Honeywell RTH8580WF1007W1 Thermostat User Manual

Home

href="
User Guide  
Wi-Fi Touchscreen  
Programmable Thermostat  
RTH8500 Wi-Fi Series  
href="
In the box you will find  
Thermostat  
 Wallplate (attached to thermostat)  
 Screws and anchors  
 Coin cell battery (inside the back  
of the thermostat)  
 Quick Start Guide  
 Thermostat ID Card  
 Wire labels  
 User Guide  
6
9-2715EF—07  
ii  
href="
Welcome  
Congratulations on your purchase of a  
Honeywell Wi-Fi touchscreen programmable  
thermostat. When registered to Honeywell’s  
Total Connect Comfort Solutions, you can  
remotely monitor and control the heating and  
cooling system in your home or business—you  
can stay connected to your comfort system  
wherever you go.  
Honeywell’s Total Connect Comfort is the  
perfect solution if you travel frequently, own  
a vacation home, a business or manage an  
Investment property or if you are simply looking  
for peace of mind.  
href="
This thermostat works with common 24 volt systems such as forced air, hydronic,  
heat pump, oil, gas, and electric. It will not work with millivolt systems, such as a gas  
fireplace, or with 120/240 volt systems such as baseboard electric heat.  
This thermostat contains a Lithium battery which may contain Perchlorate material.  
Perchlorate Material—special handling may apply.  
See www.dtsc.ca.gov/hazardouswaste/perchlorate  
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains  
mercury in a sealed tube. Contact the Thermostat Recycling Corporation at www.  
thermostat-recycle.org or 1-800-238-8192 for information on how and where to  
properly and safely dispose of your old thermostat.  
NOTICE: To avoid possible compressor damage, do not run air conditioner if the  
outside temperature drops below 50°F (10°C).  
Need help?  
Visit wifithermostat.com or call 1-855-733-5465 for assistance before returning the  
thermostat to the store.  
6
9-2715EF—07  
2
Table of contents  
Setting filter reminder intervals .................43  
Cleaning the screen..................................44  
Unregistering thermostat...........................45  
Disconnecting Wi-Fi ..................................46  
Special features ........................................48  
Setting functions and options....................51  
About your new thermostat  
Home screen quick reference.....................5  
Preset energy-saving schedules.................6  
Installation  
Installing your thermostat............................8  
Connecting to your Wi-Fi network.............26  
Registering your thermostat online...........31  
Appendices  
Frequently asked questions ......................59  
Message center messages.......................62  
Troubleshooting.........................................65  
Limited warranty........................................71  
Operation  
Setting the clock........................................36  
Setting the fan...........................................37  
Selecting system mode.............................38  
Adjusting program schedules....................39  
Overriding schedules temporarily .............40  
Overriding schedules permanently ...........41  
Setting vacation hold.................................42  
6
9-2715EF—07  
3
Features of your Wi-Fi thermostat  
With your new thermostat, you can:  
 Connect to the Internet to monitor and control your heating/cooling system  
 View and change your heating/cooling system settings  
 View and set temperature and schedules  
 Receive alerts via email and get automatic upgrades  
Your new thermostat provides:  
 Smart Response Technology  
 Compressor protection  
 Heat/cool auto changeover  
6
9-2715EF—07  
4
href="
Home screen quick reference  
Once your Wi-Fi thermostat is installed, it will display the home screen. Portions of this  
display will change depending on how you are viewing it. To change settings, simply press  
the appropriate area lightly with your finger.  
Message center  
Wi-Fi status  
Inside  
Select fan mode  
Schedule is on (does not  
display when off)  
Select system mode  
Program schedules  
MORE  
Additional settings  
Override schedule  
Set clock  
Lock screen for cleaning  
Unless you change the lighting function, the screen is always lit at low intensity. When you  
touch the screen, the screen brightens.  
5
69-2715EF—07  
href="
Preset energy-saving schedules  
This thermostat is pre-set with energy-saving program settings for four time periods.  
Using the default settings can reduce your heating/cooling expenses if used as directed.  
Savings may vary depending on geographic region and usage.  
Default Heat Settings  
Default Cool Settings  
WAKE  
70 °  
78 °  
6
:00 am  
LEAVE  
62 °  
70 °  
62 °  
85 °  
78 °  
82 °  
8
:00 am  
RETURN  
6
:00 pm  
SLEEP  
0:00 pm  
1
To change the settings, see pages 39–42.  
6
9-2715EF—07  
6
href="
Setting up your thermostat  
Setting up your Wi-Fi programmable touchscreen thermostat is easy. It is preprogrammed  
and ready to go as soon as it is installed and registered.  
1
2
3
Install your thermostat.  
Connect it to your home wireless network.  
Register online for remote access.  
Before you begin, you may want to watch a brief installation video.  
®
Use the QR Code at the front of this guide, or go to  
wifithermostat.com/support  
7
69-2715EF—07  
href="
Installing your thermostat  
You might need the following tools to install this thermostat:  
 No. 2 Phillips screwdriver  
 Small pocket screwdriver  
Pencil  
•ꢀ Drill and bits (3/16” for drywall,  
/32” for plaster) (optional)  
7
 Hammer (optional)  
 Electrical tape (optional)  
 Level (optional)  
1
Switch OFF power to your  
heating/cooling system.  
or  
Important! To protect your equipment,  
switch OFF the power to your heating/  
cooling system at the breaker box or  
the system switch.  
Circuit  
breaker  
box  
Heating/cooling  
system power  
switch  
6
9-2715EF—07  
8
href="
Installing your thermostat  
2
Remove old thermostat faceplate  
and leave wires connected.  
If you have an older thermostat with a  
sealed mercury tube, turn to page 2  
for proper disposal instructions.  
2
a Take a picture of the wire  
connections for later reference.  
2
b If no wire is connected to a  
terminal labeled C or no C  
terminal exists on the old  
thermostat, view the Alternate  
Wiring videos at  
C
wifithermostat.com/videos  
Important! C wire is required and  
is the primary power source for  
your thermostat. Without a C wire,  
your thermostat will not power up.  
Terminal  
designation  
9
69-2715EF—07  
href="
Installing your thermostat  
3
Label wires.  
Do not label by wire color. Use  
the supplied sticky tags to label  
each wire as you disconnect it.  
Label wires according to the old  
thermostat terminal designations,  
not by wire color.  
Sticky tag  
Blank tags  
Note: If no tag matches a  
terminal designation, write the  
appropriate letter on a blank  
sticky tag.  
4
Remove wallplate.  
Remove the old wallplate from  
the wall after all wires have been  
labeled and disconnected.  
Terminal  
designation  
C
6
9-2715EF—07  
10  
href="
Installing your thermostat  
5
Separate Wi-Fi thermostat and its  
wallplate.  
Finger holds  
Thermostat  
On your new thermostat, grasp the  
finger holds on the top and bottom of  
the wallplate with one hand and the  
thermostat (front) with the other hand.  
Pull pieces apart.  
Wallplate (back view)  
1
1
69-2715EF—07  
href="
Installing your thermostat  
6
Mount wallplate for Wi-Fi thermostat.  
Mount your new wallplate using  
screws and anchors included with the  
thermostat.  
Wallplate  
If necessary:  
Drill 3/16-in holes for drywall.  
Drill 7/32-in holes for plaster.  
HEAT PUMP  
CONVENTIONAL  
Y2  
RC  
R
RC  
R
L
E/AUX  
W2  
K
W
Y
O/B  
Y
K
Note: You may be able to use your  
existing wall anchors. Hold the wallplate  
up to the existing anchors to check for  
alignment.  
G
G
C
C
Y
W
R
G
C
6
9-2715EF—07  
12  
href="
Installing your thermostat  
Important! The Wi-Fi thermostat requires a C wire to operate. The C, or common, wire  
brings 24 VAC power to the thermostat. Many older mechanical or battery operated  
thermostats do not require a C wire. If you don’t have a C wire, try:  
 Looking for an unused wire that is pushed into the wall. Connect that wire to C and  
check that it is connected to the 24 VAC common at your heating/cooling system.  
Check the video section at wifithermostat.com  
Note: Not all heating/cooling systems label the 24 VAC common C. Check your system  
manual or contact the manufacturer to find out which terminal is the 24 VAC common.  
View the Alternate Wiring videos at wifithermostat.com/videos  
Wiring  
For conventional heating/cooling systems (natural gas, oil or electric furnace, air  
conditioner), see page 14. See “Glossary” on page 68 for further definition.  
For a heat pump system, see page 15. See “Glossary” on page 68 for further  
definition.  
1
3
69-2715EF—07  
href="
Installing your thermostat  
Wiring (conventional system)  
Remove metal jumper  
only if you have both  
R and RC wires  
7
A Wire the Wi-Fi thermostat to your conventional system.  
a
Starting with the C Wire, match the sticky tag on the  
wire to the terminal labels.  
HEAT PUMP  
CONVENTIONAL  
You must have a C wire. See page 13.  
b
Loosen screw, insert wire on inside edge of  
terminal, then tighten screw.  
Y2  
RC  
R
RC  
R
R
L
E/AUX  
K
W
W
Y
O/B  
Y
W2  
K
c
Verify wire is firmly secured by gently pulling  
on wire.  
Y
G
G
G
C
C
C
d
e
Repeat steps a–c for all other wires.  
Push any excess wire back into the wall  
opening after all wires are installed.  
Note: The wiring for your  
application might be different  
than the wiring from above.  
f
Continue to page 20.  
Labels don’t match? See alternate  
wiring key on pages 16–17.  
6
9-2715EF—07  
14  
href="
Installing your thermostat  
Wiring (heat pump system only)  
Labels don’t match? See alternate  
wiring key on pages 18–19.  
7
B Wire Wi-Fi thermostat to your heat pump.  
a
Starting with the C Wire, match the sticky tag on the wire to the terminal labels.  
You must have a C wire. See page 13.  
b
c
Loosen screw, insert wire on inside edge of  
terminal, then tighten screw.  
Verify wire is firmly secured by gently pulling  
on wire.  
HEAT PUMP  
RC  
R
R
L
E/AUX  
K
O
AUX  
O/B  
d
e
Repeat steps a–c for all other wires.  
Push any excess wire back into the wall  
opening after all wires are installed.  
Continue to page 20.  
Y
Y
G
G
C
C
f
Note: The wiring for your  
application might be different  
than the wiring from above.  
Note: If old thermostat has separate wires on AUX and E,  
place both wires into the E/AUX terminal. If old thermostat  
has wire on AUX with a jumper to E, place wire on E/AUX  
terminal. No jumper is required.  
1
5
69-2715EF—07  
href="
Installing your thermostat  
Alternate wiring (conventional system)  
Use this if your wire labels don’t match the terminal labels.  
CONVENTIONAL  
Note: You must have  
Metal Jumper  
a C wire or equivalent.  
See page 13.  
RC  
Y2  
Y2  
RC  
R
1
2
R
W
Y
W2  
K
W2  
W
Y
3
G
C
G
C
See key to –  
1 3  
on page 17.  
6
9-2715EF—07  
16  
href="
Installing your thermostat  
Alternate wiring key (conventional system)  
Remove metal jumper connecting R and RC only if you must connect both  
R and RC.  
1
If your old thermostat had both R and RH wires, remove metal jumper.  
Connect the R wire to the RC terminal, and the RH wire to the R terminal.  
2
3
Do not use K terminal. For future use.  
1
7
69-2715EF—07  
href="
Installing your thermostat  
Alternate wiring (heat pump system only)  
Use this if your wire labels don’t match the terminal labels.  
HEAT PUMP  
Metal Jumper  
Note: You must have  
a C wire or equivalent.  
See page 13.  
RC  
R
Y2  
RC  
R
1
2
5
L
E/AUX  
K
O
6
7
O/B  
Y
3
4
AUX  
Y
G
G
C
C
3
MCR33530A  
See key to –  
1 7  
on page 19.  
6
9-2715EF—07  
18  
href="
Installing your thermostat  
Alternate wiring key (heat pump system only)  
1
2
Leave metal jumper between R and RC terminals in place.  
If your old thermostat had both V and VR wires, check wifithermostat.com for help.  
If your old thermostat had separate O and B wires, attach the B wire to the C terminal. If  
another wire is attached to the C terminal, check wifithermostat.com for help. Attach the O wire  
to the O/B terminal. Set System Function 0190 to 0 (see page 55).  
3
If your old thermostat had an O wire and not a B wire, attach the O wire to the O/B terminal.  
4
5
If your old thermostat had separate Y1, W1 and W2 wires, check wifithermostat.com for help.  
This is the system monitor. If the monitor finds a problem, you will see a red light in the upper  
right corner of the thermostat (shines through the cover).  
If old thermostat has separate wires on AUX and E, place both wires into the E/AUX terminal. If  
old thermostat has wire on AUX with a jumper to E, place wire on E/AUX terminal. No jumper is  
required.  
6
7
Do not use K terminal. For future use.  
1
9
69-2715EF—07  
href="
Installing your thermostat  
8
Install battery.  
Insert the coin cell battery  
(included), observing the  
correct polarity.  
Note: A correctly inserted  
battery will extend about halfway  
out of the battery slot on the  
thermostat, allowing for easier  
removal.  
Thermostat interior  
This battery maintains time and  
date during power outages. It  
does not power the thermostat  
(
C wire required).  
6
9-2715EF—07  
20  
href="
Installing your thermostat  
9
Attach thermostat to wallplate.  
Wallplate  
Align the thermostat to the wallplate  
and then snap into place.  
HEAT PUMP  
CONVENTIONAL  
Y2  
RC  
RC  
L
AUX  
/
E
K
Thermostat  
2
1
69-2715EF—07  
href="
Installing your thermostat  
1
0 Switch heating/cooling system ON.  
Important!  
1
0a Verify that the C wire is  
connected at the thermostat  
and at the heating/cooling  
system.  
or  
1
1
0b Make sure the heating/  
cooling system door is firmly  
secured.  
0c Switch power back ON for  
your heating/cooling system  
at the breaker box or its  
power switch.  
Circuit  
breaker  
box  
Heating/cooling  
system power  
switch  
6
9-2715EF—07  
22  
href="
Installing your thermostat  
1
1 Set date and time.  
Day  
Year  
Touch s or t buttons to change  
displayed time and date.  
Press and hold a button to quickly  
change a setting.  
Note:This thermostat will  
Month  
automatically update for daylight  
saving time (if observed in your area)  
and all date/time information is stored.  
If the thermostat is connected to  
Wi-Fi and registered to Total Connect  
Comfort, the current time is updated  
from the internet.  
Time  
2
3
69-2715EF—07  
href="
Installing your thermostat  
1
2 Determine your heating/cooling system type.  
Important! Heating/cooling system type must be set so that your  
thermostat operates properly and does not damage your system.  
12a If you have a traditional system (natural gas forced air with A/C),  
your hermostat is set up by default to control this system.  
1
2b If your system is:  
If you are not sure of your  
heating/cooling system type  
or have other questions,  
go to wifithermostat.com  
ꢀ Conventionalꢀmultistageꢀheatꢀandꢀcool  
ꢀ Anyꢀtypeꢀofꢀheatꢀpump  
ꢀ Hydronic  
ꢀ Other  
You MUST change the system type by setting system function 0170.  
See page 54 to match your thermostat to your system type.  
6
9-2715EF—07  
24  
href="
Installing your thermostat  
Congratulations! Your thermostat is operational.  
1
3 Test your thermostat.  
Inside  
1
3a Press the SYSTEM button to change to  
heating or cooling and begin operation.  
1
3b For remote access to your thermostat,  
continue to “Connecting to your Wi-Fi  
network” on page 26.  
