Honeywell 69 0786 2 Thermostat User Manual

Home

href="
T8132C Programmable Thermostat  
OWNER’S GUIDE  
Weekday/Weekend Programmable  
Heat and/or Cool Thermostat  
and Mounting Plate  
69-0786-2  
Welcome to the world of comfort and energy  
savings with your new Honeywell Program-  
mable Thermostat.  
Direct questions concerning the operation of  
this thermostat to Honeywell Customer  
Assistance at 1-800-468-1502, Monday-Friday  
7:00 a.m.-5:30 p.m., Central time.  
Your new T8132C Thermostat automatically  
controls the temperature in your home, keeping  
you comfortable while saving energy when  
programmed according to the instructions in  
this manual.  
2
69-0786—2  
Table of Contents  
Page  
Programming Thermostat ...............................................................................................................  
Program Schedule ..........................................................................................................................  
T8132C Programming Guide ..........................................................................................................  
4
6
8
Setting Fan and System Switches .................................................................................................. 12  
Changing Batteries.......................................................................................................................... 13  
Troubleshooting Guide .................................................................................................................... 15  
Limited One-Year Warranty .................................................................................... Inside Back Cover  
IMPORTANT  
Although the thermostat has a low  
As a precaution, when leaving home for longer  
than a month, change batteries before you  
leave to prevent the system from shutting down  
due to lack of battery power.  
battery indicator, replace the batteries  
once a year to prevent the thermostat  
and heating/cooling system from  
shutting down due to lack of battery  
power.  
3
69-0786—2  
Select WAKE if you want the house at a  
comfortable temperature when you get up,  
while you get ready for work or school. When  
deciding what time to set for your WAKE  
period, include extra lead time, depending on  
the outside temperature and your furnace  
response time, to give the furnace a head start  
to heat the house before you get up. (This will  
be a higher temperature during heating  
season, or a lower temperature during cooling  
season.)  
Programming Thermostat  
When you program the thermostat, set one  
schedule for weekdays and another for  
weekends, because your temperature require-  
ments probably vary. (During weekends, only  
the WAKE and SLEEP time periods are  
available.)  
Use the personal Program Schedule for  
planning your program schedule of time and  
temperature settings for various times of the  
day.  
Select LEAVE if you want an energy-saving  
temperature while you are away at work or  
school. (This will be a lower temperature during  
heating season, or a higher temperature during  
cooling season.)  
Four time periods are available during week-  
days—WAKE, LEAVE, RETURN, and SLEEP.  
View these periods individually on the display  
when you press the Set Schedule key.  
4
69-0786—2  
Select RETURN if you want the house at a  
comfortable temperature for activities before  
bedtime. When deciding what time to set for  
your RETURN period, include extra lead time,  
depending on the outside temperature and  
your furnace response time, to give the furnace  
a head start to heat the house before you  
arrive home. (Again, higher for heating or lower  
for cooling.)  
controls heating at 68°F (20°C) and cooling at  
78°F (26°C), 24 hours a day. Also, you do not  
need to enter a time and temperature program  
for all periods if your schedule does not require  
it. For example, a house that is occupied  
during weekdays would not require programs  
for LEAVE and RETURN.  
When pressing the keys, use the ball of your  
finger or a soft pencil eraser.  
Select SLEEP if you want an energy-saving  
temperature while you are sleeping. (For more  
comfortable sleeping, some homeowners  
choose not to raise the cool temperature during  
the night.)  
NOTE: Using sharp fingernails or pencil  
points can damage the keypad.  
If you make an error at any time during  
programming, press the Run Program key,  
and continue again at the last step.  
Fill in the times and temperatures you desire  
for weekdays and weekends. If you decide not  
to program the thermostat, it automatically  
5
69-0786—2  
href="
Program Schedule  
Weekdays  
HEATING PROGRAM SCHEDULE  
Start Time Heating Temperature  
2
WAKE  
1
LEAVE  
RETURN  
SLEEP  
1
Weekends  
WAKE  
1
SLEEP  
1
2
WAKE and RETURN start times should include extra lead time, based on outside temperature  
and furnace response time, to give your furnace a head start to heat the house.  
