White Rodgers 1A65W Thermostat User Manual

Home

href="
1A65/1A65W  
ELECTRIC-HEAT THERMOSTAT  
(Single Pole)  
WHITE-RODGERS  
INSTALLATION INSTRUCTIONS  
Operator: Save these instructions for future use!  
FAILURETOREADANDFOLLOWALLINSTRUCTIONSCAREFULLYBEFORE  
INSTALLING OR OPERATING THIS CONTROL COULD CAUSE PERSONAL  
INJURY AND/OR PROPERTY DAMAGE.  
DESCRIPTION  
The Type 1A65/1A65W Electric Heat Thermostat is de-  
signed for use on all types of electrical heating installa-  
tions such as cable heat, baseboards, wall insert heaters,  
etc. Its narrow operating differential and the ability of its  
fully exposed knob to sense both radiant heat and room  
air temperature make this control ideal for use on such  
installations.  
60  
70  
50  
80  
Dial Setting: Knob may be set anywhere between 40°  
and 85°F by simply turning knob so that indicator on knob  
points to the desired setting.  
PRECAUTIONS  
This control is a precision instrument, and should be All wiring must conform to local and national electrical  
handled carefully. Rough handling or distorting compo- codes and ordinances.  
nents could cause the control to malfunction. Take care  
WARNING  
not to push or damage the knob sensing element  
during installation.  
!
Do not use on circuits exceeding specified volt-  
ages. Higher voltages will damage control and  
could cause shock or fire hazard.  
CAUTION  
!
To prevent electrical shock and/or equipment  
Do not use on inductive loads. Inductive (motor)  
damage, disconnectelectricpower tosystem, at  
loadswilldamagecontrolandcouldcauseshock  
mainfuseorcircuitbreakerbox,untilinstallation  
or fire hazard.  
is complete.  
SPECIFICATIONS  
Temperature Range: 40° to 85°F  
Differential: 1°F  
Switch Rating: Non-Inductive  
22A (2500W) 120 VAC  
22A (5000W) 240 VAC  
18A (5000W) 277 VAC  
Switch Action: Open on rise  
Contact Structure: SPST  
INSTALLATION  
If the heating equipment manufacturer has made provi- 3. It should be mounted as far as possible from undesir-  
sions or recommendations for the location of this control,  
thenfollowthoseinstructions. Ifnot, thefollowingsugges-  
tions should be observed.  
able sources of heat and cold such as:  
a. Windows and doors  
b. Direct rays from sun  
1. The control should be mounted in the wall, approxi-  
mately five feet from the floor, as near as possible to  
the centre of the controlled area.  
c. Hot water or cold water pipes  
d. Adjoining outside walls  
2. It should be mounted on a partitioning wall, not on an  
outside wall.  
WHITE-RODGERS DIVISION  
EMERSON ELECTRIC CO.  
9797 REAVIS RD., ST. LOUIS, MO. 63123  
(314) 577-1300, Fax (314) 577-1517  
PART NO. 37-5427C  
Replaces 37-5427B  
9520  
Printed in U.S.A.  
9999 HWY. 48, MARKHAM, ONT. L3P 3J3  
(905) 475-4653, FAX (905) 475-4625  
href="
WIRING  
All wiring must conform to local and national electrical codes and ordinances.  
The thermostat may be mounted in any standard 2” x 3” 2. Push the lead wires into the outlet box and mount the  
electrical outlet box. For ease of installation use a deep  
type box.  
thermostat to the outlet box with screws provided.  
Take care not to push or damage the knob sens-  
ing element during installation.  
CAUTION  
!
3. Snap on the thermostat cover and turn knob to  
desired setting.  
USE WITH COPPER CONDUCTORS ONLY.  
1. Make electrical connection to thermostat leads with  
wire nuts or other local code approved devices. All  
connections must be tight.  
Thermostat  
Note: Do not  
push on this knob  
because calibration  
will be changed  
if knob is bent.  
Mounting Screw  
60  
70  
50  
80  
LINE  
LOAD  
Mounting Screw  
Cover  

Honeywell T841A Thermostat User Manual

Honeywell TB7200 Thermostat User Manual

Honeywell TH4110D Thermostat User Manual

Honeywell T834C2309 Thermostat User Manual

White Rodgers 1F79 111 Thermostat User Manual

Honeywell TRV15SHW Thermostat User Manual

Honeywell Y594G Thermostat User Manual

Honeywell 67 5146 JJ Thermostat User Manual

Honeywell CM900 Thermostat User Manual

Trane 570 Thermostat User Manual