MORE  
Heating/cooling system not turning  
on? Refer to page 67 or FAQ at  
wifithermostat.com/support  
2
5
69-2715EF—07  
href="
Connecting to your Wi-Fi network  
To complete this process, you must have a wireless device connected to your home  
wireless network. Any of these device types will work:  
•ꢀ Tablet (recommended)  
•ꢀ Laptop (recommended)  
•ꢀ Smartphone  
If you get stuck... at any point in this procedure, restart the thermostat by removing  
the thermostat from the wallplate, wait for 5 seconds, and snap it back onto the  
wallplate. Return to Step 1 in this procedure, which starts on page 27.  
View the Wi-Fi Enrollment video at wifithermostat.com/videos  
6
9-2715EF—07  
26  
href="
Connecting to your Wi-Fi network  
1
Connect to your thermostat.  
1
1
1
a Make sure the thermostat message center displays  
Wi-Fi SETUP.  
b On the wireless device (laptop, tablet, smartphone),  
view the list of available Wi-Fi networks  
Inside  
c Connect to the network called  
NewThermostat_123456 (the number will vary).  
MORE  
Note: If you are asked to specify a home, public, or  
office network, select Home Network.  
2
7
69-2715EF—07  
href="
Connecting to your Wi-Fi network  
2
Join your home network.  
2
a Open your web browser to access the  
Thermostat Wi-Fi Setup page. The browser  
should automatically direct you to the correct  
page; if it does not, go to http://192.168.1.1  
2b Find the name of your home network on this  
page and select it.  
Note: Some routers have enhanced features such as  
guest networks; use your home network  
2c Complete the instructions for joining your Wi-Fi  
network and click on the Connect button.  
(Depending on your network setup, you may see  
an instruction such as Enter Password for your home network.)  
Note: If you did not correctly connect to the thermostat, you may see  
your home router page. If so, return to Step 1.  
6
9-2715EF—07  
28  
Connecting to your Wi-Fi network  
Note: If your Wi-Fi network does not appear in the list on the Thermostat Wi-Fi Setup  
page:  
 Try performing a network rescan by pressing the Rescan button. This is helpful in  
areas with a lot of networks.  
 If you are connecting to a hidden network, then enter the network SSID in the  
textbox, select the encryption type from the drop down menu, and click on the  
Add button. This manually adds the network to the top of the list. Click on the new  
network in the list and enter the password if necessary. Click on Connect to join the  
network.  
2
9
69-2715EF—07  
href="
Connecting to your Wi-Fi network  
3
Make sure your thermostat is connected.  
The message center on your thermostat will  
now display CONNECTING… for up to 30  
seconds.  
Inside  
Look at the thermostat display. Verify that the  
message center displays one of the following:  
CONNECTION SUCCESSFUL  
MORE  
JOINED: [WI-FI NETWORK NAME]  
YOU ARE ALMOST DONE  
REGISTER AT TOTAL CONNECT  
If you see one of these messages, continue on page 31.  
Note: If you see CONNECTION FAILURE or Wi-Fi SETUP in the  
message center, confirm you correctly entered your home network  
password in step 2c. If correct, refer to the FAQ at wifithermostat.com/support  
6
9-2715EF—07  
30  
href="
Registering your thermostat online  
To view and set your Wi-Fi thermostat  
remotely, you must have a Total Connect  
Comfort account. Use the following steps.  
1
Open the Total Connect Comfort web site.  
Go to mytotalconnectcomfort.com  
View the Wi-Fi Thermostat Registration  
video at wifithermostat.com/videos  
3
1
69-2715EF—07  
href="
Registering your thermostat online  
2
Login or create an account.  
If you have an account,  
click Login  
or –  
click Create An Account  
2
2
a Follow the instructions on the screen.  
b Check your email for an activation  
message from My Total Connect Comfort.  
This may take several minutes.  
Note: If you do not receive a response, check  
your junk mailbox or use an alternate e-mail  
address.  
2
c Follow activation instructions in the  
email.  
2
d Log in.  
6
9-2715EF—07  
32  
href="
Registering your thermostat online  
3
Register your Wi-Fi thermostat.  
After you are logged in to your Total Connect Comfort account,  
register your thermostat.  
3
a Follow the instructions  
on the screen. After  
adding your thermostat  
location, you must enter  
the thermostat’s unique  
identifiers:  
Thermostat ID Card  
Use the MAC ID and CRC ID to register  
this product at mytotalconnectcomfort.com  
HONEYWELL MODEL: RTH8580WF  
MAC ID: MAC CRC:  
Carte d’identification de thermostat  
Utilisez l’identification MAC et l’identification CRC pour  
enregistrer ce produit à mytotalconnectcomfort.com  
Tarjeta de identificación del termostato  
Utilice la identificación MAC y la identificación CRC para  
inscribir este producto en mytotalconnectcomfort.com  
ꢀ MACꢀID  
ꢀ MACꢀCRC  
®
©
U.S. Registered Trademark.  
2012 Honeywell International Inc.  
6
9-2723EFS—01 M.S. 04-12  
Printed in U.S.A.  
69-2723EFS-01  
Note: These IDs are listed on the  
Thermostat ID Card included in  
the thermostat package. The IDs  
are not case sensitive.  
MAC ID  
MAC CRC  
3
3
69-2715EF—07  
href="
Registering your thermostat online  
3
b When the thermostat is  
successfully registered,  
the Total Connect Comfort  
registration screen will display a  
SUCCESS message.  
In the thermostat message  
center you will see:  
CONGRATULATIONS  
SETUP COMPLETE!  
6
9-2715EF—07  
34  
href="
Registering your thermostat online  
Your thermostat will display wireless signal  
strength.  
You can now control your thermostat from  
anywhere through your laptop, tablet, or  
smartphone.  
Total Connect Comfort free app is  
®
®
®
available for Apple iPhone , iPad  
®
®
and iPod touch devices at iTunes  
®
or at Google Play for all Android™  
devices.  
GET IT ON  
Download on  
iTunes  
3
5
69-2715EF—07  
href="
Setting the clock  
1
2
Press CLOCK to display setting arrows.  
Press s or t to adjust the time. (You can  
advance the time more quickly by holding the s  
or t buttons.)  
MORE  
3
Press DONE to save and exit (or press CANCEL to  
exit without changing the time).  
Note: This thermostat will automatically update for  
daylight saving time (if observed in your area) and  
all date/time information is stored. If the thermostat  
is connected to Wi-Fi and registered to Total  
Connect Comfort, the current time is updated from  
the internet.  
Note: To change the current week day format, see “Schedule Options” on page 53.  
6
9-2715EF—07  
36  
href="
Setting the fan  
1
2
Press FAN to select fan operation.  
Press FAN again to select ON or AUTO (toggle  
to re-select). The selected option blinks.  
Inside  
3
Press DONE to save setting. Your selection  
appears under FAN.  
ON: Fan is always on.  
AUTO: Fan runs only when the heating or  
cooling system is on.  
MORE  
3
7
69-2715EF—07  
href="
Selecting system mode  
1
2
Press SYSTEM to display options.  
Press SYSTEM again to select an option.  
You may need to press two or three times to  
make a selection—the selected option blinks.  
Inside  
3
Press DONE to save setting.  
Possible system modes:  
HEAT: Controls only the heating system.  
COOL: Controls only the cooling system.  
OFF: Heating/cooling systems are off.  
MORE  
AUTO: Selects heating or cooling  
depending on the indoor temperature.  
Note: The AUTO and EM HEAT  
system settings may not  
EM HEAT (heat pumps with aux. heat):  
Controls auxiliary/emergency heat.  
Compressor is locked out.  
appear, depending on how  
your thermostat was installed.  
6
9-2715EF—07  
38  
href="
Adjusting program schedules  
1
Press SCHED, then EDIT. Screen displays day  
buttons at top.  
MORE  
SLEEP  
2
3
Press day buttons (MONSUN) to select days.  
Press s or t to set Wake time for selected  
day(s).  
4
5
6
Press s or t to set Heat and Cool  
temperature for this time period.  
Press another period (LEAVE, RETURN, SLEEP)  
and set time and temperatures for each.  
Press DONE to save and exit (or press CANCEL  
to exit without saving changes).  
Note: You can press CANCEL PERIOD to eliminate  
any unwanted time period.  
SLEEP  
3
9
69-2715EF—07  
href="
Overriding schedules temporarily  
1
On the home screen, press s or t to  
immediately adjust the temperature.  
2
Adjust the time to when you want the hold  
to end (the default is the end of the current  
period).  
Inside  
Temporary Hold  
The new setting will be maintained until the  
time shown under Hold Until. When the timer  
expires, the schedule will resume, and the  
temperature will return to the setting for the  
current time period.  
Hold Until  
MORE  
To cancel the temporary setting at any time,  
press CANCEL (or SCHED). The program  
schedule will resume.  
6
9-2715EF—07  
40  
href="
Overriding schedules permanently  
1
Press HOLD to permanently adjust the  
temperature. This will turn off the program  
schedule.  
Inside  
2
Whatever temperature you set will be  
maintained 24 hours a day until you  
manually change it or press CANCEL  
Permanent Hold  
(
or SCHED) to cancel “Hold” and resume  
the program schedule.  
MORE  
4
1
69-2715EF—07  
href="
Setting vacation hold  
Inside  
Use this function to suspend the program schedule  
while you are away for an extended period.  
1
2
Press s or t to set the temperature.  
Hold Until  
Press s or t to set the time of day you want  
the schedule to resume on the day you return.  
MORE  
3
4
Press HOLD twice. Hold Until appears.  
Press s or t to select the number of days.  
The selected temperature will be maintained 24  
hours a day for the number of days you select.  
After the selected number of days has elapsed, the  
previously programmed schedule will resume at  
the time you set.  
DAYS  
Hold Until  
MORE  
Note: You can press CANCEL (or SCHED) to resume  
normal schedule.  
6
9-2715EF—07  
42  
href="
Setting filter reminder intervals  
Inside  
If activated during installation, the filter reminder  
alerts you with a message above the time when  
it is time to replace your filter.  
RESET  
Press RESET after changing the filter, to restart  
the timer.  
CHANGE FILTER  
MORE  
SLEEP  
To change the reminder interval:  
1
2
Press MORE, then EDIT.  
Press s or t to select the desired interval  
(
in days), then press DONE.  
DAYS  
3
4
Press RESET.  
FILTER  
Press DONE to save and exit.  
Note: System setting function 0500 governs the  
filter interval. See “Filter Change Reminder” on  
page 57.  
4
3
69-2715EF—07  
href="
Cleaning the screen  
1
Press SCREEN to lock the screen for cleaning.  
The screen will remain locked for 30 seconds  
so you can clean the screen without changing  
any settings.  
MORE  
2
After 30 seconds, press DONE to resume  
normal operation, or press SCREEN again if  
you require more time for cleaning.  
Note: Do not spray any liquid directly on the  
thermostat. Spray liquid onto a cloth, then use  
the damp cloth to clean the screen. Use water  
or household glass cleaner. Avoid abrasive  
cleansers.  
6
9-2715EF—07  
44  
href="
Unregistering thermostat  
If you remove the thermostat from your  
Total Connect Comfort website account (for  
example, you’re moving and leaving the  
thermostat behind), the message center  
will scroll UNREGISTERED FROM TOTAL  
CONNECT for 3 minutes.  
Inside  
After that, it will alternate displaying  
REGISTER AT TOTAL CONNECT, the MAC  
ID and the MAC CRC.  
MORE  
4
5
69-2715EF—07  
href="
Disconnecting Wi-Fi  
Replacing your router  
If you disconnect the thermostat from your Wi-Fi  
network:  
Inside  
1
2
Enter system setup (see page 51).  
Change setting 900 to 0 (see page 58).  
The Message Center will display Wi-Fi  
DISCONNECTED for 1 minute. After that it will display  
Wi-Fi SETUP.  
MORE  
Re-connect to a Wi-Fi network by following the steps on page 26.  
Turning Wi-Fi off  
If you do not plan to control the thermostat remotely, you can remove the Wi-Fi SETUP  
message from the screen:  
1
2
Enter system setup (see page 51).  
Change setting 890 to 0 (see page 58). Wi-Fi SETUP will be removed from the  
screen. If you want to connect to the Wi-Fi network later, change setting 890 back to 1.  
6
9-2715EF—07  
46  
href="
Software updates  
Honeywell periodically issues updates to the software for  
this thermostat. The updates occur automatically through  
your Wi-Fi connection. All your settings are saved, so  
you will not need to make any changes after the update  
occurs.  
While the update is taking place, your thermostat screen  
goes blank and the message center shows UPDATING  
and the percentage of the update that has occurred.  
When the update is complete, your home screen will  
appear as usual.  
Note: If you are not connected to Wi-Fi or registered at  
Total Connect Comfort, you will not get automatic updates.  
4
7
69-2715EF—07  
href="
Smart Response Technology  
This feature allows the thermostat to “learn”  
how long the heating/cooling system takes to  
reach programmed temperature settings, so  
the temperature is reached at the time you set.  
For example: Set the Wake time to 6:00 am,  
and the temperature to 70°. The heat will come  
on before 6:00 am, so the temperature is 70°  
by 6:00 am.  
Note: System setting function 0530 controls  
Smart Response Technology. See “Smart  
Response Technology” on page 57.  
The message “Recovery” is displayed  
when the system is activated before a  
scheduled time period.  
6
9-2715EF—07  
48  
href="
Compressor protection  
This feature forces the compressor to wait  
a few minutes before restarting, to prevent  
equipment damage.  
During the wait time, the message  
Wait” is displayed on screen.  
4
9
69-2715EF—07  
href="
Auto changeover  
This feature is used in climates where both  
air conditioning and heating are used on the  
same day.  
When the system is set to AUTO,  
the thermostat automatically  
selects heating or cooling  
depending on the indoor temperature.  
Heat and cool settings must be at least  
3
degrees apart. The thermostat will  
automatically adjust settings to maintain this  
-degree separation.  
3
Note: System setting function 0300 controls  
Auto changeover. See “Manual/Auto  
Changeover” on page 56.  
6
9-2715EF—07  
50  
href="
Setting functions and options  
You can change options for a number of system functions. Available functions depend on  
the type of system you have. The functions, designated with four-digit numbers, along with  
available options are described on pages 52–58.  
This thermostat is pre-set for a single-stage heating/cooling system.  
Setting function 0170 for a heat pump will adjust the default settings.  
1
2
3
4
5
Press SYSTEM. You’ll see several blank buttons  
on the bottom of the display.  
SYSTEM  
HEAT  
6
:30PM  
Press and hold the center blank button until  
the screen changes (approximately 5 seconds).  
DONE  
CANCEL  
Cycle through the functions, press st next to  
the four digit number on the left.  
0
120  
20  
As needed, change options for any function by  
pressing st next to the number on the right.  
DONE  
When you have made all changes, press DONE  
to save and exit.  
5
1
69-2715EF—07  
href="
System setup  
How do I set my thermostat name? (See page 51 for instructions.)  
Function  
Settings & Options  
0
112 Device Name  
52 = Thermostat  
1
2
3
4
5
6
7
8
9
Basement  
Bathroom  
Bathroom 1  
Bathroom 2  
Bathroom 3  
Bedroom  
Bedroom 1  
Bedroom 2  
Bedroom 3  
16 Exercise Room 30 Library  
44 Porch  
This name will  
identify the  
thermostat when you  
17 Family Room  
18 Fireplace  
19 Foyer  
20 Game Room  
21 Garage  
31 Living Room 45 Rec Room  
32 Lower Level 46 Sewing Room  
33 Master Bath 47 Spa  
48 Storage Room  
35 Media Room 49 Studio  
view it remotely.  
