Aprilaire 8620 Thermostat User Manual

Home

Modeꢀ 8620 Thermostat with

™

Event-based Air Cꢀeaninꢁ and

Humidity or Ventiꢀation Controꢀ

Safety &

Installation

Instructions

READ AND SAVE THESE INSTRUCTIONS

TAblE Of CONTENTS

INSTAllATION

SETUp & TESTINg

Installation location recommendations . . . . . .

Outdoor temperature sensor (included) . . . . . .

Remote temperature sensor (optional) . . . . . .

Thermostat mounting . . . . . . . . . . . . .

Power & reset options . . . . . . . . . . . .

Wiring terminal . . . . . . . . . . . . . . .

Equipment type selection switch (SW1) . . . . .

Installer setup menu . . . . . . . . . . . . .

Change system settings . . . . . . . . . . . .

HVAC installer system settings table . . . . . . 8-9

Indoor Air Quality system settings tables . . . . 10

Air cleaning sytem settings table . . . . . . 10

Humidifier system settings table . . . . . . .

Dehumidifier system settings table . . . . . .

WIRINg DIAgRAMS

Ventilation system settings table . . . . . . 11-12

Climate map for ASHRAE fresh air setup . . . . 12

Removal of Indoor Air Quality control buttons . . 13

Conventional heat/cool single transformer . . . .

Conventional heat/cool two transformer . . . . . 5

Heat pump single transformer . . . . . . . . .

Heat pump two transformer . . . . . . . . . .

Indoor Air Quality equipment – dehumidifier

Indoor Air Quality equipment – humidifier

System test menu . . . . . . . . . . . .

System test tables . . . . . . . . . . . .

13-14

15-16

REfERENCES

Indoor Air Quality equipment – ventilation . . . .

Quick reference to controls & display . . . . . .

Troubleshooting . . . . . . . . . . . . . .

Error codes . . . . . . . . . . . . . . . .

Thermostat features . . . . . . . . . . . . 19

Specifications . . . . . . . . . . . . . . . 20

INSTAllATION

INSTAllATION lOCATION RECOMMENDATIONS

Thermostat shouꢀd ꢂe mounted:

REMOTE TEMpERATURE SENSOR (OpTIONAl)

Do not mount thermostat:

A remote temperature sensor can be used if the thermostat has to be mounted in a concealed location A 8051 flush

mount or 8053 surface mount remote temperature sensor can be attached to the T1 and T2 terminals and mounted

in a recommended area The remote sensor must be enabled in the installer setup menu When the remote sensor is

installed it overrides the internal sensor

•

On an interior wall, in a frequently occupied space.

Approximately 5‘ above floor.

• Behind doors, in corners or other dead air spaces.

• In direct sunlight, near lighting fixtures, or other

appliances that give off heat

At least 18” from outside wall.

Remote temꢃerature sensor shouꢀd ꢂe mounted:

On an interior wall, in a frequently occupied space.

Do not mount remote sensor:

•

On an outside or unconditioned area wall.

Thermostat can be mounted to a vertical junction box.

•

• Behind doors, in corners or other dead air spaces.

In the flow of a supply register, in stairwells, or near

outside doors

• Approximately 5‘ above floor.

• At least 18” from outside wall.

• In direct sunlight, near lighting fixtures, or other

appliances that give off heat

•

On a wall with concealed pipes or ductwork.

•

On an outside or unconditioned area wall.

•

Using less than 300’ of wire.

OUTDOOR TEMpERATURE SENSOR (INClUDED)

• In the flow of a supply register, in stairwells, or near

outside doors

Outdoor temperature can be measured by attaching the included 8052 sensor to the S1 and S2 terminals The

outdoor sensor must be enabled in the installer setup menu

•

On a wall with concealed pipes or ductwork.

Near 120 VAC lines.

Heat ꢃumꢃ modeꢀs can use the outdoor temꢃerature to eꢄꢄectiveꢀy utiꢀize the heat ꢃumꢃ:

•

When the outdoor temperature is less than the Low Balance Point, the heat pump will be locked out and only

auxiliary heating will be used.

•

When the outdoor temperature is higher than the High Balance Point, the auxiliary heating will be locked out and

only the heat pump will be used to provide heating

Indoor Air Quaꢀity ꢄunctions can use the outdoor temꢃerature sensor to:

•

Control humidification setpoint based on outdoor temperature to prevent condensation

Lock out humidification for temperatures over 60°F or below -30°F.

Lock out ventilation based on high and/or low outdoor temperatures.

Display outdoor temperature on thermostat.

