Aube CT230 120GB Thermostat User Manual

Home

href="
Installation Instructions  
MASTER THERMOSTATS  
TH113-A/F/AF (12VDC)  
TH114-A/F/AF (12VDC)  
TH115-A/F/AF (12VDC)  
TH116-A/F/AF (12VDC)  
SLAVE UNITS  
CT230-120GA  
CT230-120GB  
CT230-240GA  
CT230-240GB  
3
.2 Slave Units - Installation and Wiring  
1
. Introduction  
The slave units can operate on different voltages (e.g. 5 units @ 120 V and 5 @ 240 V).  
This master and slave unit system is specially  
designed for large floor heating applications  
exceeding 15 A.  
Required parts: CT230-120GA, -120GB, -240GA or -240GB  
Installation: On an electrical box  
The master thermostat controls a single or  
multiple floor heating zones driven by slave units.  
The master thermostat can control up to 10 slave  
units.  
Each slave unit drives its own zone and is  
equipped with a GFCI test button and warning  
light as well as an On/Standby switch to facilitate  
maintenance on specific zones of the floor  
installation.  
Location: Installation near the master  
thermostat is not required (i.e. can be  
installed in a utility room).  
Wiring: The power bases are joined  
through a daisy chain connection.  
n Connect the 120 V or 240 V power  
base wires to the power (line) and to  
the load (floor) using solderless con-  
nectors for copper wires, and secure  
the base to the electrical box.  
2
. Operation  
o Affix the wiring sticker (in the CT230  
Master Thermostat  
box) to the base.  
The master unit controls the temperature and  
sends a signal to slave units when heating is  
required. The floor sensor is connected to the  
master unit. The master unit is powered by the  
slave units.  
p Connect the slave power bases  
together as per FIGURE 1.  
q Once installation and wiring is com-  
plete, mount the CT230 interface:  
a) Align the bracket tabs of the  
CT230 with the holes located on  
Slave Unit  
The slave unit receives the signal sent by the  
master unit and activates its load.  
top of the power base.  
b) Secure the CT230 interface using the screw (captive).  
NOTE: There must be a minimum of one slave  
unit ON to power the master unit.  
3
. Installation  
Turn off power to the heating system at the  
main power panel to avoid electrical shock.  
Installation should be carried out by an  
electrician.  
3.1 Wiring Guidelines  
The wire distance between the master thermo-  
stat and slave unit should not exceed 500 ft.  
(
150 m).  
The floor sensor cable should not exceed  
00 ft. (60 m).  
A 3-wire 20 AWG cable is recommended.  
r Switch all slave power bases to STANDBY by sliding the protective door upwards  
and positioning the switch to STANDBY.  
2
Install and connect the master unit (see 3.3).  
FIGURE 1  
Connections  
4
00-230-000-D  
2/7/07  
1/2  
href="
3
.3 Master Thermostat - Installation and Wiring  
Technical Specifications  
WARNING: Make sure all slave units are in STANDBY mode.  
Temperature:  
-
-
Operation: 32°F to 122°F (0°C to 50°C)  
Storage: -4°F to 122°F (-20°C to 50°C)  
Required parts:  
TH113-A/F/AF (12VDC),  
TH114-A/F/AF (12VDC),  
TH115-A/F/AF (12VDC) or  
TH116-A/F/AF (12VDC)  
TH113/TH114/TH115/TH116 (A/F/AF-12VDC)  
Power supply  
12 V from remote unit  
Location: anywhere easily accessible to users.  
Maximum  
slave units  
up to 10 slave units per  
master thermostat  
Temperature control: AF (ambient with floor limit) / A (ambient)  
Wire gauge  
20 AWG  
Install the master thermostat in the controlled area.  
Size (H • W • D)  
BASE  
4.63 x 2.7 x 0.61 in.  
(117.5 x 68.3 x 15 mm)  
Choose a location about 5 ft. above the floor in an area where the tempera-  
ture is stable.  
Avoid locations where there are air drafts (top of staircase, air outlet), dead air  
spots (behind a door), direct sunlight or concealed chimneys or stove pipes.  
NOTE: Refer to the TH11x user guide for technical  
specifications.  
Temperature control: F (floor)  
Can be installed anywhere.  
CT230-120GA/120GB/240GA/240GB  
Supply  
-
PB112-120  
1800 W @ 120 VAC  
0 Hz, 15 A resistive  
3600 W @ 240 VAC  
0 Hz, 15 A resistive  
s Wire the 12 VDC base to the nearest slave unit.  
6
The floor sensor must be installed in an area where average temperature can be  
read. The cable must follow the wall down to the floor and must not cross any  
heater wires or be directly on or adjacent to a heating wire.  