34 Master Bed  
If you register  
multiple thermostats,  
give each one a  
different name.  
22 Great Room  
23 Guest Room  
24 Gym  
25 Kid's Room  
26 Kitchen  
36 Music Room 50 Sun Room  
37 Nursery  
38 Office  
39 Office 1  
40 Office 2  
41 Pantry  
51 Theater  
52 Thermostat  
53 Upper Level  
54 Utility Room  
55 Walk In Closet  
56 Wine Cellar  
57 Workshop  
1
1
1
1
1
1
0 Bedroom 4  
1 Boat House  
2 Bonus Room  
27 Kitchen 1  
3 Computer Room 28 Kitchen 2  
42 Play Room  
29 Laundry Room 43 Pool Room  
4 Den  
5 Dining Room  
6
9-2715EF—07  
52  
href="
System setup  
How do I change time and date settings? (See page 51 for instructions.)  
Function  
Settings & Options  
0
120 Year Setting  
20 = Year 20xx  
21 = Year 21xx  
(
first two digits)  
0
130 Year Setting  
last two digits)  
0199 (i.e., 2001–2099)  
(
0
0
0
140 Month Setting  
0112 (i.e., January–December)  
0131  
150 Date Setting  
160 Schedule Options  
4
0
Program schedule is on (7-day programmable).  
Program schedule is off. Thermostat can not be programmed.  
0
165 Restore Schedule  
0
1
Continue using programmed schedule.  
Restore thermostat program to energy saving settings  
Defaults  
Note: If thermostat is connected to Wi-Fi and registered to Total Connect Comfort, the current time  
and date is updated from the internet. If you live in an area that observes daylight saving time, the  
time is also automatically updated.  
69-2715EF—07  
5
3
href="
System setup  
How do I set my heating/cooling system type? (See page 51 for instructions.)  
Function  
Settings & Options  
0
170 Select System  
1
2
4
Heat/cool: Gas, oil or electric heating with central air conditioning.  
Heat pump: Heat pump without backup or auxiliary heat.  
Heat only with fan: Gas, oil or electric heat without central air  
conditioning.  
Heat only (no fan): Gas, oil or hot water heat without central air  
conditioning.  
Type  
If you are not sure of  
your heating/cooling  
system type or have  
other questions,  
go to  
5
6
7
8
Cool only: Central air conditioning only.  
Heat pump: Heat pump with backup or auxiliary heating.  
Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 2  
cooling stages (wires on Y and Y2).  
wifithermostat.com  
9
Heat/Cool Multiple stages: 2 heat stages (wires on W and W2), 1  
cooling stage (wire on Y).  
1
0
Heat/Cool Multiple stages: 1 heat stage (wire on W), 2 cooling stages  
(
wires on Y and Y2).  
6
9-2715EF—07  
54  
href="
System setup  
How do I customize my heating/cooling system? (See page 51 for instructions.)  
Function  
Settings & Options  
Note: Depending on system settings, functions on this page might not appear.  
0
180 Heating Fan  
0
1
Gas or oil heat: Use this setting if you have a gas or oil heating system  
(system controls fan operation).  
Electric heat: Use this setting if you have an electric heating system  
Control  
(
thermostat controls fan operation).  
0
190 Heat Pump  
0
1
Cooling changeover valve: Use this setting if you connected a wire  
labeled “O” to the O/B terminal.  
Heating changeover valve: Use this setting if you connected a wire  
Changeover Valve  
(
for heat pumps  
only)  
labeled “B” to the O/B terminal.  
0
240 Heating Cycle  
5
9
3
Gas or oil furnace: Standard gas/oil furnace (less than 90% efficiency).  
Electric furnace: Electric heating systems.  
Hot water or high-efficiency furnace: Hot water system or gas furnace  
(more than 90% efficiency).  
Gas/oil steam or gravity system: Steam or gravity heat systems.  
Rate  
0
250 Heating Cycle  
Rate Stage 2  
1
5
5
69-2715EF—07  
href="
System setup  
What other functions can I change? (See page 51 for instructions.)  
Function  
Settings & Options  
0
280 Backlight  
0
1
Backlight off, then on for approximately 8 seconds after keypress.  
Backlight always on low intensity, full bright after keypress.  
0
300 Manual/Auto  
0
1
Manual changeover (Heat/Cool/Off).  
Automatic changeover (Heat/Cool/Auto/Off). Automatically turns on Heat  
or Cool based on room temperature. Note: System maintains minimum  
Changeover  
See page 50 for  
more information.  
3
°F difference between heat and cool settings.  
0
320 Temperature  
0
1
Fahrenheit  
Celsius  
Format (°F/°C)  
0
330 Automatic Daylight  
Saving Time  
0
1
Off  
On  
Adjustment  
6
9-2715EF—07  
56  
href="
System setup  
What other functions can I change? (See page 51 for instructions.)  
Function  
Settings & Options  
0
500 Filter Change  
0
Off (no reminder)  
Reminder  
1
2
3
4
5
6
7
8
Reminder after 10-day run time (about 1 calendar month)  
Reminder after 30-day run time (about 3 calendar months)  
Reminder after 60-day run time (about 6 calendar months)  
Reminder after 90-day run time (about 9 calendar months)  
Reminder after 120-day run time (about 1 calendar year)  
Reminder after 180-day run time (about 18 calendar months)  
Reminder after 270-day run time (about 2 calendar years)  
Reminder after 365-day run time (about 3 calendar years)  
The reminder  
appears after  
selected number of  
days run time not  
actual time.  
0
530 Smart Response  
1
0
On  
Off  
Technology  
See page 48 for  
more information.  
0
640 Clock Format  
12 12-hour clock (i.e., “3:30 pm”)  
24-hour clock (i.e., “15:30”)  
2
4
5
7
69-2715EF—07  
href="
System setup  
How do I change my Wi-Fi settings? (See page 51 for instructions.)  
Function  
Settings & Options  
0
710 Restore Original  
0
1
No  
Settings  
Disconnects thermostat from Wi-Fi and restores original settings (erases  
customizations).  
0
890 Wi-Fi On/Off  
1
0
Wi-Fi is on and can be connected to a Wi-Fi network.  
Wi-Fi is off. Thermostat cannot be connected to a Wi-Fi network. If you  
are not connecting the thermostat to a Wi-Fi network this will remove the  
text “Wi-Fi Setup” from the messaging center.  
0
900 Wi-Fi Connection  
1
0
Connected to Wi-Fi network. This is set automatically when the  
thermostat is connected to the Wi-Fi network.  
Set to 0 to disconnect from the Wi-Fi network.  
6
9-2715EF—07  
58  
Frequently asked questions  
Q: Will my thermostat still work if I lose my Wi-Fi connection?  
A: Yes, the thermostat will operate your heating and/or cooling system with or without Wi-Fi.  
Q: How do I find the password to my router?  
A: Contact the manufacturer of the router or check the router documentation.  
Q: Why am I not seeing my Wi-Fi setup page?  
A: You are probably connected only to your router, not to your thermostat. Try connecting to the  
thermostat again.  
Q: Why isn’t my thermostat connecting to my Wi-Fi router even though it is very close to the  
thermostat?  
A: Verify that the password entered for the Wi-Fi router is correct.  
5
9
69-2715EF—07  
Frequently asked questions  
Q: Where can I find my MAC ID and MAC CRC codes?  
A: The MAC ID and MAC CRC will show in the message center of the thermostat. The numbers are  
also included on a card packed with the thermostat or on the back of the thermostat (visible when  
removed from wallplate). Each thermostat has a unique MAC ID and MAC CRC.  
Q: My thermostat is unable to register to the Total Connect Comfort website.  
A: Verify that the thermostat is correctly enrolled on your homeWi-Fi network. The message center  
will display “CONNECTION SUCCESSFUL” or “REGISTER AT TOTAL CONNECT.” You might also  
see the Wi-Fi Signal strength icon. Verify that the Wi-Fi router has a good internet connection. On  
your computer, verify that you can open the site at mytotalconnectcomfort.com If you cannot open  
the site, switch off the internet modem for a few seconds, then power it back on.  
6
9-2715EF—07  
60  
Frequently asked questions  
Q: I registered on the Total Connect Comfort website but was unable to login using my new  
account.  
A: Check your email and ensure that you received an activation email. Follow the instructions to  
activate your account and then login to the website.  
Q: I have signed up on Total Connect Comfort website and have not received a confirmation  
email.  
A: Check for the email in your Junk or Deleted folder.  
Q: Is there a way to extend the signal strength?  
A: Most standard routers can be set up to be a repeater. You can also purchase and install a Wi-Fi  
repeater.  
For more FAQs, see wifithermostat.com  
6
1
69-2715EF—07  
href="
Message center messages  
The Message Center at the top of the screen communicates Wi-Fi connection and  
registration status. It also displays the MAC ID and MAC CRC for registering the  
thermostat at mytotalconnectcomfort.com  
Displayed before you begin Wi-Fi setup.  
Displayed while connecting to the Wi-Fi network.  
Displayed after connecting to the Wi-Fi network.  
[
Wi-Fi network name]  
Displayed when connected to the Wi-Fi network.  
Displayed when Wi-Fi connection is complete.  
Displayed when the thermostat fails to establish a connection  
to the Wi-Fi network.  
Displayed when the thermostat is connected to the Wi-Fi  
network but not registered at mytotalconnectcomfort.com  
[
[
Found on your ID card]  
Found on your ID card]  
Displays the thermostat’s MAC ID and MAC CRC for  
registering at mytotalconnectcomfort.com  
6
9-2715EF—07  
62  
href="
Message center messages  
Displayed when the thermostat is registered at  
mytotalconnectcomfort.com  
Displayed when the thermostat is removed from your Total  
Connect Comfort account.  
Wi-Fi signal strength. Displayed when the thermostat  
is connected to the Wi-Fi network and registered at  
mytotalconnectcomfort.com  
Displayed if there is no Wi-Fi signal.  
ꢀ CheckꢀanotherꢀdeviceꢀtoꢀbeꢀsureꢀWi-Fiꢀisꢀworkingꢀinꢀyourꢀ  
home; if not, call your Internet Service Provider.  
ꢀ Moveꢀtheꢀrouter.  
ꢀ Restartꢀtheꢀthermostat:ꢀremoveꢀitꢀfromꢀtheꢀwallplate,ꢀwaitꢀ  
5
seconds, and snap it back onto the wallplate. Return to  
Step 1 of Connecting to your Wi-Fi network.  
6
3
69-2715EF—07  
href="
Message center messages  
Displayed if the home Wi-Fi password is entered incorrectly.  
ꢀ Re-enterꢀpasswordꢀforꢀyourꢀhomeꢀWi-Fiꢀnetwork.  
ꢀ Repeatꢀsetupꢀprocessꢀandꢀconfirmꢀyourꢀpasswordꢀforꢀyourꢀ  
home Wi-Fi network.  
Displayed if no IP Address is supplied by the router.  
ꢀ Waitꢀforꢀ30ꢀminutes,ꢀconnectionꢀcanꢀtakeꢀseveralꢀminutes.ꢀ  
If still no connection, remove thermostat from wallplate,  
wait 5 seconds, and snap it back onto the wallplate.  
ꢀ VerifyꢀyourꢀrouterꢀisꢀcorrectlyꢀsetupꢀtoꢀautomaticallyꢀgiveꢀIPꢀ  
addresses.  
Displayed if there is no Wi-Fi signal.  
ꢀ MakeꢀsureꢀtheꢀInternetꢀcableꢀisꢀpluggedꢀin.  
ꢀ Rebootꢀtheꢀrouter.  
6
9-2715EF—07  
64  
href="
Troubleshooting  
If you have difficulty with your thermostat, please try the following suggestions.  
Most problems can be corrected quickly and easily.  
Display is  
blank  
•ꢀ Checkꢀcircuitꢀbreakerꢀandꢀresetꢀifꢀnecessary.  
•ꢀ Makeꢀsureꢀpowerꢀswitchꢀatꢀheatingꢀandꢀcoolingꢀsystemꢀisꢀon.  
ꢀ Makeꢀsureꢀfurnaceꢀdoorꢀisꢀclosedꢀsecurely.  
ꢀ MakeꢀsureꢀCꢀwireꢀisꢀconnectedꢀ(seeꢀpageꢀ13).  
Cannot change •ꢀ CheckꢀFunction 0170: System Type to make sure it is set to match your  
system setting  
to Cool  
heating and cooling equipment (see page 54).  
Fan does  
•ꢀ CheckꢀFunction 0180: Heating Fan Control to make sure it is set to match  
your heating equipment (see page 55).  
not turn on  
when heat is  
required  
Wait” appears •ꢀ Compressorꢀprotectionꢀfeatureꢀisꢀengaged.ꢀWaitꢀ5ꢀminutesꢀforꢀtheꢀsystemꢀtoꢀ  
restart safely, without damage to the compressor.  
on the screen  
6
5
69-2715EF—07  
href="
Troubleshooting  
Heat pump  
•ꢀ CheckꢀFunction 0190: Heat Pump Changeover Valve to make sure it is  
properly configured for your system (see page 55).  
issues cool air  
in heat mode,  
or warm air in  
cool mode  
Button on  
lower right of  
screen is blank  
•ꢀ Thisꢀbuttonꢀwillꢀremainꢀblankꢀunlessꢀtheꢀfurnaceꢀfilterꢀchangeꢀreminderꢀisꢀ  
activated (see page 43).  
Red light is on  
•ꢀ IfꢀthermostatꢀisꢀinꢀEmergencyꢀHeatꢀmodeꢀtheꢀredꢀlightꢀisꢀnormal.ꢀItꢀshowsꢀ  
that the thermostat is in emergency heat mode.  
ꢀ IfꢀthermostatꢀisꢀnotꢀinꢀEmergencyꢀHeatꢀmode,ꢀcontactꢀaꢀqualifiedꢀserviceꢀ  
contractor for repair.  
6
9-2715EF—07  
66  
href="
Troubleshooting  
Heating or  
cooling system  
does not  
•ꢀ PressꢀSYSTEM to set system to Heat. Make sure the temperature is set  
higher than the Inside temperature.  
•ꢀ PressꢀSYSTEM to set system to Cool. Make sure the temperature is set lower  
respond  
than the Inside temperature.  
ꢀ Checkꢀcircuitꢀbreakerꢀandꢀresetꢀifꢀnecessary.  
ꢀ Makeꢀsureꢀpowerꢀswitchꢀatꢀheatingꢀ&ꢀcoolingꢀsystemꢀisꢀon.  
ꢀ Makeꢀsureꢀfurnaceꢀdoorꢀisꢀclosedꢀsecurely.  
ꢀ Ifꢀ“Wait”ꢀisꢀdisplayed,ꢀtheꢀcompressorꢀprotectionꢀtimerꢀisꢀon.ꢀWaitꢀ5ꢀminutesꢀ  
for the system to restart safely, without damaging the compressor (see page  
4
8).  
Heating system •ꢀ CheckꢀFunction 0170: System Type to make sure it is set to match your  
is running in  
cool mode  
heating and cooling equipment (see page 54).  
6
7
69-2715EF—07  
Glossary  
C wire  
The “C” or common wire brings 24 VAC power to the thermostat from the heating/cooling system.  
Some older mechanical or battery operated thermostats may not have this wire connection. It is  
necessary for establishing a Wi-Fi connection to your home network.  
Heat Pump heating/cooling system  
Heat pumps are used to heat and cool a home. If your old thermostat has a setting for auxiliary or  
emergency heat, you likely have a heat pump.  