I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

Outdoor temꢃerature sensor shouꢀd ꢂe mounted:

THERMOSTAT MOUNTINg

•

On side of building out of direct sunlight (north side recommended).

Above snow line.

Remove the rear mounting plate from the thermostat

Pull wires through the opening on the back of the

thermostat

At least 3’ away from exhaust vents and condensing lines.

Using less than 300’ of wire.

Position and level the mounting plate of the thermostat

on wall and mark the hole locations with a pencil

Do not route wires along 120 VAC lines.

. Drill 1/4” holes and insert supplied anchors

drywall only)

(

. Place mounting plate over anchors, insert and tighten

screws

Seal wire entry holes to prevent drafts affecting

temperature readings

I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

INSTAllATION

pOWER & RESET OpTIONS

CONVENTIONAl HEAT/COOl WIRINg DIAgRAMS

SINglE TRANSfORMER (USE JUMpER WIRE)

The thermostat is dual power It can either be AC or

battery powered, or both (to provide backup power for

the clock). Batteries are optional if your thermostat was

wired to run on AC power when installed

TWO TRANSfORMERS (REMOVE JUMpER WIRE)

RESET

BUTTON

For heat pump systems the C terminal must be connected

to the common of the 24VAC transformer in order for the

system fault and emergency heat indicators to operate

The thermostat has a memory backup that saves the

thermostat settings in case of a power interruption The

system settings will be retained but the clock will reset

after 90 seconds with no battery or AC power

The reset button located under the battery cover can

be used to reset the thermostat to factory defaults The

system settings will also be reset to default

Note: The reset button is disabled when the thermostat

is removed from the wall for programming

I1 O/B Y Y2

RC R W2 W

S2 S1 T1 T2

I2 C I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

WIRINg TERMINAl

HEAT pUMp WIRINg DIAgRAMS

SINglE TRANSfORMER (USE JUMpER WIRE)

I1 & I2 – Indoor Air Quality control output

TWO TRANSfORMERS (REMOVE JUMpER WIRE)

C – Common (optional when powered by batteries)

O/b – Reversing valve

C I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

Y – 1st stage cooling / compressor

Y2 – 2nd stage cooling / compressor

g – Fan

RC – 24VAC supply cooling

R – 24VAC supply heating

Wire sꢃeciꢄications:

8-24 gauge thermostat wire

W2 – 2nd stage heat / auxiliary

W – 1st stage heat / auxiliary

l – System fault indicator (optional) (heat pump only)

S1 & S2 – outdoor temperature sensor (included)

T1 & T2 – remote temperature sensor (optional)

Instaꢀꢀation notes:

•

Ensure power at the HVAC equipment is off.

Loosen screw terminals, insert stripped wire and

Jumper between RC & R is used in single transformer systems

I2 C I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

C I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

re-tighten

(

see wiring diagrams).

•

Push the excess wire back into the opening and plug

the wall opening to prevent drafts

INSTAllATION

SETUp & TESTINg

INDOOR AIR QUAlITY EQUIpMENT WIRINg DIAgRAMS

EQUIpMENT TYpE SElECTION SWITCH (SW1)

This thermostat has the option of being used in heat

pump or heat/cool systems Switch SW1 located on the

back of the thermostat’s face is used to select this option.

This setting is displayed in the Installer System Settings

under Equipment Type

DEHUMIDIfIER WIRINg

HUMIDIfIER WIRINg

SW1

HEAT/COOL

HEAT PUMP

Note: Thermostat reboots within 10 seconds after switch

position is changed

INSTAllER SETUp MENU

HOW TO ENTER THE INSTAllER SETUp MENU AND SElECT EQUIpMENT TO SETUp:

In the Installer Setup, HVAC or Indoor Air Quality setup can be selected. If Indoor Air Quality setup is selected, the

user can then select to set up Air Cleaning, Humidification, Dehumidification or Ventilation.

I1 O/B Y Y2

RC R W2 W

S2 S1 T1 T2

I2 C I1 O/B Y Y2 G RC R W2 W L S2 S1 T1 T2

press [MODE] to set system to OFF.

press [MENU] to enter main menu

press

to adjust the option.

press [MENU] to exit.

VENTIlATION WIRINg

press and hoꢀd [SETUp] for seven seconds, [INSTAll

SETUp] appears

press [NEXT] to select option

If IAQ (Indoor Air Quality) was selected, press

press [INSTAll SETUp] to enter installer setup menu

to adjust the Outdoor Sensor setting or IAQ (Indoor

Air Quality) option

press [NEXT] to select Outdoor Sensor setting or IAQ

(

Indoor Air Quality) option

System Settings can now be changed

I1 O/B Y Y2

RC R W2 W

S2 S1 T1 T2

CHANgE SYSTEM SETTINgS

press [NEXT] or [bACK] to page through the settings

SETTING

DESCRIPTION

SETTING

NUMBER

Note: The I1/I2 output is a dry contact closure The humidifier wiring diagram assumes the control is powering a

solenoid valve The dehumidifier wiring diagram is for a normally open dry contact input The ventilation diagram

assumes the control is for a normally closed damper. Please see the individual humidifier, dehumidifier or ventilation

installation instructions for product specific wiring details

press

to adjust the setting.

