Aube TH115 Thermostat User Manual

TH115 Description

Switch Selection

Control Module Installation

TH115 A/F/AF

Owner’s Guide

This thermostat is factory-set to the following values:

Align the bracket tabs on the control module with the

holes located on top of the power base.

Buttons and symbols

n On/Stand By Switch

Function

Temperature format ^a

°F

°C

Thank you for choosing the Aube TH115,

programmable thermostat that provides both energy

savings and comfort.

Use this switch to put the thermostat in sleep mode

when its use is no longer required (e.g. summer).

This will not affect the clock or programming.

Control module

SW1

SW2

SW3

_E_a_r_l_y_S_t_a_r_tb

Time format

Disable

12-hour

Enable

24-hour

o GFCI Warning Light and Test Button

p Day & Clock Settings

q Programming Mode

a. If you switch from °F to °C or vice versa, the

may need to be redefined.

and

setpoints

b. When using AUTO mode, the thermostat calculates the optimum start

time to obtain the desired temperature by the set time. The heating

system could be started a few hours prior to set time when required.

r Mode Selection/Exit Programming

s Room OR Floor Temperature

t Current Mode and Setpoint

u Current Program Number

v Setpoint definition/Pre-defined Setpoints

w Increase/Decrease Temperature

Switches are

located on the

rear of the control

module.

To modify any

setting, switch

UP or DN.

Models

Power base

Controls the Ambient temperature.

NOTE: Keep the thermostat's air vents clean and free

AF Controls the Ambient temperature and Floor temper-

from obstructions.

ature limit.

Controls the Floor temperature.

NOTE: The screw cannot be removed completely.

First Power ON

GFCI Test (GA & GB power base only)

Temperature Setpoint

Operating Modes

When power is applied for the first

time, the LCD displays: 0:00, MO

The GFCI monitors the electrical flow for

any loss of current; if there is one, the

thermostat will cut off power to the heating

system. We recommend you test the GFCI

immediately after installing the control

module, and once a month thereafter to

ensure it is operating properly. To test:

The following temperature setpoints are pre-programmed:

Correct

Automatic —Executes the schedule.

Default

Symbol

Description

New

n Press MODE until is displayed. The cur-

(Monday),

and temperature (room/

A/AF

rent program number is displayed.

floor).

Comfort (when at home)

70°F

82°F

You can temporary bypass the current pro-

n Press HOUR - MIN to set the

Economy (when asleep/

away from home)

gram by setting a specific temperature

current time.

64°F

68°F

50°F

by pressing on a pre-defined setpoint button (

) .

o Press DAY to set current day.

Vacation (during

The new setpoint will be maintained until the begin-

ning of the next program.

n Increase the temperature

until the

0°F

For AF and F models: one of the two

following messages may be displayed

if the installation is incorrect:

prolonged absence)

heating indicator

is displayed.

To modify a setpoint:

o Press TEST:

n Set the desired temperature using

Manual —Maintains a constant temperature.

n Press MODE until is displayed.

•

Successful: the TEST warning light is ON and

LO: The floor temperature is below

Incorrect

power to heating system is cut off.

o Press and Hold the or or

2°F (0°C), or the temperature

•

Unsucessful: the TEST warning light is OFF. Cut

power to heating system from the main power

panel and call customer service.

button until symbol is displayed.

sensor is defective, or not con-

o Set temperature

or press (

) to use

nected.

p Press RET to exit.

pre-defined setpoint.

The heating indicator

played and the relay is closed

energized).

HI: The floor temperature is above

40°F (60°C), or the tempera-

ture sensor is defective.

is dis-

Floor temperature limit—The floor temperature limit is

p When successful, reset thermostat (Stand By/On) to

82°F. To modify this limit:

Vacation —Maintains the Vacation setpoint

(

power the heating system.

during a prolonged absence.

n Press and hold

o Set temperature

NOTE: If the test warning light comes ON during normal

operation, cut power to heating system from the main

power panel and have an electrician verify the installation.

while switching from

ON to Stand By then

back to On.

ꢀ

Press

until the icon is displayed.

p Press RET to exit.