Conventional heating/cooling system  
Non–heat pump type systems; these include air handlers, furnaces or boilers that run on natural gas,  
oil or electricity. They may or may not include an air conditioner.  
Jumper  
A small piece of wire that connects two terminals together.  
MAC ID, MAC CRC  
Alphanumeric codes that uniquely identify your thermostat.  
®
QR Code  
Quick response code. A two-dimensional,machine-readable image. Your wireless device can read  
the black and white pattern in the square and link its browser directly to a web site. QR Code is a  
registered trademark of DENSO WAVE INCORPORATED.  
6
9-2715EF—07  
68  
Regulatory information  
FCC Compliance Statement (Part 15.19) (USA only) instructions, may cause harmful interference to radio  
This device complies with Part 15 of the FCC Rules.  
Operation is subject to the following two conditions:  
communications. However, there is no guarantee that  
interference will not occur in a particular installation. If  
this equipment does cause harmful interference to radio  
or television reception, which can be determined by  
turning the equipment off and on, the user is encouraged  
to try to correct the interference by one of the following  
measures:  
1
2
This device may not cause harmful interference, and  
This device must accept any interference received,  
including interference that may cause undesired  
operation.  
FCC Warning (Part 15.21) (USA only)  
ꢀ Reorientꢀorꢀrelocateꢀtheꢀreceivingꢀantenna.  
ꢀ Increaseꢀtheꢀseparationꢀbetweenꢀtheꢀequipmentꢀandꢀ  
receiver.  
Changes or modifications not expressly approved by the  
party responsible for compliance could void the user’s  
authority to operate the equipment.  
ꢀ Connectꢀtheꢀequipmentꢀintoꢀanꢀoutletꢀonꢀaꢀcircuitꢀ  
different from that to which the receiver is connected.  
FCC Interference Statement (Part 15.105 (b))  
(
USA only)  
•ꢀ Consultꢀtheꢀdealerꢀorꢀanꢀexperiencedꢀradio/TVꢀ  
This equipment has been tested and found to comply  
with the limits for a Class B digital device, pursuant to  
Part 15 of the FCC Rules. These limits are designed  
to provide reasonable protection against harmful  
interference in a residential installation. This equipment  
generates uses and can radiate radio frequency energy  
and, if not installed and used in accordance with the  
technician for help.  
6
9
69-2715EF—07  
Regulatory information  
Thermostats  
Section 7.1.3 of RSS-GEN  
To comply with FCC and Industry Canada RF exposure Operation is subject to the following two conditions:  
limits for general population/ uncontrolled exposure, the 1 this device may not cause interference, and  
antenna(s) used for these transmitters must be installed 2 this device must accept any interference, including  
to provide a separation distance of at least 20 cm from  
all persons and must not be co-located or operating in  
conjunction with any other antenna or transmitter.  
interference that may cause undesired operation of the  
device.  
Section 7.1.2 of RSS-GEN  
Under Industry Canada regulations, this radio transmitter  
may only operate using an antenna of type and  
maximum (or lesser) gain approved for the transmitter by  
Industry Canada. To reduce potential radio interference  
to other users, the antenna type and its gain should  
be so chosen that the equivalent isotropically radiated  
power (e.i.r.p.) is not more than that necessary for  
successful communication.  
6
9-2715EF—07  
70  
1-year limited warranty  
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and  
service, for a period of one (1) year from the date of purchase by the consumer. If at any time during the warranty period the product is  
determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).  
If the product is defective,  
(
i) return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or  
(
ii) call Honeywell Customer Care at 1-855-733-5465. Customer Care will make the determination whether the product should be  
returned to the following address: Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or  
whether a replacement product can be sent to you.  
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or  
malfunction was caused by damage which occurred while the product was in the possession of a consumer.  
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT  
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES  
RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER  
FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental or consequential damages, so this  
limitation may not apply to you.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY  
IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,  
IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an  
implied warranty lasts, so the above limitation may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.  
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN  
5
5422 or call 1-855-733-5465.  
7
1
69-2715EF—07  
href="
Automation and Control Systems  
Honeywell International Inc.  
69-2715EF-07  
1
985 Douglas Drive North  
Golden Valley, MN 55422  
Honeywell Ltd  
7
05 Montrichard Avenue  
Saint-Jean-sur-Richelieu, Québec  
J2X 5K8  
wifithermostat.com  
®
U.S. Registered Trademark.  
Apple, iPhone, iPad, iPod touch and iTunes are trademarks of Apple Inc.  
All other trademarks are the property of their respective owners.  
©
6
2013 Honeywell International Inc.  
9-2715EF—07 M.S. Rev. 11-13  
Printed in U.S.A.  
href="
Guide de  
l’utilisateur  
Thermostat programmable  
à écran tactile Wi-Fi  
Série RTH8500WF Wi-Fi  
href="
Vous trouverez dans la boîte  
Thermostat  
 Plaque murale (fixée au  
thermostat)  
 Vis et ancres  
 Pile bouton (à l’intérieur de  
l’arrière du thermostat)  
 Guide de démarrage rapide  
 Carte d’identification de  
thermostat  
 Étiquettes de fils  
 Guide de l’utilisateur  
6
9-2715EF—07  
ii  
href="
Bienvenue  
Nous vous félicitons de l’achat d’un thermostat  
programmable à écran tactile Wi-Fi Honeywell.  
Après vous être enregistré auprès du service  
Total Connect Comfort de Honeywell, vous  
pouvez surveiller et contrôler à distance le  
système de chauffage et de refroidissement de  
votre domicile ou de votre entreprise — vous  
pouvez rester connecté à votre service confort  
où que vous soyez.  
Le Total Connect Comfort de Honeywell est la  
solution parfaite si vous voyagez fréquemment,  
possédez une maison de vacances ou  
une entreprise ou gérez un immeuble de  
placement, ou si tout simplement vous  
recherchez la tranquillité d’esprit.  
href="
Ce thermostat fonctionne sur les systèmes de 24 V commun tels que les systèmes  
à air pulsé, eau chaude, thermopompe, mazout, gaz et électriques. Il ne fonctionne  
pas avec les systèmes à mV, tels que les cheminées à gaz, ou avec les systèmes  
de 120/240 V tels que les chauffages de plinthe.  
Ce thermostat contient une pile au lithium pouvant contenir du perchlorate.  
Perchlorate — peut exiger une manipulation particulière.  
Consultez le site www.dtsc.ca.gov/hazardouswaste/perchlorate  
AVIS RELATIF AU MERCURE : Ne jetez pas l’ancien thermostat dans la poubelle  
s’il contient du mercure dans un tube scellé. Contactez la Thermostat Recycling  
Corporation à l’adresse www.thermostat-recycle.org ou appelez au 1-800-238-8192  
pour savoir comment et où mettre au rebut votre thermostat usagé.  
AVIS : Pour éviter d’endommager le compresseur, ne faites pas fonctionner le  
climatiseur si la température extérieure est inférieure à 10 °C (50 °F).  
Besoin d’aide?  
Consultez le site wifithermostat.com ou appelez au 1-855-733-5465 pour obtenir de l’aide  
avant de renvoyer le thermostat au magasin.  
6
9-2715EF—07  
2
Table des matières  
À propos du nouveau thermostat  
Référence rapide de l’écran d’accueil.........5  
Programmes d’économie  
Dérogation permanente  
de la programmation...............................41  
Réglage du maintien  
pendant les vacances.............................42  
Réglage des intervalles  
d’énergie préconfigurés ............................6  
Installation  
de rappel de filtre....................................43  
Nettoyage de l’écran .................................44  
Annulation de l’enregistrement  
du thermostat..........................................45  
Déconnexion Wi-Fi....................................46  
Caractéristiques spéciales........................48  
Fonctions et options de configuration.......51  
Installation de votre thermostat...................8  
Connexion à votre réseau Wi-Fi................26  
Enregistrement de votre  
thermostat en ligne ................................31  
Fonctionnement  
Réglage de l’horloge.................................36  
Réglage du ventilateur .............................37  
Sélection du mode de  
Annexes  
Questions fréquemment posées...............59  
Message center messages.......................62  
Dépannage................................................65  
Garantie limitée.........................................71  
fonctionnement du système .....................38  
Réglage des programmes.........................39  
Dérogation temporaire  
de la programmation...............................40  
6
9-2715EF—07  
3
Caractéristiques de votre thermostat Wi-Fi  
Avec votre nouveau thermostat, vous pouvez :  
 Vous connecter à Internet pour surveiller et contrôler votre système de  
chauffage/refroidissement  
 Consulter et modifier vos réglages du système de chauffage/refroidissement  
 Consulter et régler la température et les programmes  
 Recevoir des alertes par courrier électronique et obtenir des mises à jour  
automatiques  
Votre nouveau thermostat procure :  
 La technologie Smart Response  
 Une protection du compresseur  
 Une commutation automatique chaud/froid  
6
9-2715EF—07  
4
href="
Référence rapide de l’écran d’accueil  
Une fois votre thermostat Wi-Fi installé, il affichera l’écran d’accueil. Des parties de cet  
écran seront modifiées en fonction de la manière dont vous le consultez. Pour modifier  
des réglages, appuyez simplement légèrement sur la zone appropriée avec le doigt.  
Fenêtre de messages  
Statut Wi-Fi  
Inside  
Sélection du mode du  
ventilateur  
Programme activé (ne  
s’affiche pas lorsque le  
programme n’est pas activé)  
Sélection du mode de  
fonctionnement du système  
Horaires de programmation  
MORE  
Réglages additionnels  
Dérogation de  
programmation  
Réglage de l’horloge  
Verrouillage de l’écran pour  
le nettoyage  
Sauf en cas de modification de la fonction d’éclairage, l’écran est toujours allumé à faible  
intensité. Lorsque vous touchez l’écran, son intensité augmente.  
5
69-2715EF—07  
href="
Programmes d’économie d’énergie préconfigurés  
Ce thermostat contient des programmes d’économie d’énergie préconfigurés pour quatre  
périodes. L’utilisation des réglages par défaut peut vous permettre de réduire vos dépenses  
de chauffage/refroidissement si vous suivez les instructions indiquées. Les économies  
peuvent varier en fonction de la région géographique et de l’usage.  
Réglages de chauffage  
par défaut  
Réglages de  
refroidissement par défaut  
WAKE (Réveil)  
70 °  
62 °  
70 °  
62 °  
78 °  
85 °  
78 °  
82 °  
6
h
LEAVE (Départ)  
8
h
RETURN (Retour)  
8h  
1
SLEEP (Coucher)  
2h  
2
Pour modifier les réglages, voir pages 39–42.  
6
9-2715EF—07  
6
href="
Configuration de votre thermostat  
La configuration de votre thermostat programmable à écran tactile Wi-Fi est aisée. Il est  
préprogrammé et prêt à fonctionner dès qu’il est installé et enregistré.  
1
2
3
Installez votre thermostat.  
Connectez-le au réseau sans fil de votre domicile.  
Enregistrez-vous en ligne pour bénéficier de l’accès à distance.  
Avant de commencer, vous désirerez peut-être visionner une courte  
vidéo d’installation. Utilisez le QR Code® figurant sur la couverture de ce  
guide ou consultez le site wifithermostat.com/support  
7
69-2715EF—07  
href="
Installation de votre thermostat  
Vous aurez besoin des outils suivants pour l’installation de ce thermostat :  
 un tournevis Phillips n° 2  
 un petit tournevis de poche  
 un crayon  
•ꢀ un marteau (optionnel)  
•ꢀ un ruban électrique (optionnel)  
 un niveau (optionnel)  
 une perceuse et des mèches (3/16 po  
pour une cloison sèche, 7/32 po pour  
du plâtre) (optionnel)  
ou  
1
Coupez l’alimentation sur votre système  
de chauffage/refroidissement.  
Important! Pour protéger votre  
équipement, coupez l’alimentation  
de votre système de chauffage/  
refroidissement au niveau du disjoncteur  
ou du commutateur du système.  
Interrupteur  
Disjoncteur  
d’alimentation du  
système de chauffage/  
refroidissement  
6
9-2715EF—07  
8
href="
Installation de votre thermostat  
2
Retirez la plaque de l’ancien  
thermostat et laissez les fils  
connectés.  
Si vous possédez un thermostat plus  
ancien à tube de mercure scellé, allez à  
la page 2 pour les instructions de mise au  
rebut correctes.  
2
a Prenez une photo des connexions  
de câblage pour vous y référer  
plus tard.  
2
b Si aucun fil n’est connecté à la borne  
C ou si aucune borne C n’est présente  
sur l’ancien thermostat, visionnez les  
vidéos expliquant les autres câblages  
à wifithermostat.com/videos  
C
Important! Le fil C est requis et  
Désignation de la  
borne  
représente la source d’alimentation  
principale du thermostat. Sans fil C, votre  
thermostat ne se mettra pas en marche.  
9
69-2715EF—07  
href="
Installation de votre thermostat  
3
Étiquetez les fils.  
N’appliquez pas les étiquettes en  
fonction des couleurs des fils. Utilisez  
les étiquettes autocollantes fournies  
pour étiqueter chaque fil lorsque vous  
le déconnectez. Étiquetez les fils  
conformément aux désignations de  
bornes de l’ancien thermostat et non  
pas en fonction des couleurs des fils.  
Étiquette  
autocollante  
Étiquettes  
vierges  
Remarque : Si aucune étiquette ne  
correspond à une borne, notez la lettre  
appropriée sur une étiquette collante  
vierge.  
4
Retirez la plaque murale.  
Retirez l’ancienne plaque murale du  
mur après avoir étiqueté et déconnecté  
tous les fils.  
10  
Désignation  
de la borne  
C
6
9-2715EF—07  
href="
Installation de votre thermostat  
5
Séparez le thermostat Wi-Fi de sa  
plaque murale.  
Alvéoles  
Thermostat  
Sur votre nouveau thermostat,  
saisissez les alvéoles du haut et du  
bas de la plaque murale d’une main et  
tenez le thermostat (avant) dans l’autre  
main. Séparez les deux pièces.  
Plaque murale  
vue arrière)  
(
1
1
69-2715EF—07  
href="
Installation de votre thermostat  
6
Montez la plaque murale du  
thermostat Wi-Fi.  
Montez votre nouvelle plaque murale à  
l’aide des vis et ancres fournies avec le  
thermostat.  
Plaque murale  
Au besoin :  
HEAT PUMP  
CONVENTIONAL  
Percez des trous de 3/16 po (4,8 mm)  
pour les cloisons sèches.  
Y2  
RC  
R
RC  
R
L
E/AUX  
W2  
K
W
Y
O/B  
Y
K
G
G
Percez des trous de 7/32 po (5,6 mm)  
pour le plâtre.  
C
C
Remarque : Vous pourrez peut-être  
utiliser les ancres murales déjà installées.  
Tenez la plaque murale sur les ancres  
déjà installées pour vérifier l’alignement.  
Y
W
R
G
C
6
9-2715EF—07  
12  
href="
Installation de votre thermostat  
Important! le fonctionnement du thermostat Wi-Fi requiert l’utilisation d’un fil neutre (C).  
Le fil C, ou neutre, amène l’alimentation 24 V ca au thermostat. De nombreux thermostats  
mécaniques ou à piles plus anciens n’ont pas besoin d’un fil C. Si vous ne disposez pas  
d’un fil C, essayez :  
 de rechercher un fil inutilisé enfoncé dans le mur. Connectez ce fil au fil C et vérifiez  
s’il est connecté au fil C 24 V ca de votre système de chauffage/refroidissement.  