SETTING

OPTIONS

press [DONE] to save and exit, or [CANCEl] to exit

without saving

The thermostat will discard changes and exit if nothing

is pressed within 60 seconds

To reset the installer settings to the default, reset

the thermostat by pressing the [RESET] button for 5

seconds

SETUp & TESTINg

HVAC INSTAllER SYSTEM SETTINgS TAblE

HVAC INSTAllER SYSTEM SETTINgS TAblE (CONTINUED)

The following table contains the system settings and their details Default settings are shown in ꢂoꢀd Some settings

are only available dependent upon the value of other settings

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

and settinꢁ ranꢁe

System settinꢁ

Descriꢃtion

9. Fourth Stage Differential 4th stage differential

1°f (0.5°C)

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

°F to 9°F (0.5°C to 4.5°C)

System settinꢁ

Descriꢃtion

and settinꢁ ranꢁe

0. Heat Blast

Enables the Heat Blast feature.

Disaꢂꢀe

Enable

0 Equipment Type

1 Reversing Valve

1 Control Setup

Equipment type set by SW1

Heat /Cooꢀ

Heat Pump

1. Blast Offset

2. Screen Lockout

Amount of heating when Heat Blast is initiated.

Screen lockout level (Override lockout by holding

3°f (2°C)

Selects O or B operation.

O – On in cooling

B – On in heating

°F to 5°F (2°C to 3°C)

Oꢄꢄ

Part

Full

Used to lockout heating or cooling outputs. (Only

available in Heat/Cool mode )

Heat and Cooꢀ

Heat Only

Cool Only

[

MENU] for 7 seconds.)

3. Partial Lockout Type

Select lockout type (Only available when screen

lockout is set to partial )

fan/Mode/Setꢃt

Fan/Setpoints

2. Number of Stages

3. Aux Heat Stages

4 Temperature Scale

Number of equipment stages.

One

Two

Setpoints Only

Number of auxiliary heat equipment stages.

Set the thermostat to Fahrenheit or Celsius mode.

One

Two

4. Max Temp Setpoint

Change In Lockout

Select temperature setpoint limits (Only available 3 deꢁrees

when screen lockout is set to partial )

0 to 20 degrees

fahrenheit

Celsius

1. Max Dehum Setpoint

Change In Lockout

Select dehumidification setpoint limits (Only

available when screen lockout is set to partial )

5 percent RH

0 to 15 Percent RH

5. Heat/Cool: Fan Control

in Heating

Heat Pump: Auxiliary

Equipment Type

Heat/Cool: Determines if the thermostat or

equipment controls the fan in heating

Heat Pump: Auxiliary Equipment type.

gas/Oiꢀ Heat (equipment controls fan)

Electric Heat (thermostat controls fan)

5 Stage Rate

Accumulation of equipment run time in equipment

staging determination

1 to 5 or “OFF” to ignore accumulated

= more rapid staging of equipment (comfort)

= slower staging of equipment (economy)

run time

6. Extended Fan – Heat

Extends fan operation after heat call ends.

Extends fan operation after cool call ends.

Field adjustment of internal temperature sensor.

Disaꢂꢀe

Enable (90 second extension)

7 Progressive Recovery

Enable or disable progressive recovery

Disable

Enaꢂꢀe

7. Extended Fan – Cool

Disaꢂꢀe

Enable (90 second extension)

8. Low Balance Point

Outdoor temperature low balance point (This

option is only displayed if the outdoor sensor is

enabled )

20°f (-6°C)

10°F to 50°F (-12°C to 9°C) or OFF to

8 Internal Temp Sensor

Offset

0° (no offset applied)

-4°F to +4°F (-2°C to +2°C)

ignore

9. High Balance Point

Outdoor temperature high balance point (This

option is only displayed if the outdoor sensor is

enabled )

65°f (18°C)

5 Internal RH Sensor Offset Field adjustment of internal RH sensor.

0 (no offset applied)

40°F to 85°F(3°C to 18°C) or OFF to

5% to +5%

ignore

9 Auto Changeover

6 Deadband

Enable or disable auto changeover mode

Auto Changeover mode deadband

Disaꢂꢀe

Enable

30. Program Format

Select weekly program format

7-Day (Mon, Tue, Wed, Thu, Fri, Sat, Sun)