The temperatures cannot be set any higher than 88°F (31°C) or set any lower than 45°F (7°C).  
6
69-0786—2  
href="
COOLING PROGRAM SCHEDULE  
Start Time Heating Temperature  
Weekdays  
WAKE  
2
1
LEAVE  
RETURN  
SLEEP  
1
Weekends  
WAKE  
1
SLEEP  
1
2
WAKE and RETURN start times should include extra lead time, based on outside temperature  
and furnace response time, to give your furnace a head start to heat the house.  
The temperatures cannot be set any higher than 88°F (31°C) or set any lower than 45°F (7°C).  
NOTE: If you decide not to program the thermostat, it automatically controls heating at 68°F  
(20°C) and cooling at 78°F (26°C), 24 hours a day.  
7
69-0786—2  
href="
T8132C Programming Guide  
NOTE: Batteries are required for operation and programming. When replacing the batteries, set  
the system switch to OFF. Remove the battery door (on the thermostat left side) using a  
coin at the bottom. Follow the instructions in Changing Batteries section.  
Set Current Time/Day  
To set time, press and release  
Ahead  
Back  
Set  
Clock/Day  
once, and press  
until current time shows; to set the  
Ahead  
Set  
day, press and release  
Clock/Day  
Run  
again, and press  
until current day shows; then press  
.
Program  
Back  
Heating Program  
Weekday  
With the system switch at HEAT, press and release Schedule once. WAKE, MON-FRI and SET  
appear on display.  
8
69-0786—2  
href="
Ahead  
Back  
Warmer  
Cooler  
Press  
to program the WAKE time and press  
to program the WAKE temperature  
for MON-FRI. Repeat the sequence for LEAVE, RETURN, and SLEEP.  
Ahead  
Back  
Weekend  
Schedule  
Press  
until SAT SUN, WAKE and SET appear on the display. Press  
to program WAKE  
Warmer  
time and press  
to program WAKE temperature for Sat-Sun. Repeat the sequence for SLEEP.  
Cooler  
Cooling Program  
With the system switch at COOL, follow the same instructions as for Heating Program.  
Run  
Program  
After programming, adjust fan and system switches, as desired. Press and release  
the program.  
to start  
9
69-0786—2  
href="
A quick guide for operating or making changes follows.  
NOTE: Set system switch to HEAT or COOL to perform the following:  
Warmer  
Temporarily Change temperature for current period only—press  
; temperature is  
Cooler  
Run  
Program  
cancelled at next scheduled change; to cancel sooner, press  
.
Warmer  
Hold  
Run  
Hold a temperature indefinitely—press  
,
; to cancel, press  
.
Program  
Temp  
Cooler  
Present  
Setting  
Check Current Temperature Setting—press  
.
1
0
69-0786—2  
href="
Weekday  
Schedule  
Weekend  
Schedule  
Check Programs—press  
,
repeatedly to see each time and temperature; then  
Run  
Program  
press  
.
Weekday  
Schedule  
Weekend  
Schedule  
Cancel a program—press  
,
until program to cancel shows; then press  
Clear  
.
Check Usage — press Usage to determine length of time heating or air conditioning has been on  
since midnight; press again for yesterday’s usage, and again for cumulative usage; press  
Clear  
to  
Run  
Program  
clear cumulative reading, if desired; then press  
.
Permanently Change a program—repeat steps in Heating Program or Cooling Program sections  
page 5 and 6), as applicable.  
(
Run  
Program  
Return to normal program or start program —press  
.
Questions?  
Call Honeywell  
Customer Assistance  
1
-800-468-1502.  
1
1
href="
Setting Fan and System Switches  
First set the fan switch.  
AUTO: Normal setting for most  
homes. A single-speed fan  
turns on automatically with the  
Then set the system switch.  
Auto  
On  
COOL: The thermostat  
controls your air  
Cool  
Off  
Heat  
conditioning system.  
air conditioner or furnace. A two-speed fan  
usually runs on high with the air conditioner  
and runs on low with the furnace.  
Cool  
Cool  
Off  
Off  
Heat  
Heat  
OFF: Both the heating and  
air conditioning systems  
are off.  
Auto  
On  
ON: The fan runs continuously.  