Consultez la section vidéo sur wifithermostat.com  
Remarque : Tous les systèmes de chauffage/refroidissement ne portent pas l’étiquette 24  
V c.a. commune « C ». Reportez-vous au manuel sur le système ou communiquez avec  
le fabricant afin d’identifier la borne 24 V c.a. commune.  
Visionnez les vidéos expliquant les autres câblages à wifithermostat.com/videos  
Câblage  
Pour les systèmes de chauffage/refroidissement conventionnels (gaz naturel, appareil  
de chauffage à mazout ou électrique, climatiseur), voir page 14. Voir « Glossaire » à la  
page 68 pour des définitions plus complètes.  
Pour un système à thermopompe, voir page 15. Voir « Glossaire » à la page 68  
pour des définitions plus complètes.  
69-2715EF—07  
1
3
href="
Installation de votre thermostat  
Câblage (système conventionnel)  
Retirez le cavalier  
métallique si les fils R  
et RC sont tous deux  
7
A Branchez le thermostat Wi-Fi sur votre système  
conventionnel.  
a
En commençant par le fil C, faites correspondre l’étiquette présents.  
autocollante sur le fil à l’étiquette de la borne.  
Vous devez disposer d’un fil neutre (C).  
Voir page 13.  
HEAT PUMP  
CONVENTIONAL  
b
Desserrez la vis, insérez le fil dans le bord  
intérieur de la borne et serrez la vis.  
Vérifiez que le fil est bien attaché en tirant  
délicatement dessus.  
RC  
R
RC  
R
Y2  
R
L
E/AUX  
K
W
W
Y
O/B  
Y
W2  
K
c
Y
G
G
G
d
e
Répétez les étapes a–c pour tous les autres fils.  
Poussez tout excédent de fil dans l’ouverture  
mural une fois tous les fils installés.  
Poursuivez à la page 20.  
Les étiquettes ne correspondent pas? Reportez-  
vous au code de câblage alternatif des pages 16–17.  
C
C
C
Remarque : Le câblage de  
votre application spécifique  
peut être différent du  
f
câblage illustré ci-avant.  
6
9-2715EF—07  
14  
href="
Installation de votre thermostat  
Câblage (système à thermopompe uniquement)  
Les étiquettes ne  
correspondent  
pas? Reportez-vous  
au code de câblage  
alternatif des pages  
7
B Branchez le thermostat Wi-Fi à votre thermopompe.  
a En commençant par le fil C, faites correspondre l’étiquette  
autocollante sur le fil à l’étiquette de la borne.  
Vous devez disposer d’un fil neutre (C). Voir page 13.  
18–19.  
b
c
Desserrez la vis, insérez le fil dans le bord intérieur  
de la borne et serrez la vis.  
Vérifiez que le fil est bien attaché en tirant  
délicatement dessus.  
HEAT PUMP  
RC  
R
R
d
e
Répétez les étapes a–c pour tous les autres fils.  
Poussez tout excédent de fil dans l’ouverture mural  
une fois tous les fils installés.  
L
E/AUX  
K
O
AUX  
O/B  
Y
Y
G
G
f
Poursuivez à la page 20.  
C
C
Remarque : Si l’ancien thermostat est doté de fils  
distincts aux bornes AUX et E, reliez les deux fils à  
la borne E/AUX. Si l’ancien thermostat est doté d’un  
fil à la borne AUX et d’un cavalier à la borne E, reliez  
le fil à la borne E/AUX. Aucun cavalier n’est requis.  
Remarque : Le câblage de  
votre application spécifique  
peut être différent du  
câblage illustré ci-avant.  
1
5
69-2715EF—07  
href="
Installation de votre thermostat  
Câblage alternatif (système conventionnel)  
Utilisez ceci si vos étiquettes de fils ne correspondent pas aux références de bornes.  
CONVENTIONNEL  
Cavalier  
Remarque : vous devez  
métallique  
disposer d’un fil C  
RC  
R
Y2  
Y2  
RC  
R
1
2
(
neutre) ou équivalent.  
ou  
ou  
ou  
ou  
Voir page 13.  
ou ou  
W
ou  
W2  
K
W2  
W
Y
Y
ou  
3
G
G
ou  
ou  
C
C
ou ou  
MFCR33528  
Reportez-vous aux points  
1
à de la page 17.  
3
6
9-2715EF—07  
16  
href="
Installation de votre thermostat  
Câblage alternatif (système conventionnel)  
Retirez le cavalier métallique reliant R et RC uniquement si vous devez connecter à la  
fois R et RC.  
1
Si votre ancien thermostat est pourvu de deux fils R et RH, retirez le cavalier métallique.  
Connectez le fil R à la borne RC et le fil RH à la borne R.  
2
3
N’utilisez pas la borne K. Pour une utilisation ultérieure.  
1
7
69-2715EF—07  
href="
Installation de votre thermostat  
Câblage alternatif (système à thermopompe uniquement)  
Utilisez ceci si vos étiquettes de fils ne correspondent pas aux références de bornes.  
THERMOPOMPE  
Cavalier  
métallique  
Remarque : vous devez  
disposer d’un fil C (neutre)  
ou équivalent.  
RC  
ou  
RC  
R
1
2
R
Voir page 13.  
5
L
E/AUX  
K
ou  
ou ou  
O
ou ou  
O/B  
Y
6
7
ou ou  
3
4
AUX  
ou ou  
Y
ou  
ou  
ou  
ou  
G
G
C
ou ou  
C
3
MFCR33530A  
Reportez-vous aux points  
de la page 19.  
1
à
7
6
9-2715EF—07  
18  
href="
Installation de votre thermostat  
Code de câblage alternatif (système à thermopompe uniquement)  
1
2
Laissez le cavalier métallique reliant les bornes R et RC en place.  
Si votre ancien thermostat est pourvu de deux fils V et VR, consultez le site wifithermostat.com  
pour obtenir de l’aide.  
Si votre ancien thermostat est pourvu de fils O et B séparés, fixez le fil B à la borne C. Si un  
autre fil est relié à la borne C, consultez le site wifithermostat.com pour obtenir de l’aide. Reliez  
le fil O à la borne O/B. Réglez la fonction système 0190 à 0 (voir page 55).  
3
Si votre ancien thermostat est pourvu d’un fil O et pas d’un fil B, fixez le fil O à la borne O/B.  
Si votre ancien thermostat est pourvu de fils Y1, W1 et W2 consultez le site wifithermostat.com  
pour obtenir de l’aide.  
4
5
6
Il s’agit du moniteur du système. Si le moniteur découvre un problème, vous verrez un témoin  
rouge allumé dans le coin supérieur droit du thermostat (visible à travers le couvercle).  
Si l’ancien thermostat est doté de fils distincts aux bornes AUX et E, reliez les deux fils à la  
borne E/AUX. Si l’ancien thermostat est doté d’un fil à la borne AUX et d’un cavalier à la borne  
E, reliez le fil à la borne E/AUX. Aucun cavalier n’est requis.  
7
N’utilisez pas la borne K. Pour une utilisation ultérieure.  
1
9
69-2715EF—07  
href="
Installation de votre thermostat  
8
Installez la pile.  
Insérez la pile bouton  
(incluse), en respectant la  
polarité correcte.  
Remarque : Une pile bien  
insérée dépasse de moitié de  
la fente de la batterie sur le  
thermostat, permettant un retrait  
facile.  
Intérieur du thermostat  
Cette pile permet de conserver  
l’heure et la date durant les  
coupures d’électricité. Elle  
n’alimente pas le thermostat (fil  
C requis).  
6
9-2715EF—07  
20  
href="
Installation de votre thermostat  
9
Fixez le thermostat à la plaque  
murale.  
Plaque murale  
Alignez le thermostat sur la plaque  
murale puis emboîtez-le.  
HEAT PUMP  
CONVENTIONAL  
Y2  
RC  
RC  
L
AUX  
/
E
K
Thermostat  
2
1
69-2715EF—07  
href="
Installation de votre thermostat  
1
0 Mettez le système de chauffage/  
refroidissement en marche.  
Important!  
1
0a Vérifiez que le fil C est branché  
sur le thermostat et le système  
de chauffage/refroidissement.  
ou  
1
0b Assurez-vous que la porte  
du système de chauffage/  
refroidissement est bien  
fermée.  
Interrupteur  
1
0c Rétablissez l’alimentation  
dusystème de chauffage/  
refroidissement au niveau du  
disjoncteur ou de l’interrupteur  
d’alimentation.  
Disjoncteur  
d’alimentation du  
système de chauffage/  
refroidissement  
6
9-2715EF—07  
22  
href="
Installation de votre thermostat  
1
1 Réglez la date et l’heure.  
Jour  
Mois  
Année  
Touchez les boutons s ou t pour  
modifier l’heure et la date affichées.  
Appuyez sur un bouton et  
maintenez-le pour modifier  
rapidement un réglage.  
Remarque : Ce thermostat se mettra  
à jour automatiquement à l’heure  
d’été/d’hiver (si respecté dans votre  
zone) et l’information de la date/heure  
est enregistrée. Si le thermostat est  
connecté au Wi-Fi et est enregistré  
au Total Connect Comfort, l’heure  
courante est mise à jour à partir de  
l’Internet.  
Heure  
2
3
69-2715EF—07  
href="
Installation de votre thermostat  
1
2 Déterminez le type de votre système de chauffage/refroidissement.  
Important! Le type de système de chauffage/refroidissement doit être réglé de  
sorte que le thermostat fonctionne correctement et n’endommage pas le système.  
12a Si vous avez un système traditionnel (gaz naturel air pulsé avec climatisation),  
votre thermostat est réglé par défaut pour réguler ce système.  
1
2b Si votre système est de type :  
Si vous n’êtes pas certain  
de votre type de système de  
chauffage/refroidissement  
ou avez d’autres  
questions, consultez le site  
wifithermostat.com  
•ꢀ Équipementꢀmulti-étages  
•ꢀ Toutꢀtypeꢀdeꢀthermopompe  
•ꢀ Systèmeꢀàꢀeauꢀchaude  
•ꢀ Autre  
Vous DEVEZ changer le type de système en réglant la fonction du système sur  
170. Voir la page 54 pour faire correspondre votre thermostat à votre type de  
système.  
0
6
9-2715EF—07  
24  
href="
Installation de votre thermostat  
Félicitations! Votre thermostat est maintenant  
prêt à fonctionner.  
Inside  
1
3 Testez votre thermostat.  
1
3a Appuyez sur le bouton SYSTEM  
pour passer au chauffage ou au  
refroidissement et mettre l’appareil  
en marche.  
MORE  
1
3b Pour accéder à distance à votre  
thermostat, passez à « Connexion  
à votre réseau Wi-Fi » à la  
Le système de chauffage/  
refroidissement ne s’allume pas?  
Consultez le page 67 ou la  
Foire aux questions à  
page“Connexion à votre réseau  
Wi-Fi” on page 26.  
wifithermostat.com/support  
2
5
69-2715EF—07  
href="
Connexion à votre réseau Wi-Fi  
Pour exécuter cette étape, vous devez avoir un appareil sans fil connecté à votre réseau  
sans fil. Tous ces types d’appareils sont valables :  
 Tablette (recommandé)  
 Ordinateur portatif (recommandé)  
 Téléphone intelligent  
Si vous êtes bloqué... à tout moment dans cette procédure, redémarrez le  
thermostat en le retirant de la plaque murale, attendez 5 secondes, et emboîtez-le à  
nouveau sur la plaque murale. Revenez à l’étape 1 de cette procédure, qui débute à  
la page 27.  
Visionnez la vidéo d’enregistrement au réseau Wi-Fi à wifithermostat.com/videos  
6
9-2715EF—07  
26  
href="
Connexion à votre réseau Wi-Fi  
1
Connectez votre thermostat.  
1
1
1
a Assurez-vous que le centre des messages du  
thermostat affiche Wi-Fi SETUP (Configuration  
Wi-Fi).  
b Sur votre appareil sans fil (ordinateur portatif,  
tablette, téléphone intelligent), consultez la liste  
des réseaux sans fil disponibles  
Inside  
MORE  
c Connectez-vous au réseau appelé  
NewThermostat_123456 (le chiffre variera).  
Remarque : s’il vous est demandé de spécifier  
un réseau domestique, publique ou de bureau,  
sélectionnez Réseau domestique  
2
7
69-2715EF—07  
href="
Connexion à votre réseau Wi-Fi  
2
Joignez votre réseau domestique.  
2
a Ouvrez votre navigateur Web pour accéder à la  
page de configuration Wi-Fi du thermostat. Le  
navigateur devrait automatiquement vous diriger  
vers la page correcte; s’il ne le fait pas, entrez  
l’adresse http://192.168.1.1  
2b Trouvez le nom de votre réseau domestique sur  
cette page et sélectionnez-le.  
Remarque : Certains routeurs ont des caractéristiques  
améliorées tels que les réseaux invités; utilisez votre  
réseau domestique.  
2c Suivrez les instructions d’enregistrement à votre  
réseau Wi-Fi et cliquez sur le bouton Connect (Connexion). (En fonction de la  
configuration de votre réseau, vous verrez peut-être une instruction vous demandant  
d’entrer le mot de passe de votre réseau domestique.)  
Remarque : Si vous n’avez pas correctement branché le thermostat, la page du routeur  
domestique s’affichera peut-être. Si c’est le cas, revenez à l’étape 1.  
6
9-2715EF—07  
28  
Connexion à votre réseau Wi-Fi  
Remarque : Si votre réseau Wi-Fi n’apparaît pas dans la liste de la page de  
configuration Wi-Fi du thermostat :  
 Essayez de scanner le réseau à nouveau en appuyant sur le bouton Rescan  
nouveau balayage). Ceci est utile dans les endroits avec plusieurs réseaux.  
(
 Si vous êtes connecté à un réseau invisible, entrez alors le SSID du réseau dans  
la boîte de dialogue, sélectionnez le type d’encryptage à partir du menu déroulant,  
et cliquez sur le bouton Add (ajouter). Ceci ajoute manuellement le réseau en tête  
de la liste. Cliquez sur le nouveau réseau de la liste et entrez le mot de passe si  
nécessaire. Cliquez sur Connect (connecter) pour joindre le réseau.  
2
9
69-2715EF—07  
href="
Connexion à votre réseau Wi-Fi  
3
Vérifiez si votre thermostat est connecté.  
Le centre des messages de votre thermostat affiche  
maintenant CONNECTING… (Connexion en cours)  
pour 30 secondes maximum.  
Inside  
Regardez l’écran du thermostat. Vérifiez que le  
centre des messages affiche l’un des messages  
suivants :  
MORE  
CONNECTION SUCCESSFUL (Connexion réussie)  
JOINED: (Vous avez rejoint :) [NOM DU RÉSEAU WI-FI]  
YOU ARE ALMOST DONE (Vous avez presque terminé)  
REGISTER AT TOTAL CONNECT (Inscrivez-vous à Total Connect)  
Si vous voyez l’un de ces messages, passez à page 31.  
Remarque : Si CONNECTION FAILURE (Échec de la connexion) ou Wi-Fi SETUP  
Configuration Wi-Fi) s’affiche dans le centre des messages, confirmez que vous avez  
(
correctement entré le mot de passe de votre réseau domestique à l’étape 2c. Si oui,  
consultez la Foire aux questions à wifithermostat.com/support  
6
9-2715EF—07  
30  
href="
Enregistrement de votre thermostat en ligne  
Pour visualiser et régler votre thermostat Wi-Fi à  
distance, vous devez posséder un compte Total  
Connect Comfort. Voici comment procéder.  
1
Ouvrez le site web Total Connect Comfort.  
