Trane TCONT624AS42DA Thermostat User Manual

Home

href="
32-5088-01  
Touchscreen  
Comfort Control  
Model TCONT624AS42DA  
User Guide  
Nexia Home Intelligence  
Customer Service:  
(877) 288-7707  
For HVAC related  
issues, contact your  
servicing dealer  
Î NOTE: A 24 Volt common and hot wire MUST be  
connected to the TCONT624A for operation.  
Contents  
User Guide  
Features ..........................................................................................................................................................................2  
Operation .........................................................................................................................................................................3  
User Settings ...................................................................................................................................................................4  
Scheduling .......................................................................................................................................................................5  
Enrolling into “Z-Wave” Network (NexiaTM Home Intelligence).........................................................................................8  
Un-enroll comfort control from existing “Z-Wave” Network (NexiaTM Home Intelligence).................................................9  
Firmware Upgrades .......................................................................................................................................................10  
About .............................................................................................................................................................................11  
Clean Screen ................................................................................................................................................................11  
Limited Warranty............................................................................................................................................................12  
FCC/IC Notice................................................................................................................................................................14  
1
href="
User Guide  
Features  
TCONT624AS42DA Features  
24v, Z-Wave comfort control  
Remote access via smart phone, tablet, or P.C. (requires SK101 and a NexiaTM Home Intelligence account).  
Interactive 4.3” black & white touchscreen  
7 Day programmable, 4 schedules/day  
Built in humidity sensor with RH display  
Filter, maintenance, humidifier service reminders  
Remote temperature sensing option (1 indoor/1 outdoor)  
Auxiliary & compressor heat lockouts  
Dehumidification (overcooling)  
Enhanced dehumidification (cooling)  
Adjustable variable speed fan settings (pwm)  
Energy Savings Mode (ESM)  
Screen lock and guest lock  
Upgradable firmware (requires a NexiaTM Home Intelligence account).  
Service test modes  
2
href="
User Guide  
Operation  
The model TCONT624AS42DAA Comfort Control provides typical operation of a forced air heating and cooling HVAC system. The TCONT624  
comfort control also features a Z-Wave™ module for remote control.  
:
PM  
F
Cooling  
Auto  
Fan  
Hold  
Cool  
Menu  
Sched  
Mode  
Normally, the Comfort Control displays the Home Screen as shown above.  
Item Description  
Clock Display The current time is displayed in the upper left corner  
of the main screen. The time will blink when the clock is connected to Nexia Home Intelligence the clock will  
Notes  
See TIME/DATE for more information. If the control  
has not been set.  
be updated by the Nexia portal.  
Dynamic Labels and Func- The buttons are defined by the dynamic labels in each  
tion Control Buttons  
button. As you navigate through menus, the labels for  
the buttons will change.  
Setpoint Display and Set-  
point Up/Down Buttons  
The current heat or cool setpoint is displayed. These  
setpoints may be set using Nexia Home Intelligence,  
The setpoints will push each other if they are adjusted  
to within the minimum heat/cool separation setting.  
the Control’s internal schedule, or by pressing the Set- This is normally 3 degrees.  
point Up/Down buttons. Pressing the setpoint button  
changes the setpoint screen. The current mode is dis-  
played at the top of the screen. Adjust the setpoint by  
pressing the up or down arrows. To change setpoint  
mode press the MODE button.  
Temperature Display  
Menu Button  
The Comfort Control displays the current temperature The internal temperature sensor can be adjusted as  
as sensed by the internal temperature sensor.  
necessary.  
Button used to access other Comfort Control menus  
Other Comfort Control menus can be accessed by  
pressing the MENU button.  
System Mode Button  
Button used to change the system mode  
Off: System off  
Heating: Heating only  
Cooling: Cooling only  
Auto: Heating/Cooling as necessary  
EM Heat: Indoor Heat only  
Fan Mode Button  
Button used to change the fan mode:  
Auto: Fan on when cooling/heating is necessary  
On: Fan constantly on  
Circ: Fan on for a user-selected number of minutes  
per hour.  