5/1/1 (weekdays, Saturday and Sunday)

/2 Weekdays (weekdays and weekends)

3°f (2°C)

Non-Prog

°F to 9°F (1°C to 5°C)

2 Events Per Day

Number of program events per day.

four

Two

0 Remote Sensor

1 Outdoor Sensor

Select if remote sensor is attached

Select if outdoor sensor is attached or not

Yes

3 Reset Service Reminders Clears the Change Air Filter and HVAC and

Dehumidifier Service reminders if they are active

and resets the start date to the current date

Clears the Change Water Panel reminder if it is

active. If the reminder is set to timed, the clock

will be reset

Yes

2. Compressor Min Off Time Minimum off time for compressor protection.

5 minutes

to 5 minutes

3. Heating Min Off Time

4. Equipment Min On Time

5 Auto Changeover Time

6. First Stage Differential

Minimum off time for heating.

2 minutes

to 5 minutes

37 HVAC Service Reminder

38. Constant Backlight

39. Backlight Intensity

The period for displaying the “HVAC Service

Reminder” message.

Oꢄꢄ

1 to 12 months or “Off” to disable

Minimum on time for heating and cooling.

2 minutes

to 5 minutes

Enable constant, low intensity backlight when

Disaꢂꢀe

Enable

4VAC is present

Minimum time between heating and cooling calls. 4 minutes

to 5 minutes

Backlight intensity as a percentage of full on.

100 Percent

to 100 Percent

1st stage differential

1°f (0.5°C)

°F to 9°F (0.5°C to 4.5°C)

40 Auto Daylight Savings

Enable or disable auto daylight savings

Off

March (second Sunday in March to the

first Sunday in November)

April (first Sunday in April to the last

Sunday in October)

7 Second Stage Differential 2nd stage differential

8 Third Stage Differential 3rd stage differential

1°f (0.5°C)

°F to 9°F (0.5°C to 4.5°C)

1°f (0.5°C)

°F to 9°F (0.5°C to 4.5°C)

SETUp & TESTINg

INDOOR AIR QUAlITY SYSTEM SETTINgS TAblES

Dehumidiꢄier System Settinꢁs Taꢂꢀe

Note: Dehumidifier control can only be set to whole home if ventilation and humidification are not installed

The following tables contain the Indoor Air Quality system settings and their details Default settings are shown in

ꢂ

oꢀd Some settings are only present dependent upon the value of other settings

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

System settinꢁ

Descriꢃtion

and settinꢁ ranꢁe

The use of the included outdoor temperature sensor (recommended) enables additional Indoor Air Quality functionality

If the outdoor temperature sensor was not enabled in the HVAC system settings, HVAC system setting 11, outdoor

sensor, will be presented prior to entering the Indoor Air Quality system settings.

Dehumidifier Control

Selects method of dehumidification.(If set to none, no

other dehumidifier settings will be available )

None (no dehumidification installed)

Whole Home

Air Conditioner

Please refer to the Model 8620 Owner’s Manual for further information about thermostat features.

Air Cꢀeaninꢁ System Settinꢁs Taꢂꢀe

Humidity Setpoint Deadband Select the minimum difference between the humidifier 10 Percent RH

and dehumidifier setpoints (Only available if

humidifier mode is set to manual and dehumidifier

control is set to air conditioner Available in both

set-ups )

10 to 20 Percent RH

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

and settinꢁ ranꢁe

System settinꢁ

Descriꢃtion

Lockout Dehumidifier During Selects if dehumidification is disabled during a cooling No

Air Cleaner Installed

Selects if an air cleaner is installed. (If set to no, no other

air cleaning settings will be available )

Yes

Cooling

call (Only available if dehumidifier control is set to

whole home )

Yes

Change Air Filter Reminder The period for displaying the “Change Air Filter” message.