To avoid damaging your floor, we

recommend

you

the

supplier’s instructions.

20-115-007-00-1-A

Custom Grid

Use this blank grid to record your new schedule.

Pre-programmed Schedule

Modify the Schedule

Remote Input

The TH115 programmable thermostat is pre-programmed

with the following schedule:

Notes:

The TH115 is equipped with a remote input which allows

telephone controller (accessory

Aube CT240) or any other remote control system.

Prog Setpoint

connection of

ꢀ

You can program up to 4 different programs per day.

Each day can have different programs.

It is sometimes faster to program the same schedule

for the entire week and then to modify the exception

days.

ꢀ

When a signal is received through this input, the TH115

will automatically switch from normal operating mode to

Vacation mode ( ), and vice versa when the signal is

removed.

To modify:

n Press PGM to access the programming mode

Activating the Vacation mode

ꢀ

Model: A F AF

Temperature display: °F °C

Time display: 12hrs 24hrs

o Press DAY to select the day to be programmed (hold

There are two ways to activate the Vacation mode:

for 3 seconds to select all days of the week).

n From the thermostat, see “Operating Modes” above.

Time you

wake up and

desired

Time you

leave and

temperature

during your

absence

Time you

return home

and desired

temperature

Time you go

to bed and

overnight

p Press PGM to select the program number.

o From a telephone (remote location). For details on

how to activate using a telephone, refer to the CT240

Instruction Manual.

q Press HOUR and MIN to set the time or press

temperature

CLEAR to clear the time (--:-- is disregarded).

r Repeat steps 2 to 4 for remaining programs.

s When completed, press RET to exit mode.

WARNING: When the Vacation mode is activated

Programs

remotely, it must be deactivated remotely.

6:00 6:00 6:00 6:00 6:00 6:00 6:00

:30 8:30 8:30 8:30 8:30 --:-- --:--

NOTE: After 60 seconds of inactivity, the thermostat will

automatically exit programming mode.

6:00 16:00 16:00 16:00 16:00 --:-- --:--

3:00 23:00 23:00 23:00 23:00 23:00 23:00

Temperature Control

Technical Specifications

Warranty

If you have any questions concerning the

installation or programming of the TH115

programmable thermostat, call our technical

support team at:

AUBE TECHNOLOGIES INC. ONE (1) YEAR LIMITED WARRANTY

The TH115 thermostat works differently than conventional

electromechanical thermostats.

It is equipped with a proportional integral adaptive (P.I.A.)

controller which determines heating cycles by analyzing

the temperature behavior history within the room.

The P.I.A. controller reduces temperature variations

providing an accurate temperature control while

increasing user comfort.

The controller determines the amount of power required

by the heating system to maintain the setpoint

temperature.

Model: TH115 A / AF / F

This product is guaranteed against workmanship defects for a

one year period following the initial date of purchase. During this

period, AUBE Technologies Inc. will repair or replace, at our

option and without charge, any defective product which has been

used under normal conditions.

The warranty does not cover delivery costs and does not apply to

products poorly installed or randomly damaged following

installation.

This warranty cancels and replaces any other manufacturer's

express or implied warranty as well as any other company

commitment. AUBE Technologies Inc. cannot be held liable for

related or random damages following the installation of this

product.

The defective product as well as the purchase invoice must be

returned to the place of purchase or mailed, prepaid and insured,

to the following address:

Display range: 32°F to 140°F (0°C to 60°C)

Setting range (ambient): 40°F to 86°F (5°C to 30°C)

Setting range (floor limit): 40°F to 104°F (5°C to 40°C)

Pre-programmed temperature setpoints:

Phone: Montreal area:(450) 358-4600

Canada / U.S.:1-800-831-AUBE (2823)

(450) 358-4650

Email: service@aubetech.com

ꢀ

Comfort: A/AF: 70°F (21°C) and F: 82°F (28°C)

Economy: A/AF: 64°F (18°C) and F: 68°F (20°C)

Vacation: A/F/AF: 50°F (10°C)

Fax:

Monday to Friday from 8:30 AM to 5:00 PM EST

Floor limit:AF: 82°F (28°C)

Accuracy:± 0.9°F (0.5°C)

For more information on our products, visit us at:

Storage:-4°F to 120°F (-20°C to 50°C)

Temperature control: Proportional integral adaptive,

www.aubetech.com

to 20%

21 to 40% 41 to 60% 61 to 80% 81 to 100%

5-minute or 15-second heating cycles according to the

application and power base.