Schedule Mode Button  
Button used to change the schedule mode:  
Hold: System maintains the current temperature set-  
points. Schedules are disregarded.  
Run: Run the system schedule  
Energy Saving Mode (ESM): Temperature setpoints in  
ESM Setpoints are maintained.  
3
href="
User Guide  
User Settings  
User Settings allow the user to customize various settings on the 624 control. To access User Settings simply press  
the Menu button once and “User Settings” will be displayed. To enter the User Settings menu, press the Select button,  
then use the Next button to navigate through the options below. The default setting will be shown in brackets. After  
each selection press the Done button to save changes.  
Thermostat  
Setting  
Temperature Scale  
Cooling RH Setpoint  
Range  
[Fahrenheit], Celsius  
30% - 60% [50%]  
Description  
Select the temperature display scale  
Select the desired indoor relative humidity during cooling mode. Dehu-  
midification must be enabled in the Installer Settings for this option to be  
available.  
Smart Continuous Fan  
Continuous Fan Airflow  
Fan Circulate On Time  
Yes, [No]  
If yes is selected, continuous fan mode is disabled when indoor humidity  
exceeds the Cooling RH Setpoint  
35% - 100% [50%]  
1 - 59 minutes, [Off]  
Select the desired fan speed when the Fan Mode selected is Continuous  
(variable speed blower required)  
Select the desired amount of time the fan will cycle per hour when the Fan  
Mode selected is Circ  
Local Schedule Enable  
Max Heat Setpoint  
Min Cooling Setpoint  
H/C Delta  
[Yes], No  
Select whether scheduling will be enabled or disabled  
Select the highest heating setpoint allowed  
55 - [90] Degrees  
[60] - 99 Degrees  
[3] - 15 Degrees  
Select the lowest cooling setpoint allowed  
Select the minimum deadband between Heating and Cooling setpoints  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
Energy Savings Mode  
Setting  
Range  
Description  
ESM Heat Setpoint  
55 - 90 degrees [62]  
Select the desired Heating Setpoint when ESM (Energy Savings Mode) is  
selected  
ESM Cooling Setpoint  
60 - 99 Degrees [85]  
Select the desired Cooling Setpoint when ESM (Energy Savings Mode) is  
selected  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
Display  
Setting  
Range  
[0] - 90 Seconds  
Description  
Screen Timeout  
Select how long after the last button press before the screen timeouts to a  
minimized screen  
Backlight Timeout  
Backlight On Percent  
Backlight Off Percent  
Buzzer Enable  
0 - 90 Seconds [20]  
0 - [100] Percent  
[0] - 100 Percent  
[Yes], No  
Select how long after the last button press before the backlight dims  
Select the screen brightness when the backlight is lit  
Select the screen brightness when the backlight timeout expires  
Select whether button presses are audible  
Security  
[Unlocked], Display Lock, Guest  
Access  
Select security level  
• Unlocked - Enables selection of all menus and settings  
• Display Lock - Disables selection of all menus and settings  
• Guest Access - Disables selection of all menus and settings except the  
following: Raise or lower heating or cooling setpoint +/- 5 degrees and  
change system mode  
Note: When Display Lock or Guest Lock is selected a lock icon will appear  
next to the up arrow.  
Note: To disable Display Lock or Guest Access, press and hold the up  
and down arrows until the lock icon disappears.  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
4
href="
User Guide  
User Settings Continued  
User Settings allow the user to customize various settings on the 624 control. To access User Settings simply press  
the Menu button once and “User Settings” will be displayed. To enter the User Settings menu, press the Select button,  
then use the Next button to navigate through the options below. The default setting will be shown in brackets. After  
each selection press the Done button to save changes.  