Oꢄꢄ

Dehumidifier Forces Fan

Select if dehumidification can turn on the fan (Only

to 12 months or “Off” to disable

available if dehumidifier control is set to whole home ) Yes

Dehumidifier Service

Reminder

The period for displaying the “Dehum Service

Reminder” message. (Only available if dehumidifier

control is set to whole home )

Oꢄꢄ

Humidiꢄier System Settinꢁs Taꢂꢀe

1 to 12 months or “Off” to disable

Note: A humidifier can only be installed if ventilation is not installed and dehumidifier control is not set to whole home

Dehumidifier Overcooling

Selects the amount of overcooling that can occur

for dehumidification (Only available if dehumidifier

control is set to air conditioner )

3°f (1.5°C)

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

Limit

1°F to 3°F (0.5°C to 1.5°C)

System settinꢁ

Descriꢃtion

and settinꢁ ranꢁe

Humidifier Installed

Selects if a humidifier is installed. (If set to no, no other

humidifier settings will be available )

Yes

Auto

Manual

Dehumidify in Vacation

Mode

Selects if dehumidification with the air conditioner is

done in Vacation Mode. (Only available if dehumidifier Yes

Humidifier Mode

Selects auto or manual mode Auto mode controls humidity

based on the humidity setting and outdoor temperature

Manual mode controls humidity based on the %RH setpoint.

control is set to air conditioner

Vacation Dehumidifier Low

Temp Limit

Sets the lowest temperature the air conditioner will cool 75°f (24°C)

to meet RH setpoint in Vacation Mode. (Only available if 70°F to 85°F (21°C to 29°C)

dehumidifier control is set to air conditioner )

(Auto mode is only available if outdoor sensor is set to yes )

Humidity Setpoint

Deadband

Select the minimum difference between the humidifier

and dehumidifier setpoints (Only available if humidifier

mode is set to manual and dehumidifier control is set to air

conditioner Available in both set-ups )

10 Percent RH

10 to 20 Percent RH

Ventiꢀation System Settinꢁs Taꢂꢀe

Note: Ventilation can only be installed if humidification is not installed and dehumidifier control is not set to whole home

Humidifier Operation

Selects when humidification is allowed to occur relative to

heating and fan operation

Heat Onꢀy

Heat or Fan

Forces Fan

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

System settinꢁ

Descriꢃtion

and settinꢁ ranꢁe

Change Water Panel

Reminder

Selects the when the “Change Water Panel” message is

Oꢄꢄ

Fresh Air Vent Installed Selects if ventilation is installed

displayed

1 Per Season

(

If set to no, no other ventilation settings will be available.)

Yes

Per Season

00 Hours

Fresh Air Forces Fan

Fresh Air Setup

Selects if ventilation forces the fan on

Yes

Reminder Month (Change

Change Water Panel Reminder set to 1 per Season:

Octoꢂer

Selects if ventilation is configured through the ASHRAE setup

or Timed. If ASHRAE setup is selected, the hourly ventilation

time will be calculated using the ASHRAE recommendations

If Timed set-up is selected, the hourly ventilation time will be

determined based on the Fresh Air Time value.

Timed

ASHRAE

Water Panel Reminder set Determines the month the “Change Water Panel” message November

to 1 per Season)

is displayed

December

January

February

March

April

First Reminder Month

Change Water Panel Reminder set to 2 per Season:

Determines the first month the “Change Water Panel”

message is displayed

(

Change Water Panel

Fresh Air Time

Selects how many minutes per hour that ventilation will be

active (Only available if fresh air setup is set to timed )

30 MIN/HR

0 to 60 MIN/HR

Reminder set to 2 per

Season)

May

High Limit Outdoor

Temp

Selects if ventilation is disabled if the outdoor temperature

June

exceeds the outdoor high limit. (Only available if fresh air setup Yes

July

is set to timed and an outdoor temperature sensor is installed )

August

September

Outdoor High Limit

Sets the high temperature limit for ventilation (Only available if 100°f (38°C)

high limit outdoor temp set to yes )

Second Reminder Start

Month

Determines the second month the “Change Water Panel”

message is displayed (Only available when Change Water

Panel Reminder set to 2 per Season )

October

November

December

January

February

March

90°F to 100°F (32°C to 38°C)

Low Limit Outdoor Temp Selects if ventilation is disabled if the outdoor temperature

exceeds the outdoor low limit. (Only available if fresh air setup Yes

is set to timed and an outdoor temperature sensor is installed )

Outdoor Low Limit

High Limit Indoor RH

Indoor RH Limit

Sets the low temperature limit for ventilation (Only available if 10°f (-11°C)

low limit outdoor temp set to yes )

-10°F to 30°F (-23°C to -1°C)

April

May

Selects if ventilation is disabled if the indoor RH exceeds the

indoor RH limit (Only available if fresh air setup is set to timed ) Yes

June

July

Sets the high indoor RH limit for ventilation (Only available if

high limit indoor RH is set to yes )

60%

50% to 70%

August

September

SETUp & TESTINg

Ventiꢀation System Settinꢁs Taꢂꢀe (continued)

REMOVAl Of INDOOR AIR QUAlITY CONTROl bUTTONS

factory deꢄauꢀt settinꢁ (ꢂoꢀd)

and settinꢁ ranꢁe

If any of the Indoor Air Quality control features are not installed, the corresponding button can be removed using the

following procedure:

System settinꢁ

Descriꢃtion

Number of Bedrooms

Selects the number of bedrooms to be used for the ASHRAE

3 bedrooms

calculation (Only available if fresh air setup is set to ASHRAE ) 1 to 6 Bedrooms

Steꢃ 1: Verify the specific Indoor Air

Quality control feature is not

installed in the installer set-up

Number of Occupants

Home Size

Selects the number of occupants to be used for the ASHRAE

4 Occuꢃants

calculation (Only available if fresh air setup is set to ASHRAE ) 1 to 10 Occupants

INDOOR

(

see pages 10-12)

AIR QUALITY

CONTROL

Selects the home size to be used for the ASHRAE calculation

Only available if fresh air setup is set to ASHRAE )

2500 SQ fT

1000 to 5000 SQ FT

(

Steꢃ 2: From the home screen (see

page 17), ꢃress and hoꢀd the

IAQ button for 7 seconds

BUTTONS

Fresh Air CFM

Select Climate

Selects the ventilation CFM to be used for the ASHRAE

60 CfM

calculation (Only available if fresh air setup is set to ASHRAE ) 30 to 200 CFM

Selects the climate to be used for the ASHRAE calculation

Normaꢀ

Very Hot/Humid

Very Cold

Steꢃ 3: The message center will

display REMOVE BUTTON and

the options of NO and YES

(

Only available if fresh air setup is set to ASHRAE ) To

determine what region you are in, refer to the map below.

ASHRAE Cycle Time

Displays the Fresh Air Time calculated by the ASHRAE

standard (Only displayed if fresh air setup is set to ASHRAE )

Minutes/Hour

(

NO will be flashing).

Steꢃ 4: press

or to select YES

Steꢃ 5: press [DONE]

Steꢃ 6: The button is now removed

Note: Once the button is removed it can be brought back by installing the corresponding Indoor Air Quality feature

Note: In ASHRAE set-up temperature and humidity limits are disabled

Note: Refer to manuals for humidifier, dehumidifier, air cleaner and ventilation products for recommended

installation and operation

(

see pages 10-12)

ClIMATE MAp fOR ASHRAE fRESH AIR SETUp

SYSTEM TEST MENU

The system test menu is used to test a system after installation The outputs of the thermostat can be manually

activated to test their function The instructions below show how to enter the test mode and turn outputs on and off

HOW TO ENTER THE SYSTEM TEST MENU:

SYSTEM TEST STEpS

VERY COlD

press [MODE] to set system to off

Heating equipment test

Cooling equipment test

press and hoꢀd [fAN] and [MODE] for three seconds

to enter system test mode

Fan equipment test

Humidification equipment test

Dehumidification equipment test

Ventilation equipment test

The first screen of the installer test displays the

equipment configuration

press [NEXT] to enter the first installation test or

[

CANCEl] to exit.

HUMIDITY

TEMPERATURE

VERY HOT/HUMID

OUTDOOR

TEMPERATURE

EQUIPMENT

CONFIGURATION

SETUp & TESTINg

SYSTEM TEST MENU (CONTINUED)

SYSTEM TEST TAblES

Each equipment test will begin with the selection of turning on the output or stage as shown below

Heat / Cooꢀ Heatinꢁ Equiꢃment Test

press

to change the selection

Heat Tyꢃe

press [NEXT] to accept the selection and proceed to the next step.

Gas

1st Stage Test

2nd Stage Test

If YES is selected, the thermostat will test the corresponding output. If NO is selected, the thermostat will proceed

to the next step.

Electric

1st Stage Test

2nd Stage Test

HUMIDITY

Heat pumꢃ Heatinꢁ Equiꢃment Test (Eꢀectric Heat)

TEMPERATURE

O/b set to

Comꢃressor

Staꢁes

Aux

OUTDOOR

TEMPERATURE

Staꢁes

EQUIPMENT TEST

SELECTION

1st Stage Test

2nd Stage Test

TEST TO BE RUN

1st Stage Test

2nd Stage Test

3rd Stage Test

1st Stage Test

2nd Stage Test

3rd Stage Test

While the equipment test is active the corresponding test information will be shown

1st Stage Test

2nd Stage Test

3rd Stage Test

4th Stage Test

press [NEXT] to accept the selection and proceed to the next test selection.

Note: System Variable 31, O/B operation selects O or B.

