrees listed in Table 3.

If the L6008A case is located in a room with a lower

temperature than indicated on the dial setting, lower the

dial setting the number of degrees listed in Table 3.

WALL

REMOTE

SENSING

BULB

L6008A

CASE

CONTROLLED

SPACE

ROOM

TEMPERATURE

o o

0 F (27 C)

o o

15 F (46 C)

M8790A

Fig. 33. L6008A calibration.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Check to make certain that the Aquastat Controller is properly

installed and adjusted. Put the system into operation and

observe the action of the controller through several cycles to

make certain it provides proper control of the system as

described in the OPERATION section. Make any additional

adjustments necessary for assuring comfort requirements.

CHECKOUT

WARNING

Explosion Hazard.

Can cause serious injury, death or property

damage.

This product is intended for use only in systems with a

pressure relief valve.

60-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

MATERIAL SAFETY DATA SHEET

Manufacturer: Honeywell Inc., 1985 Douglas Drive North,

Minneapolis, MN 55422.

Section 1. Product And Company

Identification

Date Released: October 8, 1999

Product Name: Heat Conductive Compound

NFPA Ratings:

MSDS ID: DS9021

Synonyms: MS1699

Health 0; Flammability 1; Reactivity 0; Personal Protection B

Section 2. Composition,

Information on Ingredients

Product Use: Heat conductive material used to enhance

contact and heat transfer in temperature sensor applications.

Ingredient

CAS Number

64742-65-0

Percent

PEL

TVL

2 Lithium Complex Grease (70%):

Mineral Oil

35-50

20-25

4-9

_m_g_/_m3

₅_m_g_/_m3

64742-62-7

68815-49-6

_m_g_/_m3

₅_m_g_/_m3

Lithium Hydrostearate/Sebacate

Complex

—

Zinc Alkyldithiophosphate

Aluminum Paste (30%):

Aluminum, as Al

68649-42-3

0-2

—

7429-90-5

8052-41-3

20-25

10-15

₅_m_g_/_m3

₁₀_m_g_/_m3

Aliphatic Petroleum Distillates

₉₀₀_m_g_/_m3

₅₂₅_m_g_/_m3

Stearic Acid

57-11-4

1-2

—

Aromatic Petroleum Distillates

64742-95-6

_m_g_/_m3

₅_m_g_/_m3

Additional Information: Part No. 120650 (0.5 oz tube); Part No. 107408 (4 oz can); Part No. 197007 (5 gallon container). May also

contain minute amounts of lithium and molybdenum lubricant compounds.

Section 3. Hazard Identification

Section 4. First Aid Measures

Eye Contact: Flush eyes with water for 15 minutes. Remove

any contact lenses and continue to flush. Obtain medical

attention if irritation develops and persists.

Acute Health Effects:

Skin: Excessive contact may cause skin irritation and

dermatitis.

Skin Contact: Remove excess with cloth or paper. Wash

thoroughly with mild soap and water. Obtain medical

attention if irritation develops and persists.

Eye: Direct contact with eye will cause irritation.

Inhalation: No adverse effects are expected.

Ingestion: Contact physician or local poison control center

immediately.

Ingestion: Ingestion of product may cause nausea, vomiting

and diarrhea.

Inhalation: Remove patient to fresh air and obtain medical

attention if symptoms develop.

Chronic Health Effects:

Existing skin rash or dermatitis may be aggravated by

repeated contact.

Section 5. Fire Fighting Measures

Material Flash Point: > 383° F (195° C). Will burn if exposed

to flame.

OSHA Hazard Classifications: None.

Extinguishing Media: Carbon dioxide, dry chemical or foam.

Special Fire Fighting Procedures: None.

Carcinogenicity: Not considered to be a carcinogen by

either OSHA, NTP, IARC, or ACGIH.

Explosion Hazards: None. Aluminum powder can react with

water to release flammable hydrogen gas. In this form of the

product, this reaction is not expected.

0-2104—10

L4006,7,8; L6006,7,8 AQUASTAT^®CONTROLLERS

Reactivity: Hazardous polymerization will not occur.

Incompatibilities: Strong oxidizing agents and halogens.

Section 6. Accidental Release Measures

Scrape up and dispose of as solid waste in accordance with

state and federal regulations.

Hazardous Decomposition Products: Carbon dioxide,

carbon monoxide.

Section 7. Handling and Storage

Store in dry place. Keep container closed when not in use.

Section 11. Toxicology Information.

No data available.

Section 8. Exposure Controls and Personal

Protection.

Section 12. Ecological Information

Ventilation: No special ventilation is required when working

with this product.

Chemical Fate Information: Hydrocarbon components will

biodegrade in soil; relatively persistent in water.

Respiratory Protection: None required.

Section 13. Disposal Consideration

Eye Protection: Not normally required. However, use

chemical safety goggles or faceshield if potential for eye

contact exists, especially if material is heated.

Dispose of as solid waste in accordance with local, state

and federal regulations.

Hand/Clothing Protection: Not normally required. Protective

gloves and clothing are recommended, as material is

difficult to remove from skin and clothing.

Section 14. Transportation Information

DOT Classification: Not classified as hazardous.

Other Protective Equipment: None required.

Section 15. Regulatory Information

SARA Title III Supplier Notification: Include in Section

311/312 inventory reports if amounts exceed 10,000

pounds. Aluminum compounds are subject to the reporting

requirements under Section 313 of Emergency Planning

and Community Right-To-Know Act of 1986 (40 CFR 372).

Ingredients listed in TSCA Inventory.

Section 9. Physical and Chemical Properties

Appearance/Odor: Aluminum color, semi-solid material,

pleasant odor.

Solubility in Water: Negligible.

Specific Gravity: 0.86.

Section 16. Other Information

This information is furnished without warranty, expressed or

implied, except that it is accurate to the best of our

knowledge.

Section 10. Stability and Reactivity

Stability: Stable.

60-2104—10