Time/Date  
Setting  
Range  
1 - 12 am, 1 - 12 pm  
0 - 59  
Description  
Hour  
Select the current hour of day  
Select current minute of day  
Select current day of week  
Select current year  
Minutes  
Day of Week  
Year  
Sun - Sat  
2013 - 2113  
Jan - Dec  
Month  
Select current month of year  
Select current day of month  
Date  
1 - 31  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
Reminders  
Setting  
Filtration Enable  
Filter Period  
Range  
Description  
Yes, [No]  
Selecting yes, enables the Filter Reminder feature  
[Monthly], Quarterly, Semi-Annu- Select how often the reminder will be displayed  
ally, Annually  
Filter Start Month  
[Jan] - Dec  
Yes, [No]  
Jan - Dec  
Jan - Dec  
Select the Filter Reminder start month  
System Maint Enable  
First Maint Month  
Selecting yes, enables the System Maintenance Reminder feature  
Select the first System Maintenance month  
Second Maint Month  
Select the second System Maintenance month  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
Scheduling  
Schedule Setup Procedure  
The 624 comfort control is preset at the factory with a 7 Day energy savings schedule. Each day of the week is pre-programmed with the  
following schedule:  
Scheduling  
Time  
6:00 AM  
Schedule Name  
Wake  
Heat Temperature Setting  
Cool Temperature Setting  
70 F  
62 F  
70 F  
62 F  
78 F  
85 F  
78 F  
78 F  
8:00 AM  
6:00 PM  
10:00 PM  
Day  
Evening  
Night  
The schedule may be changed locally at the control with the Edit Schedule menu. If the 624 comfort control is connected to Nexia Home  
Intelligence the schedule may be changed remotely from the Nexia website using the website’s Edit Schedule menu.  
5
href="
User Guide  
Scheduling  
Edit Schedule (Local)  
Press the following button sequence to edit or create an entirely new daily schedule.  
Edit Schedule  
Button Press  
Menu Displayed  
What Needs to Be Done?  
Press Menu from Home  
screen  
USER SETTINGS  
Press Next  
SCHEDULE  
Press Select  
Press Select  
Press Select  
EDIT SCHEDULE  
SELECT DAY  
SET TIME  
Continue to press “Next” until the day of week to edit is displayed.  
Set the start time for each of four periods for the day displayed. Use the Up/Down  
buttons to set the start time for the period displayed. Wake is the default period.  
Pressing the “Next” button three times cycles through the period displayed (Wake,  
Day, Evening and Night).  
Press Next  
Press Next  
Press Next  
HEAT SETPOINT  
COOL SETPOINT  
Use the Up/Down arrows to set the Heat set point for the period displayed  
Use the Up/Down arrows to set the Heat set point for the period displayed  
Continue pressing Next and using up/down arrows until all Heat & Cool set points  
are set for the day displayed. After editing a start time or editing the set point  
temperature for one or more periods press “Done” to save edits. If “Done” is not  
pressed edits will not be saved.  
After Pressing Done  
Press Yes to Copy  
Copy Schedule is dis-  
played at the top of the  
screen.  
and No buttons are dis-  
played on the right side of  
the screen.  
Press yes to copy or no to return to Edit Schedule menu.  
Yes  
COPY “_ _ _” To  
is Pressing Yes will copy the day displayed to the next day in the week. If Yes is  
displayed at the top of the pressed five more times the scheduled will be copied to the remaining 5 days in  
screen.  
Yes and  
the week. To skip over a day and avoid copying the schedule to that day press No.  
No buttons are displayed  
on the right side of the  
screen.  
Press Done  
Press Done  
EDIT SCHEDULE  
menu is displayed  
To return to the Home Screen press “Done” one more time.  
Home Screen is displayed  
The schedule may be changed locally at the control with the Edit Schedule menu. If the 624 comfort control is connected to Nexia Home  
Intelligence the schedule may be changed remotely from the Nexia website using the websites Edit Schedule menu.  
6
href="
User Guide  
Scheduling  
Copying Schedules  
Press the following button sequence to access “Copying Schedules” from the Home Screen.  
Copying Schedules  
Button Press  
Menu Displayed  
What Needs to Be Done?  