HUMIDITY

TEMPERATURE

Heat pumꢃ Heatinꢁ Equiꢃment Test (gas Heat)

OUTDOOR

TEMPERATURE

O/b set to

Comꢃressor

Staꢁes

Aux

Staꢁes

1st Stage Test

2nd Stage Test

EQUIPMENT TEST

SELECTION

OUTPUT STATUS

TEST THAT

IS ACTIVE

1st Stage Test

2nd Stage Test

3rd Stage Test

1st Stage Test

2nd Stage Test

3rd Stage Test

1st Stage Test

2nd Stage Test

3rd Stage Test

4th Stage Test

Note: System Variable 31, O/B operation selects O or B.

SETUp & TESTINg

QUICK REfERENCE TO CONTROlS & DISplAY

SYSTEM TEST TAblES (CONTINUED)

HOME SCREEN

ROOM TEMPERATURE

CURRENT DAY OUTDOOR TEMPERATURE ROOM RELATIVE HUMIDITY

TEMPERATURE SETTING

Heat / Cooꢀ Cooꢀinꢁ Equiꢃment Test

AIR CLEANING BUTTON

FAN MODE

BUTTON

™

(

ENTERS EVENT-BASED AIR

st Stage Test

CLEANING CONTROL SCREEN)

nd Stage Test

FAN MODE

SETTING

HUMIDITY CONTROL BUTTON

(ENTERS HUMIDITY CONTROL

SCREEN)

Heat pumꢃ Cooꢀinꢁ Equiꢃment Test

SYSTEM MODE

BUTTON

FRESH AIR BUTTON (ENTERS

VENTILATION CONTROL SCREEN)

O/b set to

SYSTEM MODE

SETTING

TEMPERATURE ADJUSTMENT

INDICATORS SHOW THROUGH HOUSING

HEAT pUMp ONlY

EMERGENCY HEAT OR

AUXILIARY HEAT (RED)

st Stage Test

nd Stage Test

EQUIPMENT

STATUS

Note: System Variable 31, O/B operation selects O or B.

SYSTEM FAULT (YELLOW)

MESSAGE

CENTER

fan Equiꢃment Test

(

SCROLLING TEXT)

HOLD BUTTON

(

SETS OR CLEARS HOLD)

LOW BATTERY

INDICATOR

CURRENT TIME & DATE MAIN MENU BUTTON

HEAT BLAST BUTTON

Humidiꢄication Equiꢃment Test

I1/I2

NOTE: BACKLIGHT IS ACTIVATED WITH FIRST BUTTON PRESS AND AUTOMATICALLY TURNS OFF.

Dehumidiꢄication Equiꢃment Test

Ventiꢀation Equiꢃment Test

MAIN MENU

I1/I2

SET VACATION HOLD

HOLD–TO TIME AND DATE)

SET SCHEDULE

BUTTON

(

SET CURRENT

TIME AND DATE

CLEAN SCREEN

DONE BUTTON

(

LOCKOUT TOUCH

(

EXIT MENU)

SCREEN FOR 30

SECONDS)

USER SYSTEM SETTINGS

TROUblESHOOTINg

ERROR CODES

If the thermostat enters an error mode, all outputs are turned off. The thermostat attempts to recover every 10 minutes.

If the error does not clear, use the reset button. This will return all settings back to factory default.

DISplAY IS blANK

HEAT pUMp ISSUES COOl AIR IN HEAT MODE,

OR WARM AIR IN COOl MODE

•

Check circuit breaker and reset if necessary.

•

Check System Setting 31 (O/B Operation) to make

sure the reversing valve operation matches the heat

pump

Error code

Messaꢁe

Error Descriꢃtion

Make sure power switch at heating & cooling

system is on

Open temperature sensor circuit

Shorted temperature sensor circuit

Error in permanent memory

“SENSOR ERROR”

“EEPROM ERROR”

•

Make sure furnace door is closed securely.

If thermostat is battery powered, make sure fresh AA

alkaline batteries are correctly installed

HEAT/COOl bOTH ON AT SAME TIME

•

Check SW1 (Equipment Type), to make sure it is set

to match the installed heating/cooling equipment

TEMpERATURE SETTINgS DO NOT CHANgE

(

see page 8)

Make sure heating and cooling temperatures are set to

acceptable ranges:

THERMOSTAT fEATURES

Check to make sure heating and cooling wires are

not shorted together

•

Indoor air quality control.

• Dual power option (24VAC or battery).

•

Heat: 40° to 90°F (4° to 32°C).

Cool: 50° to 99°F (10° to 37°C).

–

Humidification automatic or manual control

•

Front battery door access for fast, easy replacement.

HEATINg EQUIpMENT IS RUNNINg IN

COOl MODE

– Dehumidification

™

– Event-Based air cleaning

• Displays room temperature, room humidity,

temperature setting, and outdoor temperature.