Aube Technologies Inc.

Memory backup: In the event of a power failure, an

internal circuit will maintain the programming. Only the

time will have to be set if the power failure is more than

two (2) hours. The thermostat will return to the same

operating mode as set before the power failure.

705 Montrichard

Saint-Jean-sur-Richelieu, Quebec, Canada J2X 5K8

As an ENERGY STAR partner, Aube Technologies has

determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

04/08/2003 920-115-007-00-1-A

PB112

Installation Instructions

For models: 120GA / 120GB / 120S / 240GA / 240GB / 240S / 240D

Figure 1

Power

Parts

One (1) power base

Two (2) screws

Four (4) solderless connectors for copper wires

NOTE: Special CO/ALR solderless connectors must be used for connecting

aluminum conductors.

One (1) floor sensor and one (1) flat tip screwdriver (F and AF floor

heating models only).

Load

Guidelines

Turn off power to the heating system at the main electrical panel to

avoid electrical shock. The installation should be carried out by an elec-

trician.

Figure 2

ꢀ

High voltage thermostats must be installed onto an electrical box.

For a new installation, choose a location about 5 ft. above the floor and

on an inside wall.

ꢀ

The thermostat must be installed on an inside wall facing the heating

system (except for floor heating systems).

Avoid locations where there are air drafts (top of staircase, air outlet),

dead air spots (behind a door), direct sunlight or concealed chimneys or

stove pipes (except for floor heating systems).

Procedure

Connect the power base wires to the power supply and load using sold-

erless connectors for copper wires (figure 1).

Technical Specifications

If your thermostat is type F or AF (not A), insert the floor sensor wires

through one of the two holes below the terminals (figure 2) and connect

the wires to terminals 3 and 4 (no polarity).

Model

Supply

Max. Load

Power

Wiring

GFCI

20GA 120 VAC, 50/60Hz

20GB 120 VAC, 50/60Hz

15 A

1800 W 4w/DP

5 mA

The wires must run alongside the terminals and not go over them. The

wire must not cross any heating wires nor be placed directly on a heating

wire or adjacent to it. For best performance, the sensor probe should be

centered between the wires in the mat.

1800 W 4w/DP 30 mA

2000 W 4w/SP

3600 W

120S

120 VAC, 50/60Hz

40 VAC, 50/60Hz

208 VAC, 50/60Hz

16.7 A

40GA

40GB

15 A

4w/DP

5 mA

If you wish to use a remote controller such as the CT240 or CT241,

3120 W

insert the cable (use 18 to 22 gauge flexible wires) into one of the two

holes available below the terminal board and connect to terminals 1 and

240 VAC, 50/60Hz

08 VAC, 50/60Hz

3600 W

3120 W

4w/DP 30 mA

4w/SP

of the base (figure 2).

40 VAC, 50/60Hz

08 VAC, 50/60Hz

4000 W

3475 W

Push the excess length of the high-voltage wires back into the electrical

box.

240S

240D

16.7 A

15 A

40 VAC, 50/60Hz

08 VAC, 50/60Hz

3600 W

3120 W

Secure the power base to the electrical box using the provided screws.

4w/DP

If necessary, set the configuration switches on the control module (refer

to the control module user guide).

Storage: -4°F to 120°F (-20°C to 50°C)

Remote controller input (ECONO): requires a dry contact

Size (H • W • D): 4.89 x 2.76 x 0.91 in. (124 x 70 x 23 mm)

Install the control module onto the base.

Apply power to heating system.

Models:

Certifications:

120 GA / GB

20S / 240S

40 GA / GB

240D

PB112

400-112-006-B

1/6/05

1/1