Menu  
Next  
USER SETTINGS screen  
Select  
Next  
EDIT SCHEDULE screen  
COPY SCHEDULE screen  
Select  
Next  
COPY FROM screen (Mon) Defaults to Monday  
Advances to next day  
Back  
Select  
Goes back to previous day  
Copy To screen  
COPY SCHEDULE  
SCHEDULE  
Select the day to copy to by pressing on Yes or No buttons until the copy to day  
is selected.  
Press Done  
Continue copying one days schedule at a time to another or Press Done until  
the Home Screen Appears  
Press Done  
Press Done  
HOME SCREEN is dis-  
played  
Press Done  
Home Screen is displayed  
The schedule may be changed locally at the control with the Edit Schedule menu. If the 624 comfort control is connected to Nexia Home  
Intelligence the schedule may be changed remotely from the Nexia website using the websites Edit Schedule menu.  
Edit Schedule (Remotely) - from Nexia Home Intelligence  
Go to MyNexia.com, log into your account and select a TCONT624 comfort control from the Climate Page. Click on Edit Schedule and follow  
the online instructions. If you have not set up a Nexia Home Intelligence account go to MyNexia.com and click on “Get Started” to set up an  
account. A router and Nexia Bridge kit (SK101 - includes one Nexia Bridge and one Z-wave module) is required for remote access to the 624  
control. For questions about connecting to Nexia Home Intelligence contact Nexia Home Intelligence Customer Service at 877-288-7707  
7
href="
User Guide  
Enroll Comfort Control into existing Z-Wave Network (NexiaTM Home Intelligence)  
1
Prepare the bridge for enrollment. (Bridge kit SK101 purchased  
separately)  
Î
Note: If the bridge is already installed, follow the instructions as they are  
written in the following steps. If the bridge is not installed, follow the instruc-  
tions shipped with the bridge kit.  
Blue  
light  
a. Unplug Ethernet and power cables from bridge.  
b. Install a quality 9 volt battery.  
c. Verify that blue light is blinking. If blue light is solid, battery is dead.  
d. Take bridge to the location where the Comfort Control is mounted.  
Battery  
2
Enroll the Comfort Control into the bridge. (Inclusion)  
If you are using a controller that is not a NexiaTM bridge, consult the instructions  
that shipped with the controller to find out how to enroll a new device.  
a. Hold the bridge within 6 feet (1.8 meters) of the Comfort Control throughout  
steps “b” through “f”.  
“+” Button  
Î
After you begin the enrollment process, you have 30 seconds to complete  
the remainder of the steps. Study the steps below before beginning.  
b. Press and release the plus (+) button on the bridge.  
c. Press the MENU button on the Comfort Control.  
d. Press the NEXT button to advance to the Z-WAVE menu.  
e. Press SELECT  
f. Observe the lights on the bridge. The orange light will blink while enrollment  
is taking place. Enrollment is complete when the orange light becomes solid.  
3
Verify enrollment of the Comfort Control.  
a. Press Menu Button on the main Comfort Control screen.  
b. Press the Next Button to advance to the About screen and press the Select Button.  
c. Press the Next Button to advance through the menu options to Node ID  
If the number listed there is anything other than “00”, the Comfort Control has been successfully enrolled.  
If the number listed there is “00”, the Comfort Control has NOT been successfully enrolled. In this case, repeat step 18 and verify  
again.  
d. Press Done button 2 times when finished.  
Item  
Description  
VERSION 010000  
ZWAVE VER 034006  
NODE-ID 01  
Firmware version (number may vary)  
Z-Wave version (number may vary)  
Z-Wave node ID (number may vary)  
Z-Wave Home ID (number may vary)  
Outdoor type may be AC, HP or NONE  
HOME-ID 00000000  
OUT-TYPE AC  
C/O WITH COOL  
IN-TYPE GAS/OIL  
Energize Reversing Valve with COOL or with HEAT (HP only)  
Indoor type may be GAS/OIL, ELECTRIC or HYDRONIC  
8
href="
User Guide  
Enroll Comfort Control into existing Z-Wave Network (NexiaTM Home Intelligence) Continued  
4
Establish Online Connection to the Comfort Control.  
