Lux Products WTR064 Thermostat User Manual

52079

Part No. WTR064

Accurately Displays

Current Outdoor Temperature and

Enables Dual Fuel* and

Automatic Humidity* Capability

on the LUXPRO^®Thermostat

* SELECTED MODELS ONLY

Before you begin, make sure that the time on the LUXPRO^®thermostat is set.

If not, set the time before starting the installation.

INSTALLATION INSTRUCTIONS

1. Install the included 2 AA batteries by removing the 4 screws located at the back of the

transmitter. The LED on the transmitter will flash every 6 seconds. Do not close the

battery compartment yet.

2. Remove the top cover of the thermostat and plug the receiver into the white connector

located to the bottom left under the touch screen. (A)

3. Place the antenna wire into the 4th vent as shown (B).

Clip the receiver into the 1st vent (C).

4. Press the “RESET” button (D) on the receiver module for 10 seconds to activate the

transmitter and receiver. The outdoor temperature will appear on your thermostat within

5 minutes. Make sure that the dot to the left of the outdoor temperature (E) flashes

approximately every 15 seconds. If after 5 minutes the outdoor temperature is not

displayed on the thermostat or if the dot to the left of the outdoor temperature (E) is not

flashing, unplug the receiver module from the thermostat, remove batteries from the

transmitter and start the installation procedure again.

5. Close the battery compartment and position the transmitter in a permanent location that

is sheltered from the elements. After placing the transmitter in a permanent location,

ensure that the dot to the left of the temperature (E) flashes approximately every 15

seconds. If the dot to the left of the temperature (E) is not flashing, change the

transmitter location.

6. Use the chart below as a reference for the recommended humidity settings.

WARNING: Adjusting the humidity control higher than the recommended setting may cause

condensation, resulting in possible damage to the home.

HUMIDITY SETTING RECOMMENDATIONS

At Outside Temperatures Of:

Humidity Setting:

-20°F (-29°C)

-10°F (-23°C)

0°F (-17°C)

+10°F (-12°C)

+20°F (-6°C)

15 %

20 %

25 %

30 %

35 %

40 %

Over +32°F (0°C)

OBTAINING WARRANTY SERVICE:

Customer must contact and return product to a local LUX Products Corporation product

dealer or installer within the applicable warranty period to obtain warranty service. Dated

proof of original purchase will be required.

HARDWARE:

LUX Products Corporation warrants the original end user (“Customer”) that new LUXPRO^®

branded products will be free from defects in workmanship and materials, under normal

use, for three (3) years from the original purchase date.

SOFTWARE:

LUX Products Corporation warrants to Customer that the LUXPRO^®thermostat software will

perform in substantial conformance to its program specifications a period of three (3) years

from the date of the original purchase.

EXCLUSIONS:

This warranty excludes (1) physical damage to the surface of the product, including cracks

or scratches on the touch-screen or outside casing; (2) damage caused by misuse, neglect,

improper installation, unauthorized attempts to open, repair, or modify the product, or any

other cause beyond the range of intended use; damage caused by accident, fire, power

changes, other hazard, or Acts of God; (4) use of the product with any device if such device

causes the problem.

EXCLUSIVE REMEDIES:

Should a covered defect occur during the warranty period and Customer notifies LUX

Products Corporation, Customer’s sole and exclusive remedy will be, at LUX Products

Corporation’s sole option and expense, to repair or replace the product. Replacement

products or parts may be new or reconditioned or a comparable version of the defective

item. LUX Products Corporation warrants any replaced product or part for a period of ninety

(90) days from shipment, or through the end the original warranty, whichever is longer.

WARRANTY EXCLUSIVE:

THE FORGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND IN LIEU ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES MERCHANTABILITY,

FITNESS FOR A PARTICULAR PURPOSE, CORRESPONDENCE WITH DESCRIPTION, AND

NON INFRINGEMENT, ALL OF WHICH ARE EXPRESSLY DISCLAIMED BY LUX PRODUCTS

CORPORATION AND ITS SUPPLIERS.

DISCLAIMER:

NEITHER LUX PRODUCTS CORPORATION NOR ITS SUPPLIERS SHALL BE LIABLE FOR

INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY

KIND, OR FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE OR USE

OF THIS PRODUCT, WHETHER BASED IN CONTRACT, TORT (INCLUDING NEGLIGENCE) OR

ANY OTHER THEORY, EVEN IF LUX PRODUCTS CORPORATION HAS BEEN ADVISED OF THE

POSSIBILITY OF SUCH DAMAGES. LUX PRODUCTS CORPORATION’S ENTIRE LIABILITY

SHALL BE LIMITED TO REPLACEMENT OR REPAIR OF THE PRODUCT.

FCC STATEMENT: THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION

IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE

HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE

RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE

CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS

COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. THIS DEVICE HAS

BEEN DESIGNED TO OPERATE WITH THE INCLUDED ANTENNA, AND HAVING A MAXIMUM

GAIN OF 0 dBd. ANTENNAS NOT INCLUDED OR HAVING A GAIN GREATER THAN 0 dBd ARE

STRICTLY PROHIBITED FOR USE WITH THIS DEVICE. THE REQUIRED ANTENNA

IMPEDANCE IS 52 OHMS.

U.S. Patent: 6,902,117