Allez sur le site  
www.mytotalconnectcomfort.com  
Visionnez la vidéo d’enregistrement  
du thermostat Wi-Fi à  
wifithermostat.com/videos  
3
1
69-2715EF—07  
href="
Enregistrement de votre thermostat en ligne  
2
Ouvrez une session ou créez un compte.  
Si vous possédez un compte,  
cliquez sur Login (Ouvrir une session)  
ou –  
cliquez sur Create An Account  
créer un compte)  
(
2
2
a Suivez les instructions à l’écran.  
b Consultez votre messagerie et  
recherchez le message d’activation  
provenant de My Total Connect Comfort.  
Ceci peut prendre plusieurs minutes.  
Remarque : Si vous ne recevez aucune  
réponse, consultez votre boîte de pourriels ou  
utilisez une autre adresse électronique.  
2
2
c Suivez les instructions d’activation figurant dans le message.  
d Ouvrez une session.  
6
9-2715EF—07  
32  
href="
Enregistrement de votre thermostat en ligne  
3
Enregistrez votre thermostat Wi-Fi.  
Lorsque vous avez accès à votre compte Total Connect Comfort,  
enregistrez votre thermostat.  
3
a Suivez les instructions à  
l’écran. Après avoir ajouté  
l’emplacement de votre  
thermostat, vous devez entrer  
les identifiants uniques de  
votre thermostat :  
Thermostat ID Card  
Use the MAC ID and CRC ID to register  
this product at mytotalconnectcomfort.com  
HONEYWELL MODEL: RTH8580WF  
MAC ID: MAC CRC:  
Carte d’identification de thermostat  
Utilisez l’identification MAC et l’identification CRC pour  
enregistrer ce produit à mytotalconnectcomfort.com  
Tarjeta de identificación del termostato  
Utilice la identificación MAC y la identificación CRC para  
inscribir este producto en mytotalconnectcomfort.com  
ꢀ MACꢀID  
®
©
U.S. Registered Trademark.  
2012 Honeywell International Inc.  
6
9-2723EFS—01 M.S. 04-12  
ꢀ MACꢀCRC  
Printed in U.S.A.  
69-2723EFS-01  
Remarque : Ces identifiants figurent  
sur la carte d’identification du  
MAC ID  
MAC CRC  
thermostat fournie dans la boîte du thermostat. Ces identifiants ne  
sont pas sensibles à la casse.  
3
3
69-2715EF—07  
href="
Enregistrement de votre thermostat en ligne  
3
b Lorsque le thermostat est  
convenablement enregistré,  
l’écran d’enregistrement Total  
Connect Comfort affiche le  
message SUCCESS (réussi).  
Dans la fenêtre de messages  
du thermostat apparaît :  
CONGRATULATIONS!  
SET UP COMPLETE.  
(Félicitations! Configuration  
terminée.)  
6
9-2715EF—07  
34  
href="
Enregistrement de votre thermostat en ligne  
3
c Veuillez aussi noter que le thermostat  
affiche maintenant la puissance de son  
signal.  
Félicitations! Vous avez terminé.  
Vous pouvez maintenant contrôler votre  
thermostat de n’importe quel endroit au  
moyen de votre ordinateur portatif, de votre  
tablette ou de votre téléphone intelligent.  
Des applications gratuites sont  
®
disponibles pour les appareils iPhone ,  
®
®
®
®
iPad et iPod touch d’Apple sur iTunes  
®
ou sur Google Play pour tous les  
appareils Android.  
GET IT ON  
Download on  
iTunes  
3
5
69-2715EF—07  
href="
Réglage de l’horloge  
1
Appuyez sur CLOCK (horloge) pour afficher les  
flèches de réglage.  
2
Appuyez sur s ou t pour régler l’heure. (Vous  
pouvez avancer plus rapidement en maintenant  
la pression sur les boutons s ou t).  
Appuyez sur DONE (terminé) pour enregistrer  
et quitter (ou sur CANCEL (annuler) pour quitter  
sans modifier l’heure).  
MORE  
3
Remarque : Ce thermostat se mettra à jour  
automatiquement à l’heure d’été/d’hiver (si respecté  
dans votre zone) et l’information de la date/heure  
est enregistrée. Si le thermostat est connecté au  
Wi-Fi et est enregistré au Total Connect Comfort,  
l’heure courante est mise à jour à partir de l’Internet.  
Remarque : pour modifier le format du jour actuel, voir « Options de programme » à la  
page 53.  
6
9-2715EF—07  
36  
href="
Réglage du ventilateur  
1
Appuyez sur FAN (ventilateur) pour  
sélectionner le fonctionnement du ventilateur.  
2
Appuyez à nouveau FAN pour sélectionner  
ON (en fonction) ou AUTO (basculez pour  
resélectionner). L’option sélectionnée  
clignote.  
Inside  
3
Appuyez sur DONE (terminé) pour enregistrer  
le réglage. Votre sélection apparaît sous FAN.  
MORE  
ON : le ventilateur est toujours en fonction.  
AUTO : le ventilateur fonctionne  
uniquement lorsque le système de  
chauffage ou de refroidissement est en  
fonction.  
3
7
69-2715EF—07  
href="
Sélection du mode de fonctionnement du système  
1
2
Appuyez sur SYSTEM (système) pour afficher les options.  
Appuyez à nouveau sur SYSTEM pour  
sélectionner une option. Vous devrez peut-être  
appuyer deux ou trois fois pour effectuer une  
sélection — l’option sélectionnée clignote.  
Appuyez sur DONE (terminé) pour enregistrer le  
réglage.  
Inside  
3
Modes de fonctionnement possibles :  
HEAT (chauffage) : commande uniquement le système  
de chauffage.  
COOL (refroidissement) : commande uniquement le  
système de refroidissement.  
MORE  
OFF (arrêt) : les systèmes de chauffage et de  
refroidissement sont arrêtés.  
AUTO : sélectionne le chauffage ou le refroidissement en  
fonction de la température intérieure.  
Remarque : Les réglages  
de système AUTO et EM HEAT  
peuvent ne pas s’afficher, en  
fonction de la manière dont votre  
thermostat a été installé.  
EM HEAT (thermopompes avec chauffage auxiliaire) :  
commande le chauffage auxiliaire/d’urgence. Le  
compresseur est verrouillé.  
6
9-2715EF—07  
38  
href="
Réglage des programmes  
1
Appuyez sur SCHED (programme) puis sur EDIT  
MORE  
SLEEP  
(
modifier). Les boutons des jours s’affichent sur le  
haut de l’écran.  
2
3
4
Appuyez sur les boutons (MONSUN (lundi-dimanche))  
pour sélectionner les jours.  
Appuyez sur s ou t pour régler l’heure de réveil  
pour le(s) jour(s) sélectionné(s).  
Appuyez sur s ou t pour régler la température de  
chauffage et de refroidissement pour cette période de  
temps.  
5
6
Appuyez sur une autre période (LEAVE (départ),  
RETURN (retour), SLEEP (coucher)) et réglez l’heure et  
les températures de chaque période.  
Appuyez sur DONE (terminé) pour enregistrer et quitter  
(
ou sur CANCEL (annuler) pour quitter sans enregistrer  
SLEEP  
les modifications).  
Remarque : pour annuler toute période non souhaitée,  
appuyez sur CANCEL PERIOD (annuler la période).  
3
9
69-2715EF—07  
href="
Dérogation temporaire de la programmation  
1
Sur l’écran d’accueil, appuyez sur s ou t  
pour ajuster immédiatement la température.  
2
Réglez l’heure jusqu’à laquelle vous voulez  
maintenir la température (l’heure par défaut  
est celle de la fin de la période actuelle).  
Inside  
Temporary Hold  
Le nouveau réglage sera maintenu jusqu’à  
l’heure affichée sous Hold Until (maintenir  
jusqu’à). Lorsque le délai se termine, la  
programmation est rétablie et la température  
revient au réglage correspondant à la  
période actuelle.  
Hold Until  
MORE  
Pour annuler ce réglage temporaire à tout  
moment, appuyez sur CANCEL (annuler)  
(
ou SCHED (programme)). L’horaire de  
programmation est à nouveau en vigueur.  
6
9-2715EF—07  
40  
href="
Dérogation permanente de la programmation  
1
Appuyez sur HOLD (maintien) pour  
régler la température de façon  
permanente. Ceci désactive l’horaire de  
programmation.  
Inside  
2
La température sélectionnée sera  
maintenue 24 heures sur 24 jusqu’à la  
modification manuelle suivante ou une  
pression du bouton CANCEL (annuler)  
Permanent Hold  
MORE  
(
ou SCHED (programme)) afin d’annuler  
le maintien et de revenir à l’horaire de  
programmation.  
4
1
69-2715EF—07  
href="
Réglage du maintien pendant les vacances  
Utilisez cette fonction pour suspendre un horaire de  
Inside  
programmation lorsque vous vous absentez pendant  
une période prolongée.  
1
2
Appuyez sur s ou t pour régler la température.  
Hold Until  
Appuyez sur s ou t pour régler l’heure à  
laquelle vous désirez que la programmation  
reprenne le jour de votre retour.  
MORE  
3
4
Appuyez deux fois sur HOLD (maintien).  
Hold Until (maintenir jusqu’à) s’affiche.  
DAYS  
Appuyez sur s ou t pour sélectionner le nombre  
de jours.  
Hold Until  
La température sélectionnée sera maintenue 24  
heures sur 24 pendant le nombre de jours sélectionné.  
Lorsque le nombre de jours sélectionné s’est écoulé,  
MORE  
l’horaire de programmation précédent est remis en vigueur à l’heure déterminée.  
Remarque : vous pouvez appuyer sur CANCEL (annuler) (ou SCHED (programme))  
pour revenir à la programmation normale.  
6
9-2715EF—07  
42  
href="
Réglage des intervalles de rappel de filtre  
S’il a été activé au cours de l’installation, le rappel  
de filtre affiche un message au-dessus de l’heure  
lorsqu’il est temps de remplacer le filtre.  
Inside  
RESET  
Appuyez sur RESET (réinitialiser) après le  
remplacement du filtre pour relancer la minuterie.  
CHANGE FILTER  
Pour modifier l’intervalle de rappel :  
MORE  
SLEEP  
1
Appuyez sur MORE (plus) puis sur EDIT  
modifier).  
(
2
Appuyez sur s ou t pour sélectionner  
l’intervalle désiré (en jours), puis appuyez sur  
DONE (terminé).  
DAYS  
FILTER  
3
4
Appuyez sur RESET.  
Appuyez sur DONE pour enregistrer et quitter.  
Remarque : La fonction de configuration système 0500 régit l’intervalle de remplacement  
du filtre. Voir « Rappel de remplacement de filtre » à la page 57.  
4
3
69-2715EF—07  
href="
Nettoyage de l’écran  
1
Appuyez sur SCREEN (écran) pour verrouiller  
l’écran en vue du nettoyage. L’écran restera  
verrouillé 30 secondes pour que vous  
puissiez le nettoyer sans modifier des  
réglages.  
MORE  
2
Après 30 secondes, appuyez sur DONE  
(
terminé) pour reprendre le fonctionnement  
normal, ou appuyez à nouveau sur SCREEN  
si vous avez besoin de plus de temps pour le  
nettoyage.  
Remarque : Ne pulvérisez aucun liquide  
directement sur le thermostat. Pulvérisez les  
liquides sur un chiffon, puis utilisez le chiffon  
humide pour nettoyer l’écran. N’utilisez pas d’eau  
ni de nettoyant à vitres ménager. Évitez les  
produits de nettoyage abrasifs.  
6
9-2715EF—07  
44  
href="
Annulation de l’enregistrement du thermostat  
Si vous retirez le thermostat de votre  
compte Total Connect Comfort (par exemple,  
si vous déménagez et laissez le thermostat  
en place), la fenêtre de messages fera  
Inside  
défiler le message UNREGISTERED FROM  
TOTAL CONNECT (enregistrement sur Total  
Connect annulé) pendant 3 minutes.  
MORE  
Après ceci, il affichera alternativement  
REGISTER AT TOTAL CONNECT  
(
enregistrer sur Total Connect) et les codes  
MAC ID et MAC CRC.  
4
5
69-2715EF—07  
href="
Déconnexion Wi-Fi  
Remplacement du routeur  
Si vous déconnectez le thermostat de votre réseau Wi-Fi :  
1
2
Entrez dans la configuration du système (voir page 51).  
Réglez la fonction 900 à 0 (voir page 58).  
Inside  
La fenêtre de messages affichera Wi-Fi DISCONNECTED  
Wi-Fi déconnecté) pendant 1 minute. Il affichera ensuite  
(
MORE  
Wi-Fi SETUP (configuration Wi-Fi).  
Reconnectez-vous à un réseau Wi-Fi en suivant les  
étapes de la page 26.  
Désactivation de la Wi-Fi  
Si vous ne prévoyez pas contrôler le thermostat à distance, vous pouvez supprimer le  
message Wi-Fi SETUP (Configuration Wi-Fi) de l’écran :  
1
2
Entrez dans la configuration du système (voir page 51).  
Réglez la fonction 890 à 0 (voir page 58). La mention Wi-Fi Setup sera supprimée  
de l’écran. Si vous voulez connecter le réseau Wi-Fi plus tard, remettez le paramètre  
8
90 à 1.  
6
9-2715EF—07  
46  
href="
Mises à jour du logiciel  
Honeywell introduit régulièrement des mises à jour du  
logiciel pour ce thermostat. Les mises à jour s’effectuent  
automatiquement par votre connexion Wi-Fi. Tous vos  
réglages sont sauvegardés; vous n’avez donc pas besoin  
de procéder à des changements après la mise à jour.  
Pendant que la mise à jour a lieu, l’écran de votre  
thermostat devient vierge et le centre des messages  
affiche UPDATING (mise à jour) et le pourcentage de la  
mise à jour effectuée. Lorsque la mise à jour est terminée,  
votre écran d’accueil reprend son apparence habituelle.  
Remarque : Si le thermostat n’est pas connecté au  
Wi-Fi et est enregistré au Total Connect Comfort, vous  
n’obtiendrez pas de mises à jour automatiques.  
4
7
69-2715EF—07  
href="
Technologie Smart Response  
Celle-ci permet au thermostat « d’apprendre »  
combien de temps il faut à votre système de  
chauffage/refroidissement pour atteindre le  
réglage de température programmé, afin que  
la température voulue soit obtenue à l’heure  
programmée.  
Par exemple : réglez l’heure de réveil à 6  
heures et la température à 70°. Le chauffage  
est mis en fonction avant 6 heures de manière  
à ce que la température soit de 70° à 6 heures.  
Remarque : la fonction de configuration  
système 0530 contrôle la technologie  
Smart Response. Voir « Technologie Smart  
Le message « Recovery » (reprise)  
Response » à la page 57.  
s’affiche lorsque le système est  
activé avant une période de temps  
programmée.  
6
9-2715EF—07  
48  
href="
Protection du compresseur  
Cette fonction force le compresseur à attendre  
quelques minutes avant un redémarrage, pour  
éviter d’endommager l’équipement.  
Pendant la durée d’attente, le  
message « Wait » (attendre)  
s’affiche à l’écran.  
4
9
69-2715EF—07  
href="
Commutation automatique  
Celle-ci est utilisée dans les climats où le  
conditionnement d’air et le chauffage sont  
utilisés le même jour.  
Lorsque le système est réglé sur AUTO,  
le thermostat sélectionne automatiquement  
le chauffage ou le refroidissement en  
fonction de la température intérieure.  
L’écart entre les réglages de chauffage  
et de refroidissement doit être d’au  
moins 3 degrés. Le thermostat ajuste  
automatiquement les réglages afin de  
maintenir ces 3 degrés d’écart.  