Nexia Home Intelligence account must be active before continuing. See nexiahome.com for more information.  
a. Remove the battery from the bridge.  
b. Plug the Ethernet and power cord back into the bridge.  
d. Click the Climate tab and follow the on screen instructions.  
Note: If the new thermostat icon remains gray or cannot be controlled remotely, you might need to add Z-wave repeaters to  
improve communications. Contact your local Nexia expert or call 877-288-7707 for assistance.  
Un-enroll Comfort Control from existing Z-Wave Network (NexiaTM Home Intelligence)  
1
If you need to remove the 624 from a Nexia Home Intelligence account, follow the Exclusion steps. This will delete  
the ability to control the thermostat remotely. If you are unsure, please contact Nexia support at  
877-288-7707.  
Install a new, high-quality 9-volt battery into the bridge.  
a. Hold the bridge within 6 feet (1.8 meters) of the Comfort Control throughout the entire exclusion process.  
Î
After you begin the exclusion process, you have 30 seconds to complete the remainder of the steps. Study the steps below  
before beginning.  
b. Press and release the minus (-) button on the bridge.  
c. Press the MENU button on the Comfort Control.  
d. Press NEXT button to scroll to Z-WAVE screen then press SELECT.  
e. Press the Yes button to exclude the Comfort Control.  
f. Observe the lights on the bridge. The orange light will blink while exclusion is taking place. Exclusion is complete when the orange  
light becomes solid.  
Î
Z-Wave™ controllers from various manufacturers may support the Z-Wave™ Thermostat General V2 Device class used by the  
Z-Wave™ Comfort Control. If you are using a controller that is not a Nexia bridge, consult the instructions that came with the  
controller to find out how to enroll a new device.  
9
href="
User Guide  
Firmware Upgrades  
1
Firmware Upgrades allow the user to update the 624 control. Upgrades may take up to 45 minutes. The system  
operation will be maintained during the upgrade process. To access the Firmware Upgrades navigate to  
mynexia.com and look for the Edit Home screen button. The Edit Home screen button is located about mid way  
own the Nexia Home Page.  
a. On the Edit Home, Firrmware Updates page, the 624 will appear. If a firmware update is available an”Update Firmware” button will  
appear.  
10  
href="
User Guide  
b.  
When the user selects the “Update Firmware” button an “Update Firmware” dialog will appear. The dialog will first  
connect to the device and then it will display the firmware update progress.  
c.  
d.  
e.  
After the firmware has been downloaded it is then applied to the TCONT624.  
The portal retrieves version information from the TCONT624.  
Finally the user is shown that the firmware was updated successfully  
About  
About  
Range  
Setting  
Version  
Current firmware version loaded on the control  
Current version of the ZWAVE firmware  
ZWAVE Ver  
Node - ID  
Home - ID  
Out - Type  
C/O - Type  
In - Type  
ZWAVE identification for this device  
ZWAVE identification for the connected ZWAVE network  
Identifies the type of outdoor unit installed  
Indicates whether the switchover valve (SOV) is energized in cooling or heating mode  
Identifies the type of indoor unit installed  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
Clean Screen  
Clean Screen  
Setting  
Clean Screen  
Range  
Description  
Yes, No  
Selecting yes allows the user to clean the screen without activating any  
of the onscreen touch points. Use only water and a soft cloth, no harmful  
chemicals.  
Once all selections have been made, press the Done button to exit and return to Menu. Press Next to navigate to the next setting.  
11  
href="
Warranty  
Base Limited Warranty  
Subject to the terms and conditions of this limited warranty, Trane U.S., Inc. (“Company’) extends a limited warranty against manufacturing defects for the product(s)  
identified in Tables 1, 1A, 1B attached hereto (“Products’) that are installed in a residential/multi-family application (personal, family or household purposes) under normal  
use and maintenance in the United States and Canada.  