For maximum performance, the sensor probe should be centered between the  
wires in the mat (max. 80°C).  
-
PB112-240  
6
GFCI  
GA=5 mA / GB=30 mA  
c CSA us  
Certification  
Size (H • W • D)  
BASE  
4.63 x 2.7 x 1.45 in.  
(117.5 x 68.3 x 37 mm)  
t Push the excess wire into the wall, secure the base using the provided screws  
and wall anchors, and install the TH11x thermostat onto the base.  
Size (H • W • D)  
INTERFACE  
4.67 x 2.74 x 0.67 in.  
(118.6 x 69.6 x 17 mm)  
u Once the thermostat is installed, return power to heating system and switch all  
slave units and the master thermostat to ON.  
Warranty  
Aube warrants this product, excluding battery, to be free  
from defects in the workmanship or materials, under nor-  
mal use and service, for a period of three (3) years from the  
date of purchase by the consumer. If at any time during the  
warranty period the product is determined to be defective  
or malfunctions, Aube shall repair or replace it (at Aube's  
option).  
If the product is defective,  
(
i)  
return it, with a bill of sale or other dated proof of pur-  
chase, to the place from which you purchased it, or  
contact Aube. Aube will make the determination  
whether the product should be returned, or whether  
a replacement product can be sent to you.  
(ii)  
3
.4 Slave Units - GFCI Test  
This warranty does not cover removal or reinstallation  
costs. This warranty shall not apply if it is shown by Aube  
that the defect or malfunction was caused by damage  
which occurred while the product was in the possession of  
a consumer.  
We recommend you test the GFCI immediately after installing the thermostat, and  
once a month thereafter to ensure it is operating properly.  
If the test warning light comes ON during normal operation, cut power to heating  
system from the main power panel and verify the installation.  
Aube's sole responsibility shall be to repair or replace the  
product within the terms stated above. AUBE SHALL NOT  
BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND,  
INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL  
DAMAGES RESULTING, DIRECTLY OR INDIRECTLY,  
FROM ANY BREACH OF ANY WARRANTY, EXPRESS  
OR IMPLIED, OR ANY OTHER FAILURE OF THIS PROD-  
UCT. Some provinces, states or regions do not allow the  
exclusion or limitation of incidental or consequential dam-  
ages, so this limitation may not apply to you.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY  
AUBE MAKES ON THIS PRODUCT. THE DURATION OF  
ANY IMPLIED WARRANTIES, INCLUDING THE WAR-  
RANTIES OF MERCHANTABILITY AND FITNESS FOR A  
PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE  
THREE-YEAR DURATION OF THIS WARRANTY. Some  
provinces, states or regions do not allow limitations on how  
long an implied warranty lasts, so the above limitation may  
not apply to you.  
n Slide the protective door upwards and make sure the switch is ON.  
o Press TEST.  
The test is successful if the TEST warning light is ON and power is cut off.  
This warranty gives you specific legal rights, and you may  
have other rights which vary from province, state or region  
to another.  
If the test fails (first installation test):  
a. Verify installation  
b. Check the load wires  
c. Once you've identified the problem, run the GFCI test again  
Service  
If the test fails (monthly maintenance):  
a. Cut power to heating system from the main power panel and call customer  
service  
For any questions regarding the product installation or  
operation, contact us at:  
7
05 Montrichard  
p When the test is successful, reset the slave unit by switching from ON to  
Saint-Jean-sur-Richelieu, Quebec  
J2X 5K8  
STANDBY then back to ON.  
q Repeat steps 1 to 3 for all slave units.  
Canada  
Tel.: (450) 358-4600  
Toll-free: 1-800-831-AUBE  
Fax: (450) 358-4650  
E-mail: aube.service@honeywell.com  
For more information on our products, visit us at:  
www.aubetech.com  
4
00-230-000-D  
2/7/07  
2/2  

Honeywell RTH5100B Thermostat User Manual

Honeywell 85 3126 Thermostat User Manual

Hunter Fan T201 Thermostat User Manual9160

Honeywell R7426A Thermostat User Manual

Aube CT230 120GB Thermostat User Manual

Hunter Fan 40070 Thermostat User Manual

Honeywell 69 1490 Thermostat User Manual

Aube TH149 Thermostat User Manual

Honeywell RTH2510 Thermostat User Manual

Honeywell L91D Thermostat User Manual