Remarque : la fonction de configuration système  
0
300 contrôle la commutation automatique. Voir  
«
Commutation manuelle/automatique » à la page 56.  
6
9-2715EF—07  
50  
href="
Fonctions et options de configuration  
Vous pouvez modifier des options pour plusieurs fonctions du système. Les fonctions disponibles  
dépendent de votre type de système. Les fonctions, désignées sous forme d’un nombre à quatre  
chiffres, ainsi que les options disponibles sont décrites aux pages 52–58.  
Ce thermostat est préréglé pour un système de chauffage/refroidissement à étage unique.  
La fonction de configuration 0170 pour une thermopompe ajustera les réglages par défaut.  
1
Appuyez sur SYSTEM (système). Vous verrez différents  
boutons vierges s’afficher au bas de l’écran.  
SYSTEM  
HEAT  
2
Appuyez sur le bouton vierge central et maintenez la  
pression jusqu’à ce que l’écran se modifie (environ 5  
secondes).  
6
:30PM  
DONE  
CANCEL  
3
Faites défiler les fonctions en appuyant sur st à  
côté du nombre à quatre chiffres sur la gauche.  
0
120  
20  
4
5
Au besoin, modifiez les options d’une fonction en  
DONE  
appuyant sur st à côté du nombre sur la droite.  
Lorsque toutes les modifications ont été effectuées, appuyez sur DONE (terminé) pour  
enregistrer et quitter.  
5
1
69-2715EF—07  
href="
Configuration du système  
Comment définir le nom de mon thermostat? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
112 Device Name  
52 = Thermostat  
1 Basement  
(
Nom de l’appareil)  
16 Exercise Room 30 Library  
44 Porch  
2
3
4
5
6
7
8
9
Bathroom  
17 Family Room  
18 Fireplace  
19 Foyer  
20 Game Room  
21 Garage  
31 Living Room 45 Rec Room  
32 Lower Level 46 Sewing Room  
33 Master Bath 47 Spa  
48 Storage Room  
35 Media Room 49 Studio  
Ceꢀnomꢀidentifieraꢀleꢀ  
thermostat lorsque  
vous le consultez à  
distance.  
Bathroom 1  
Bathroom 2  
Bathroom 3  
Bedroom  
Bedroom 1  
Bedroom 2  
Bedroom 3  
34 Master Bed  
Si vous enregistrez  
plusieurs  
thermostats,  
22 Great Room  
23 Guest Room  
24 Gym  
25 Kid's Room  
26 Kitchen  
36 Music Room 50 Sun Room  
37 Nursery  
38 Office  
39 Office 1  
40 Office 2  
41 Pantry  
51 Theater  
52 Thermostat  
53 Upper Level  
54 Utility Room  
55 Walk In Closet  
56 Wine Cellar  
57 Workshop  
attribuez un nom  
différent à chacun  
d’entre eux.  
1
1
1
1
1
1
0 Bedroom 4  
1 Boat House  
2 Bonus Room  
27 Kitchen 1  
3 Computer Room 28 Kitchen 2  
42 Play Room  
4 Den  
29 Laundry Room 43 Pool Room  
5 Dining Room  
6
9-2715EF—07  
52  
href="
Configuration du système  
Comment modifier l’heure et la date? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
120 Réglage de l’année 20 = Année 20xx  
deux premiers 21 = Année 21xx  
chiffres)  
(
0
130 Réglage de l’année 0199 (2001–2099)  
deux derniers  
(
chiffres)  
0
0
0
140 Réglage du mois  
0112 (janvier–décembre)  
150 Réglage de la date 0131  
160 Options de  
programmation  
4
0
Horaire de programmation activé (programmable sur 7 jours).  
Horaire de programmation désactivé. Le thermostat ne peut pas être programmé.  
Remarque : Si le thermostat est connecté au Wi-Fi et est enregistré au Total Connect Comfort,  
l’heure courante et la date sont mises à jour à partir de l’Internet. Si vous habitez une zone qui  
respecte l’heure d’été/d’hiver, l’heure est également mise à jour automatiquement.  
5
3
69-2715EF—07  
href="
Configuration du système  
Comment définir mon type de système de chauffage/refroidissement? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
165 Restaurer la  
0
Continuer à utiliser l’horaire programmé.  
programmation par 1 Restaurer le programme du thermostat aux réglages d’économie  
défaut  
d’énergie  
0
170 Sélection du type  
1
Chauffage/refroidissement : chauffage au gaz, au mazout ou électrique  
avec conditionnement d’air central.  
Thermopompe : thermopompe sans chauffage de secours ou auxiliaire.  
Chauffage uniquement avec ventilateur : chauffage au gaz, au mazout  
ou électrique sans conditionnement d’air central.  
Chauffage uniquement (pas de ventilateur) : chauffage au gaz, au  
mazout ou à l’eau chaude sans conditionnement d’air central.  
Refroidissement uniquement : conditionnement d’air central uniquement.  
Thermopompe : thermopompe avec chauffage de secours ou auxiliaire.  
Chauffage/refroidissement multi-étages : 2 étages de chauffage (fils  
sur W et W2), 2 étages de refroidissement (fils sur Y et Y2).  
Chauffage/refroidissement multi-étages : 2 étages de chauffage (fils  
sur W et W2), 1 étage de refroidissement (fils sur Y).  
de système  
2
4
Si vous n’êtes pas  
certain de votre  
type de système  
de chauffage/  
refroidissement  
ou que vous avez  
d’autres questions,  
consultez le site  
wifithermostat.com  
5
6
7
8
9
1
0
Chauffage/refroidissement multi-étages : 1 étage de chauffage (fils sur  
W), 2 étages de refroidissement (fils sur Y et Y2)  
6
9-2715EF—07  
54  
href="
Configuration du système  
Comment personnaliser mon système de chauffage/refroidissement? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
Remarque : en fonction des réglages du système, des fonctions de cette page peuvent ne pas apparaître.  
0
180 Commande du  
ventilateur de  
chauffage  
0
Chauffage au gaz ou au mazout : utilisez ce réglage en cas de système  
de chauffage au gaz ou au mazout (le système contrôle le fonctionnement  
du ventilateur).  
Chauffage électrique : utilisez ce réglage en cas de système de chauffage  
électrique (le thermostat contrôle le fonctionnement du ventilateur).  
1
0
0
190 Vanne de commuta-  
Vanne de commutation de refroidissement : utilisez ce réglage si vous  
tion de thermopompe  
avez connecté un fil étiqueté « O » à la borne O/B.  
pour thermopompes 1 Vanne de commutation de chauffage : utilisez ce réglage si vous avez  
connecté un fil étiqueté « B » à la borne O/B.  
(
uniquement)  
0
240 Cycle de chauffage  
5
Appareil de chauffage au gaz ou au mazout : appareil de chauffage au  
gaz/mazout standard (rendement inférieur à 90 %).  
9
3
Appareil de chauffage électrique : systèmes de chauffage électriques.  
Appareil de chauffage à eau chaude ou à haut rendement : système à eau  
chaude ou appareil de chauffage au gaz (rendement supérieur à 90 %).  
Système à vapeur ou à gravité au gaz/mazout : systèmes de chauffage à  
vapeur ou à gravité.  
0
250 Cycle de chauffage,  
étape 2  
1
5
5
69-2715EF—07  
href="
Configuration du système  
Quelles autres fonctions puis-je modifier? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
280 Rétroéclairage  
0
Rétroéclairage éteint, puis allumé pendant environ 8 secondes après  
pression d’une touche.  
1
Rétroéclairage toujours allumé à basse intensité, luminosité maximum  
après pression d’une touche.  
0
300 Commutation  
manuelle/automa-  
tique  
0
1
Commutation manuelle (Chauffage/Refroidissement/Arrêt).  
Commutation automatique (Chauffage/Refroidissement/Auto/Arrêt). Active  
automatiquement le chauffage ou le refroidissement en fonction de la  
température de la pièce. Remarque : le système maintient une différence  
minimale de 3 °F entre les réglages de chaleur et de refroidissement.  
Voir la page 50  
pour de plus amples  
informations.  
0
320 Unité de  
0
1
Fahrenheit  
Celsius  
température (°F/°C)  
0
330 Réglage  
automatique de  
l’heure d’été  
0
1
Arrêt  
En marche  
6
9-2715EF—07  
56  
href="
Configuration du système  
Quelles autres fonctions puis-je modifier? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
500 Rappel de  
0
Arrêt (pas de rappel)  
remplacement du  
1
2
3
4
5
6
7
8
Rappel après 10 jours de fonctionnement (environ 1 mois calendrier)  
Rappel après 30 jours de fonctionnement (environ 3 mois calendrier)  
Rappel après 60 jours de fonctionnement (environ 6 mois calendrier)  
Rappel après 90 jours de fonctionnement (environ 9 mois calendrier)  
Rappel après 120 jours de fonctionnement (environ 1 an calendrier)  
Rappel après 180 jours de fonctionnement (environ 18 mois calendrier)  
Rappel après 270 jours de fonctionnement (environ 2 ans calendrier)  
Rappel après 365 jours de fonctionnement (environ 3 ans calendrier)  
filtre  
Le rappel après le  
nombre de jours  
de fonctionnement  
sélectionné, et non  
pas du nombre de  
jours réel.  
0
530 Technologie Smart  
1
0
En marche  
Arrêt  
Response  
Voir la page 48  
pour de plus amples  
informations.  
0
640 Format de l’horloge 12 Format 12 heures (par exemple « 3:30 pm »)  
Format 24 heures (par exemple « 15:30 »)  
2
4
5
7
69-2715EF—07  
href="
Configuration du système  
Comment modifier mes paramètres Wi-Fi? (Voir la page 51 pour les instructions.)  
Fonction  
Réglages et Options  
0
710 Restauration des  
0
1
Non  
réglages originaux  
Déconnecte le thermostat du réseau Wi-Fi et restaure les réglages  
d’origine (efface les personnalisations).  
0
890 Wi-Fi  
1
0
Le Wi-Fi est en marche et le thermostat peut être connecté à un réseau Wi-Fi  
Le Wi-Fi est en marche. Le thermostat ne peut pas être connecté à un  
réseau Wi-Fi. Si vous ne connectez pas le thermostat à un réseau Wi-Fi,  
le texte « Wi-Fi Setup » (configuration Wi-Fi) sera supprimé de la fenêtre  
de messages.  
En marche/Arrêt  
0
900 Connexion Wi-Fi  
1
0
Connecté au réseau Wi-Fi. Il s’agit de la configuration automatique  
lorsque le thermostat est connecté au réseau Wi-Fi.  
Sélectionnez 0 pour le déconnecter du réseau Wi-Fi.  
6
9-2715EF—07  
58  
Questions fréquemment posées  
Q : Mon thermostat fonctionnera-t-il toujours si je perds ma connexion Wi-Fi?  
R : Oui, le thermostat actionnera votre système de chauffage et/ou de refroidissement avec ou sans  
Wi-Fi.  
Q : Comment puis-je trouver le mot de passe de mon routeur?  
R : Contactez le fabricant du routeur.  
Q : Pourquoi ne vois-je pas ma page de configuration Wi-Fi?  
R : Vous êtes probablement uniquement connecté à votre routeur, et non pas à votre thermostat.  
Essayez de vous reconnecter au thermostat.  
Q : Pourquoi mon thermostat ne se connecte-t-il pas à mon routeur Wi-Fi même si celui-ci est  
très proche du thermostat?  
R : Vérifiez si le mot de passe saisi pour le routeur Wi-Fi est correct.  
5
9
69-2715EF—07  
Questions fréquemment posées  
Q : Où puis-je trouver mes codes MAC ID et MAC CRC?  
R : Les codes MAC ID et MAC CRC seront affichés dans la fenêtre de messages du thermostat.  
Les numéros figurent également sur une carte jointe au thermostat ou sur l’arrière du thermostat  
(
visibles lorsque celui-ci est retiré de la plaque murale). Chaque thermostat est doté de codes  
MAC ID et MAC CRC uniques.  
Q : Il est impossible d’enregistrer mon thermostat sur le site Total Connect Comfort.  
R : Vérifiez si le thermostat est correctement inscrit dans le réseau Wi-Fi domestique. La fenêtre de  
messages affichera « CONNECTION SUCCESSFUL » (connexion réussie) ou « REGISTER  
AT TOTAL CONNECT » (enregistrer sur Total Connect). Vous devriez également voir l’icône de  
force de signal Wi-Fi. Vérifiez si le routeur Wi-Fi dispose d’une bonne connexion internet. Sur  
votre ordinateur, vérifiez si vous pouvez ouvrir la page mytotalconnectcomfort.com Si vous ne  
pouvez pas l’ouvrir, coupez votre modem internet pendant quelques secondes, puis rallumez-le.  
6
9-2715EF—07  
60  
Questions fréquemment posées  
Q : Je suis enregistré sur le site Total Connect Comfort mais je n’ai pas pu ouvrir de session  
en utilisant mon nouveau compte.  
R : Consultez votre messagerie et vérifiez si vous avez reçu le message d’activation. Suivez les  
instructions d’activation de votre compte, puis ouvrez une session sur le site web.  
Q : Je me suis enregistré sur le site Total Connect Comfort et n’ai pas reçu de message de  
confirmation.  
R : Vérifiez si le message ne se trouve pas dans le dossier des spams ou des messages effacés.  
Q : Y a-t-il un moyen d’accroître la force du signal?  
R : La plupart des routeurs peuvent être configurés comme répéteur. Vous pouvez également  
acheter et installer un répéteur Wi-Fi.  
Pour plus de questions fréquemment posées, consultez le site wifithermostat.com  
6
1
69-2715EF—07  
href="
Messages de la fenêtre de messages  
La fenêtre de messages du sommet de l’écran indique la connexion Wi-Fi et le  
statut d’enregistrement. Il affiche également les codes MAC ID et MAC CRC pour  
l’enregistrement du thermostat sur le site mytotalconnectcomfort.com  
Affiché avant le début de la configuration Wi-Fi.  
Affiché lors de la connexion au réseau Wi-Fi.  
Affiché après la connexion au réseau Wi-Fi.  
[
nom du réseau Wi-Fi]  
Affiché lorsque vous êtes connecté au réseau Wi-Fi.  
Affiché lorsque la connexion Wi-Fi est réalisée.  
Affiché lorsque le thermostat ne parvient pas à établir une  
connexion au réseau Wi-Fi.  
Affiché lorsque le thermostat est connecté au réseau Wi-Fi mais  
n’est pas enregistré sur le site mytotalconnectcomfort.com  
[
[
Sur la carte d’identification]  
Sur la carte d’identification]  
Affiche les codes MAC ID et MAC CRC du thermostat pour  
l’enregistrement sur le site mytotalconnectcomfort.com  
6
9-2715EF—07  
62  
href="
Messages de la fenêtre de messages  
Affiché lorsque le thermostat est enregistré sur le site  
mytotalconnectcomfort.com  
Affiché lorsque le thermostat est retiré de votre compte Total  
Connect Comfort.  
Force du signal Wi-Fi. Affiché lorsque le thermostat  
est connecté au réseau Wi-Fi et enregistré sur le site  
mytotalconnectcomfort.com  
Affiché en cas d’absence de signal Wi-Fi.  
ꢀ VérifiezꢀunꢀautreꢀdispositifꢀpourꢀvousꢀassurezꢀqueꢀleꢀWi-Fiꢀ  
fonctionne dans votre domicile; si non, appelez votre  
fournisseur d’accès Internet.  
ꢀ Déplacezꢀleꢀrouteur.  