This limited warranty applies to Products manufactured on or after August 1, 2011.  
In order to maximize the available benefits under this limited warranty, the Purchaser (as defined below) should read it in its entirety. All repairs of Product parts  
covered under this limited warranty must be made with authorized service parts and by a licensed HVAC service provider. Additionally, commercial applications are treated  
differently under this limited warranty as stated in Tables 1, 1A, 1B attached hereto. For purposes of this limited warranty, “commercial applications” shall mean any ap-  
plication other than for personal, family, or household use.  
TERM: The limited warranty period for Products is as stated in Tables 1, 1A, 1B attached hereto. If the Purchaser properly registers the Products, the limited warranty  
period shall be extended as stated in Tables 1, 1A, 1B attached hereto. Regardless of registration, the Commencement Date for a limited warranty period shall be the date  
that the original installation is complete and all Product start-up procedures have been properly completed and verified by an installer’s invoice. If the installation and start-  
up date cannot be verified by the installer’s invoice, the Commencement Date shall be sixty (60) days after the factory manufacture date which is verified by the Product  
serial number. Where a Product is installed in a newly constructed home, the Commencement Date is the date the Purchaser purchased the residence from the builder.  
Proof of Product purchase, installation, and/or closing date of the residence may be required to confirm the Commencement Date.  
The installation of Product replacement parts under this limited warranty shall not extend the original warranty period. The warranty period for any Product part re-  
placed under this limited warranty is the applicable warranty period remaining under the original Product warranty.  
WHO IS COVERED: This limited warranty is provided only to the original owner and his or her spouse (“Purchaser’) of the residence where the Products are originally  
installed. This warranty is not transferable except according to terms stated on the applicable website identified below under Registration Requirements. Company has the  
right to request any and all proof of Product purchase or installation and/or closing date of the residence.  
WHAT COMPANY WILL DO: Company may request proof of Product purchase and/or installation in order to provide Product parts under this limited warranty. As  
Company’s only responsibility and Purchaser’s only remedy under this limited warranty, Company will furnish a replacement part to the licensed HVAC service provider,  
without charge for the part only, to replace any Product part that fails due to a manufacturing defect under normal use and maintenance. The Purchaser must pay for any  
and all shipping and handling charges and other costs of warranty service for the replacement part. If a Product part is not available, Company will, at its option, provide a  
free suitable substitute part or provide a credit in the amount of the then factory selling price for a new suitable substitute part to be used by the Purchaser towards the retail  
purchase price of a new Company product. Any new Product purchase shall be at Purchaser’s sole cost and expense including, but not limited to, all shipping, removal,  
and installation costs and expenses.  
REGISTRATION REQUIREMENTS: All Products must be properly registered online by the Purchaser within sixty (60) days after the Commencement Date to receive  
the registered limited warranty terms. To register online, go to:  
and click “Begin Online Registration.” If a Purchaser does not register within this stated time period, the base limited warranty terms shall apply.  
ELIGIBILITY REQUIREMENTS: The following items are required in order for the Products to be covered under this limited warranty:  
The Products must be in the same location where they were originally installed.  
• The Products must be properly installed, operated, and maintained by a licensed HVAC service provider in accordance with the Product specifications or installation,  
operation, and maintenance instructions provided by Company with each Product. Failure to conform to such specifications and/or instructions shall void this limited  
warranty. Company may request written documentation showing the proper preventative maintenance.  
All Product parts replaced by Company under this limited warranty must be given to the servicing provider for return to Company.  
Air handlers, air conditioners, heat pumps, cased or uncased coils and stand-alone furnaces must be part of an Air Conditioning, Heating, and Refrigeration Institute  
rated and matched system or a specification in a Company provided bulletin or otherwise approved in writing by a Company authorized representative.  
EXCLUSIONS: The following are not covered by this limited warranty:  
• Labor costs including, but not limited to, costs for diagnostic calls or the removal and reinstallation of Products and/or Product parts.  
• Shipping and freight expenses required to ship Product replacement parts.  