HEATINg SYSTEM DOES NOT RESpOND

– Ventilation with temperature and humidity limits

•

Check SW1 (Equipment Type), to make sure it is set

to match the installed heating/cooling equipment

(see page 8)

(

“HEATINg” AppEARS ON SCREEN)

•

Temperature control.

• Air filter, humidifier, dehumidifier, and HVAC service

reminders

•

Check for 24VAC at the equipment on the secondary

side of the transformer between power and

common. If voltage is not present, check the heating

equipment to find the cause of the problem

™

Heat Blast raises the room temperature 3°F to 5°F.

• Programmable fan control with fan circulation mode.

Large touch screen with adjustable backlight –

constant backlight option available

“

HEATINg” IS NOT DISplAYED

• Easy to use temperature control can override program

schedule at any time

Check for 24VAC between the heat terminal (W)

and the transformer common. If 24VAC is present,

the thermostat is functional Check the heating

equipment to find the cause of the problem

• Check Installer System Setting number 01

•

Message center provides feedback and instructions.

(Control Setup) is set correctly

•

Progressive recovery ensures proper temperature at

7 day programmability or separately programmable

weekday/weekend schedules

the start of a program event

•

Change the System Mode to Heat, and set

the temperature level above the current room

temperature

• Built in compressor protection prevents damage to

your equipment

•

Thermostat can be removed from the wall for easy

programming (batteries must be installed)

Check for loose or broken wires between the

thermostat and the heating equipment

•

System test mode.

“

COOlINg” IS NOT DISplAYED

COOlINg SYSTEM DOES NOT RESpOND

•

Check Installer System Setting number 01

(

“COOlINg” AppEARS ON SCREEN)

(

Control Setup) is set correctly

•

Check for 24VAC at the equipment on the secondary

side of the transformer between power and

common. If voltage is not present, check the cooling

equipment to find the cause of the problem

Change the System Mode to Cool, and set

the temperature level below the current room

temperature

Check for 24VAC between the cooling terminal (Y)

and the transformer common. If 24VAC is present,

the thermostat is functional Check the cooling

system to find the cause of the problem

HUMIDIfIER DOES NOT OpERATE IN

AUTO MODE

•

Check Installer System Setting number 11 (Outdoor

Sensor) is set to yes

Check for loose or broken wires between the

thermostat and the cooling equipment

Verify that the outdoor sensor is functioning

correctly If the sensor is functioning correctly the

outdoor temperature will display in the outdoor

temperature location (see Home Screen on page 17

for the location)

fAN DOES NOT TURN ON IN A CAll fOR HEAT

•

Check System Setting 05 (Fan Control), to make sure

the fan control is properly set to match the type of

system (see page 8)

SpECIfICATIONS

Environment

Operating: 32° to 120°F (0° to 48.9°C)

Shipping: -30° to 150°F (-34.4° to 65.5°C)

Temperature

Relative humidity

Operating: 5% to 90% R H (non-condensing)

Eꢀectricaꢀ

Operating voltage

Current

24VAC (18 – 30VAC)

Maximum: 2.5A (total), 1.0A (single output)

Maximum surge current: 5A

Dual power Can be battery or 24VAC powered

Power supply

When both the sources are available, battery will be used as

back up power

Battery power: AA size alkaline battery x 2

Battery life: Approximately 1 year

Battery power

Thermaꢀ

Outdoor & Remote temperature sensor

Room temperature measurement

Outdoor temperature measurement

Maximum distance: 300 feet

Display range: 32° to 99°F (0° to 40°C)

Display range: -20° to 130°F (-30° to 55°C)

Heat: 40° to 90°F (4° to 32°C)

Cool: 50° to 99°F (10° to 37°C)

Setpoint temperature range

Setpoint humidity range

Humidification: 10% to 50% R H

Dehumidification: 40% to 90% R H

P.O. Box 1467 • Madison, WI 53701-1467 • Phone: 800/334-6011 • Fax: 608/257-4357

www.aꢃriꢀaireꢃartners.com

0009857 4 12

U.S. Patent Number 8,146,376 (and other patents pending)

B2205748A

Carrier TCSNAC01 Thermostat User Manual

Honeywell R7851C Thermostat User Manual

Honeywell CT87J Thermostat User Manual

Aprilaire 8336 Thermostat User Manual

Honeywell 95 7769 01 Thermostat User Manual

Honeywell T8501D Thermostat User Manual

Honeywell 4000 Thermostat User Manual

Honeywell T7300 Thermostat User Manual

Honeywell MS3000 Thermostat User Manual

Emerson 850 Thermostat User Manual