ꢀ Redémarrezꢀleꢀthermostatꢀ:ꢀretirez-leꢀdeꢀlaꢀplaqueꢀmurale,ꢀ  
attendez 5 secondes, et emboîtez-le à nouveau sur la  
plaque murale. Retournez à l’étape 1 de Connexion à votre  
réseau Wi-Fi.  
6
3
69-2715EF—07  
href="
Messages de la fenêtre de messages  
Affiché si le mot de passe Wi-Fi du réseau domestique n’a  
pas été entré correctement.  
ꢀ SaisissezꢀdeꢀnouveauꢀleꢀmotꢀdeꢀpasseꢀduꢀréseauꢀWi-Fiꢀdeꢀ  
votre maison.  
ꢀ Répétezꢀleꢀprocessusꢀdeꢀconfigurationꢀetꢀconfirmezꢀleꢀmotꢀ  
de passe du réseau Wi-Fi de votre maison.  
Affiché si aucune adresse IP n’a été fournie par le routeur.  
ꢀ Patientezꢀpendantꢀ30ꢀminutes,ꢀlaꢀconnexionꢀpeutꢀprendreꢀ  
plusieurs minutes. S’il n’y a toujours pas de connexion,  
retirez le thermostat de la plaque murale pendant 5  
secondes, puis raccrochez-le.  
ꢀ Assurez-vousꢀqueꢀvotreꢀrouteurꢀestꢀcorrectementꢀconfiguréꢀ  
pour fournir automatiquement les adresses IP.  
Affiché en cas d’absence de signal Wi-Fi.  
ꢀ Assurez-vousꢀqueꢀleꢀcâbleꢀInternetꢀestꢀbranché.  
ꢀ Redémarrezꢀleꢀrouteur.  
6
9-2715EF—07  
64  
href="
Dépannage  
En cas de difficultés avec le thermostat, essayer les suggestions suivantes.  
La plupart des problèmes peuvent être réglés rapidement et facilement.  
Rien n’apparaît à  
l’écran  
•ꢀ Vérifiezꢀleꢀdisjoncteurꢀetꢀréinitialisez-leꢀsiꢀnécessaire.  
•ꢀ Assurez-vousꢀqueꢀl’interrupteurꢀdeꢀmarche-arrêtꢀduꢀsystèmeꢀdeꢀ  
chauffage et de refroidissement est sur marche.  
ꢀ Assurez-vousꢀqueꢀlaꢀporteꢀdeꢀl’appareilꢀdeꢀchauffageꢀestꢀbienꢀfermée.  
ꢀ VérifiezꢀsiꢀleꢀfilꢀCꢀestꢀconnectéꢀ(voirꢀpageꢀ13).  
Impossible  
de changer  
le réglage du  
système à  
•ꢀ Vérifiezꢀlaꢀfonction 0170 : Type de système pour vous assurer qu’elle  
soit configurée en fonction de votre équipement de chauffage et de  
refroidissement (voir page 54).  
Refroidissement  
Le ventilateur  
ne tourne pas  
lorsque de la  
chaleur est  
requise  
•ꢀ Vérifiezꢀlaꢀfonction 0180 : Commande du ventilateur de chauffage pour  
vous assurer qu’elle soit configurée en fonction de votre équipement de  
chauffage (voir page 55).  
6
5
69-2715EF—07  
href="
Dépannage  
«
Wait » (attendre) •ꢀLaꢀfonctionꢀdeꢀprotectionꢀduꢀcompresseurꢀestꢀactivée.ꢀAttendezꢀ5ꢀ  
minutes que le système se remette en marche en toute sécurité sans  
endommager le compresseur.  
s’affiche à l’écran.  
La thermopompe  
émet de l’air  
frais en mode  
•ꢀ Vérifiezꢀlaꢀfonction 0190 : Vanne de commutation de thermopompe pour  
vous assurer qu’elle soit configurée en fonction de votre équipement de  
chauffage (voir page 55).  
chauffage, ou de  
l’air chaud en mode  
refroidissement  
Le bouton du coin •ꢀ Ceꢀboutonꢀresteꢀviergeꢀsaufꢀsiꢀleꢀrappelꢀdeꢀremplacementꢀdeꢀfiltreꢀdeꢀ  
inférieur droit de  
l’écran est vierge  
appareil de chauffage est activé (voir page 43).  
Le témoin rouge  
est allumé  
•ꢀ SiꢀleꢀthermostatꢀestꢀenꢀmodeꢀChauffageꢀd’urgence,ꢀleꢀtémoinꢀrougeꢀestꢀ  
normal. Il indique que le thermostat est en mode de chauffage d’urgence.  
ꢀ Siꢀleꢀthermostatꢀn’estꢀpasꢀenꢀmodeꢀChauffageꢀd’urgence,ꢀcontactezꢀunꢀ  
réparateur qualifié et faites-le réparer.  
6
9-2715EF—07  
66  
href="
Dépannage  
Le système de  
chauffage ou de  
refroidissement  
ne répond pas  
•ꢀ AppuyezꢀsurꢀSYSTEM (système) pour régler le système sur Heat (chauffage).  
Vérifiez si le réglage de température est supérieur à la température  
intérieure.  
•ꢀ AppuyezꢀsurꢀSYSTEM pour régler le système sur Cool (refroidissement).  
Vérifiez si le réglage de température est inférieur à la température intérieure.  
ꢀ Vérifiezꢀleꢀdisjoncteurꢀetꢀréinitialisez-leꢀsiꢀnécessaire.  
ꢀ Assurez-vousꢀqueꢀl’interrupteurꢀdeꢀmarche-arrêtꢀduꢀsystèmeꢀdeꢀchauffageꢀ  
et de refroidissement est sur marche.  
ꢀ Assurez-vousꢀqueꢀlaꢀporteꢀdeꢀl’appareilꢀdeꢀchauffageꢀestꢀbienꢀfermée.  
ꢀ Siꢀ«ꢀWaitꢀ»ꢀ(attendre)ꢀs’affiche,ꢀlaꢀminuterieꢀdeꢀprotectionꢀduꢀcompresseurꢀ  
est activée. Attendez 5 minutes que le système se remette en marche en  
toute sécurité sans endommager le compresseur (voir page 48).  
Le système  
de chauffage  
fonctionne  
•ꢀ Vérifiezꢀlaꢀfonction 0170 : Type de système pour vous assurer qu’elle  
soit configurée en fonction de votre équipement de chauffage et de  
refroidissement (voir page 54).  
en mode  
refroidissement  
6
7
69-2715EF—07  
Glossaire  
Fil C  
Le fil « C », ou neutre, amène l’alimentation 24 V ca au thermostat à partir du système de chauffage/  
refroidissement. Certains anciens thermostats mécaniques ou à pile peuvent ne pas être dotés de ce  
fil. Il est nécessaire à l’établissement d’une connexion Wi-Fi à votre réseau domestique.  
Système de chauffage/refroidissement à thermopompe  
Des thermopompes sont utilisées pour chauffer et refroidir un immeuble. Si votre ancien thermostat  
comporte un réglage pour chauffage auxiliaire ou d’urgence, vous avez probablement une thermopompe.  
Système de chauffage/refroidissement conventionnel  
Systèmes sans thermopompe ; ceux-ci incluent des appareils de traitement d’air, des appareils de  
chauffage ou des chaudières qui fonctionnent au gaz naturel, au mazout ou à l’électricité. Ils peuvent  
ou non inclure un appareil de conditionnement d’air.  
Cavalier  
Un petit morceau de fil reliant deux bornes ensemble.  
MAC ID, MAC CRC  
Codes alphanumériques identifiant de manière unique votre thermostat.  
®
QR Code  
Code de réponse rapide. Une image bidimensionnelle lisible par une machine. Votre appareil sans fil  
peut lire le motif noir et blanc inséré dans le carré et connecter directement son navigateur à un site  
web. QR Code est une marque déposée de DENSO WAVE INCORPORATED.  
6
9-2715EF—07  
68  
Informations réglementaires  
Déclaration de conformité à la FCC (partie 15.19)  
sont conçues pour fournir une protection raisonnable  
contre les interférences nuisibles dans une installation  
résidentielle. Cet équipement génère, utilise et peut  
émettre de l’énergie de radiofréquence, et s’il n’est pas  
installé et utilisé conformément aux instructions, peut  
causer des interférences nuisibles aux communications  
radio. Il n’y a toutefois aucune garantie qu’une  
(
États-Unis uniquement)  
Cet appareil est conforme à la partie 15 du règlement  
de la FCC. Son fonctionnement est soumis aux deux  
conditions suivantes :  
1
Ce dispositif ne doit pas causer d’interférences  
nuisibles, et  
interférence ne se produira pas dans une installation  
particulière. Si cet équipement cause des interférences  
nuisibles à la réception radio et télévision, ce qui  
peut être déterminé en éteignant le dispositif et en le  
2
Ce dispositif doit accepter toutes les interférences  
reçues, y compris celles pouvant causer un  
fonctionnement non souhaité.  
Avertissement de la FCC (partie 15.21) (États-Unis remettant en marche, il est recommandé à l’utilisateur  
uniquement)  
de tenter de corriger l’interférence par l’une des mesures  
Toute modification qui n’est pas autorisée expressément suivantes :  
par la partie responsable de la conformité de l’appareil  
peut rendre l’utilisateur inapte à faire fonctionner  
l’équipement.  
ꢀ Réorienterꢀouꢀdéplacerꢀl’antenneꢀréceptrice.  
ꢀ Augmenterꢀlaꢀséparationꢀentreꢀl’équipementꢀetꢀleꢀ  
récepteur.  
Déclaration relative aux interférences de la FCC  
•ꢀ Brancherꢀl’équipementꢀdansꢀlaꢀpriseꢀd’unꢀcircuitꢀ  
différent de celui auquel le récepteur est connecté.  
•ꢀ Consulterꢀleꢀdistributeurꢀouꢀunꢀtechnicien  
radio/TV compétent pour obtenir de l’aide.  
(
partie 15.105 (b)) (États-Unis uniquement)  
Cet équipement a été testé et est conforme aux limites  
des dispositifs numériques de Classe B, conformément  
à la Partie 15 du règlement de la FCC. Ces limites  
6
9
69-2715EF—07  
Informations réglementaires  
Thermostats  
Section 7.1.3 de RSS-GEN  
Pour être conformes aux limites d’exposition aux  
Le fonctionnement est soumis aux deux conditions  
radiofréquences établies par FCC et Industrie Canada  
suivantes :  
pour le grand public/l’exposition non contrôlée, la ou les 1 Ce dispositif ne doit pas causer d’interférences, et  
antennes utilisées pour ces transmetteurs doivent être  
installées à au moins 20 cm de toutes les personnes et  
ne peuvent être situées au même endroit qu’une autre  
antenne ou fonctionner conjointement avec une autre  
antenne ou un autre transmetteur.  
2 Ce dispositif doit accepter toutes les interférences, y  
compris celles pouvant causer un fonctionnement non  
souhaité.  
Section 7.1.2 de RSS-GEN  
Conformément aux normes d’Industrie Canada,  
ce transmetteur radio ne peut fonctionner qu’avec  
une antenne dont le type et le gain maximum sont  
approuvés par Industrie Canada. Pour réduire les  
risques d’interférence s radio encourus par d’autres  
utilisateurs, le type et le gain de l’antenne doivent  
être choisis de façon à ce que la puissance rayonnée  
isotrope équivalente (p.i.r.e.) ne soit pas supérieure  
à celle nécessaire à l’établissement d’une bonne  
communication.  
6
9-2715EF—07  
70  
Garantie limitée d’un an  
Honeywell garantit ce produit, à l’exception des piles, contre tout défaut de pièce ou de main-d’œuvre, durant une période d’un (1) an  
à partir de la date d’achat par le consommateur si le produit est utilisé et entretenu convenablement. En cas de défectuosité ou de  
mauvais fonctionnement pendant la période de garantie, Honeywell remplacera ou réparera le produit, à sa discrétion.  
Si le produit est défectueux,  
(
i) le renvoyer avec la facture ou une autre preuve d’achat date au lieu d’achat; ou  
(
ii) appeler le service à la clientèle de Honeywell en composant le 1-855-733-5465. Le service à la clientèle déterminera si le produit  
doit être retourné à l’adresse suivante : Honeywell Return Goods, Dock 4MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422,  
ou si un produit de remplacement peut vous être expédié.  
La présente garantie ne couvre pas les frais de retrait ou de réinstallation. La présente garantie ne s’appliquera pas s’il est  
démontré par Honeywell que la défectuosité ou le mauvais fonctionnement sont dus à un endommagement du produit alors que le  
consommateur l’avait en sa possession.  
La responsabilité exclusive de Honeywell se limite à réparer ou à remplacer le produit conformément aux modalités susmentionnées.  
HONEYWELL N’EST EN AUCUN CAS RESPONSABLE DES PERTES OU DOMMAGES, Y COMPRIS LES DOMMAGES INDIRECTS  
OU ACCESSOIRES DÉCOULANT DIRECTEMENT OU INDIRECTEMENT D’UNE VIOLATION QUELCONQUE D’UNE GARANTIE,  
EXPRESSE OU TACITE, APPLICABLE AU PRÉSENT PRODUIT, OU TOUTE AUTRE DÉFECTUOSITÉ DU PRÉSENT PRODUIT.  
Certaines provinces ne permettent pas l’exclusion ou la restriction des dommages indirects ou accessoires et, par conséquent, la  
présente restriction peut ne pas s’appliquer.  
CETTE GARANTIE EST LA SEULE GARANTIE EXPRESSE FAITE PAR HONEYWELL POUR CE PRODUIT. LA DURÉE DE TOUTE  
GARANTIE IMPLICITE, INCLUANT LES GARANTIES DE QUALITÉ MARCHANDE OU D’ADAPTATION À UNE UTILISATION  
PARTICULIÈRE, EST LIMITÉE PAR LES PRÉSENTES À LA PÉRIODE D’UNE ANNÉE DE LA PRÉSENTE GARANTIE. Certaines  
provinces ne permettent pas de limiter la durée des garanties tacites et, par conséquent, la présente limitation peut ne pas s’appliquer.  
La présente garantie donne au consommateur des droits spécifiques et certains autres droits qui peuvent varier d’une province à l’autre.  
Pour toute question concernant la présente garantie, prière d’écrire aux Services à la clientèle de Honeywell à l’adresse suivante :  
Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 ou composer le 1-855-733-5465.  
7
1
69-2715EF—07  
href="
Systèmes d’automatisation et de régulation  
Honeywell International Inc.  
6
9-2715EF-07  
1
985 Douglas Drive North  
Golden Valley, MN 55422  
Honeywell Ltd  
7
05 Montrichard Avenue  
Saint-Jean-sur-Richelieu, Québec  
J2X 5K8  
wifithermostat.com  
®
Marque de commerce déposée américaine.  
Apple, iPhone, iPad, iPod touch et iTunes sont  
des marques de commerce de Apple Inc.  
Toutes les autres marques de commerce sont  
propriété de leurs propriétaires respectifs.  
©
6
2013 Honeywell International Inc.  
9-2715EF—07 M.S. Rev. 11-13  
Imprimé aux États-Unis  

Lux Products ELV1PSPLV510 Thermostat User Manual

Honeywell T8034C Thermostat User Manual

Aube TH144 Thermostat User Manual

Honeywell YCT87N1006 Thermostat User Manual

Lux Products TH10 Thermostat User Manual

Aube TH110A SP P Thermostat User Manual

Honeywell TZ 4 Thermostat User Manual

Aube TH114 Thermostat User Manual

Honeywell RTH6300B Thermostat User Manual

Aube TH102D Thermostat User Manual