• Failures, defects, or damage (including, but not limited to, any loss of data or property) caused by (1) any third party product, service, or system connected or used  
in conjunction with the Products; (2) any use that is not designed or intended for the Products; (3) modification, alteration, abuse, misuse, negligence, or accident;  
(4) improper storage, installation, maintenance, or operation including, but not limited to, operation of electrical equipment at voltages other than the range specified  
on the Product nameplate; (5) any use in violation of written instructions or specifications provided by Company; (6) any acts of God including, but not limited to, fire,  
water, storms, lightning, or earthquakes; or any theft or riots; or (7) a corrosive atmosphere or contact with corrosive materials such as, but not limited to, chlorine,  
fluorine, salt (provided that indoor and outdoor coils will only be covered if a Sea Coast Kit is installed), sulfur, recycled waste water, urine, fertilizers, rust, or other  
damaging substances or chemicals.  
• Products purchased direct including, but not limited to, Internet or auction purchases and purchases made on an uninstalled basis.  
• Cabinets or cabinet pieces that do not affect product performance, air filters, refrigerant, refrigerant line sets, belts, wiring, fuses, surge protection devices, non-factory  
installed driers, and Product accessories (unless otherwise specified).  
• Increased utility usage costs.  
REFRIGERANT POLICY: (1) Manufacturer-Installed Refrigerant: Beginning on January 1, 2010, R-22 refrigerant will no longer be used as a manufacturer-  
installed refrigerant as required by federal regulation. All Products with manufacturer-installed refrigerant will include R-410A refrigerant. Any and all expenses  
or costs associated with replacing Product parts that are not R-410A compatible will not be covered by the terms and conditions of this limited warranty. (2)  
Non-Manufacturer installed Refrigerant: For Products manufactured and sold by the Company without refrigerant, only manufacturer approved and genuine  
alternate refrigerants shall be used. The use of contaminated, counterfeit, non-genuine, or non-manufacturer approved alternate refrigerant will void this limited  
warranty. (3) All Products: Products include a liquid line filter drier which must be replaced when a compressor replacement is necessary. A suction line filter  
drier must be added for compressors defined as burnouts and failure to do so will void this warranty. Non-approved refrigerant and/or non-approved refrigerant  
system additives including, but not limited to dyes will void this limited warranty.  
GW-658-2213  
12  
href="
Warranty  
ADDITIONAL TERMS:  
THIS LIMITED WARRANTY AND LIABILITY SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES AND LIABILITIES, WHETHER IN CONTRACT  
OR IN NEGLIGENCE, EXPRESS OR IMPLIED, IN LAW OR IN FACT. THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE ARE LIMITED TO THE DURATION OF THE APPLICABLE PRODUCT WARRANTY. COMPANY DOES NOT AUTHORIZE ANY PERSON TO CREATE FOR  
IT ANY OBLIGATION OR LIABILITY IN CONNECTION WITH THE PRODUCTS.  
NOTWITHSTANDING ANYTHING IN THIS LIMITED WARRANTY TO THE CONTRARY, COMPANY SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSE-  
QUENTIAL, INDIRECT, SPECIAL AND/OR PUNITIVE DAMAGES, WHETHER BASED ON CONTRACT, WARRANTY, TORT (INCLUDING, BUT NOT LIMITED TO,  
STRICT LIABILITY OR NEGLIGENCE), PATENT INFRINGEMENT, OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. COMPANY’S  
MAXIMUM LIABILITY HEREUNDER IS LIMITED TO THE ORIGINAL PURCHASE PRICE OF THE PRODUCTS.  
No action arising out of any claimed breach of this limited warranty may be brought by a Purchaser more than one (1) year after the cause of action has arisen.  
This limited warranty gives you specific legal rights, and you may also have other rights as otherwise permitted by law. If this Product is considered a consumer prod-  
uct, please be advised that some local laws do not allow limitations on incidental or consequential damages, how long a warranty lasts based on registration, or how long  
an implied warranty lasts, so that the above limitations may not fully apply. Refer to your local laws for your specific rights under this limited warranty.  
Consumer Relations  
20 Corporate Woods Dr.  
Bridgeton, MO 63044  
Table 1A: Warranty Time Periods for Controls, Zoning Products, Humidifiers, Energy Recovery Ventilators, Air Cleaners and Oil Furnaces (Variable and Non-  
Variable Speed)  
COVERAGE TERMS FOR RESIDENTIAL APPLICATIONS: Pursuant to the Trane U.S., Inc. (“Company”) limited warranty terms and conditions, the following Products are  
covered for the base time periods as stated below (“Base Limited Warranty period”). If registered, the Base Limited Warranty Periods for certain products will be extended  
as stated below (“Registered Limited Warranty Period”).  
CONTROLS: *CONT200,*CONT401,*CONT402, *CONT600 &*CONT602  
Base Limited Warranty Period: one (1) year  
Registered Limited Warranty Period: five (5) years  
CONTROLS: *ZEMT500, *CONT624, *CONT800,*CONT802,*CONT803, *CONT824, *CONT900, *ZONE940, *ZONE950  
Base Limited Warranty Period: five (5) years  
Registered Limited Warranty Period: ten (10) years  
ZONING PRODUCTS: *ZONE950, *ZONE940, *ZONE930, ZZONEPNLAC52Z, ZZONEEXPAC52Z, ZZSENSAL0400, BAYSEN01ATEMPA, BAY24VRP, ZDAMPRD,  
ZDAMPSM, ZDAMPBM, ZDAMPRR  
Base Limited Warranty Period: five (5) years  
Registered Limited Warranty Period: ten (10) years  
HUMIDIFIERS: *HUMD200, *HUMD300 & *HUMD500  
Base Limited Warranty Period: five (5) years  
Registered Limited Warranty Period: ten (10) years  
ENERGY RECOVERY VENTILATOR (ERV): *ERVR100, *ERVR200 & *ERVR300  
Base Limited Warranty Period: five (5) years  
Registered Limited Warranty Period: ten (10) years  
AIR CLEANERS: TFD & AFD  
Base Limited Warranty Period: five (5) years  
Registered Limited Warranty Period: ten (10) years  
VARIABLE SPEED OIL FURNACE: *HV-V, *LF-V, *LR-V,*DF-V  
Base Limited Warranty Period: Parts- five (5) years, Heat Exchanger - twenty (20) years  
Registered Limited Warranty Period: Parts - ten (10) years, Heat Exchanger - Lifetime  
GW-658-2213  
13  
href="
FCC Notice  
FCC ID WIBTZW012  
INFORMATION TO USER  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired  
operation.  
This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules.  
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment  
generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this  
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and  
on, the user is encouraged to try to correct the interference by one or more of the following measures.  
Reorient or relocate the receiving antenna  
Increase the separation between the equipment and receiver  
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected  
Consult the dealer or an experienced radio/TV technician for help  
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate  
the equipment.  
IC Notice  
IC 9374A-XR624  
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this  
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired  
operation of the device.  
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio  
exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne  
doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage  
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.  
©2013 Trane  
Literature Order Number  
File number  
32-5088-01  
32-5088-01  
New  
Trane  
Supersedes  
6200 Troup Highway  
Tyler, TX 75707  
Date  
07/13  
Trane has a policy of continuous product and product data improvement and it  
reserves the right to change design and specifications without notice.  

Hunter Fan 40035 Thermostat User Manual

Honeywell RTH2310 Thermostat User Manual

Honeywell TH8321 Thermostat User Manual

Honeywell T7047G Thermostat User Manual

White Rodgers 829A 845 Thermostat User Manual

Honeywell TH1000 Thermostat User Manual

Emerson 50M56 7433 Thermostat User Manual

Honeywell 8160 Thermostat User Manual

Honeywell T7984 B Thermostat User Manual

Honeywell T8400C Thermostat User Manual