Use for improved air circulation  
during special occasions or for  
HEAT: The thermostat controls  
your heating system.  
more efficient electronic air cleaning.  
1
2
69-0786—2  
href="
possible after the indicator starts flashing. If  
you do not replace the batteries when the  
indicator light is flashing bAt Lo, the indicator  
stops flashing. When the batteries are almost  
completely dead, bAt Lo stays on without  
flashing to indicate the thermostat and heating/  
cooling system have stopped working.  
Changing Batteries  
IMPORTANT  
Batteries are required for program-  
ming and operation of the thermostat  
and heating/cooling system.  
As the batteries run  
low, bAt Lo  
indicator  
flashes  
for one  
to two  
months  
before  
the batteries  
run out com-  
pletely. Replace the  
batteries as soon as  
After the batteries are completely dead, the bAt  
Lo indicator disappears, leaving a completely  
blank display.  
Use two AA alkaline batteries; nonalkaline  
batteries do not last as long. We recom-  
mend Energizer® batteries.  
REMOVING  
BATTERY  
DOOR  
Make sure the thermostat is set to the OFF  
position.  
Use a coin to remove the battery door.  
M1719C  
1
3
69-0786—2  
href="
INSTALL TWO AA ALKALINE  
BATTERIES AS SHOWN  
To remove batteries, press down on the left  
ends of the batteries. If you insert new batter-  
ies within 20 to 30 seconds of removing the old  
ones, the thermostat does not require repro-  
gramming. However, if the display is blank, the  
batteries are dead or incorrectly installed and  
the thermostat requires reprogramming.  
Install the fresh batteries, as shown, making  
sure positive and negative terminals are  
oriented correctly.  
Replace the battery door.  
M1713  
1
4
69-0786—2  
Troubleshooting Guide  
IF…  
THEN…  
Display will not come on.  
 Set the system switch to OFF; remove batteries and  
insert them backward for at least five seconds to reset  
the thermostat; replace the batteries correctly. The  
display should come on.  
Make sure the batteries are fresh and installed correctly.  
Temperature display will not go  
 The temperature setting limit was reached. The  
setting range is 45°F to 88°F (7°C to 31°C).  
lower than 45°F (7°C) or higher than  
88°F (31°C) during programming.  
Temperature change occurs at the  
wrong times.  
 Verify the program times for the period. Be sure that  
AM and PM indications are correct. Make sure the current  
day and time are correct. Reprogram, if necessary.  
Heating will not come on.  
 Check that the switch on the thermostat is set to HEAT.  
Check the system fuse or circuit breaker and replace or  
reset, if necessary.  
1
5
69-0786—2  
Heating will not come on (Cont).  
Cooling will not come on.  
 If display is blank or displays bAt Lo, install fresh  
batteries.  
If temperature setting is higher than current temperature,  
and thermostat displays HEAT, contact Honeywell  
Customer Assistance at 1-800-468-1502.  
 Check that the switch on the thermostat is set to  
COOL.  
Check the system fuse or circuit breaker and replace or  
reset, if necessary.  
If display is blank or displays bAt Lo, install fresh  
batteries.  
The thermostat has a built-in time delay on cooling.  
Allow five to ten minutes after changing the setting  
before the air conditioner starts.  
If the temperature setting is lower than the current  
temperature, and the thermostat displays COOL, move  
the system switch from COOL to OFF for ten minutes.  
After ten minutes, return the switch to the COOL  
1
6
69-0786—2  
Cooling will not come on (Cont).  
position. If the air conditioner comes on, the compressor  
could have reached its high limit temperature protection  
and shut down. If the air conditioner does not come on  
after ten minutes and displays COOL, contact Honeywell  
Customer Assistance at 1-800-468-1502.  
The house is too warm or too cool.  Press Present Setting key to check the current  
temperature setting.  
If desired, change the temperature setting. See  
page 5.  
SYSTEM ON indicator is lit, but no  
heat is coming from the registers.  
 Allow time for the furnace to heat up and the fan to  
come on before checking for heat at the register.  
The current thermostat  
setting does not match the  
display temperature.  
 Be aware that it is normal for the current setting  
and display temperature to differ occasionally.  
bAt Lo remains on display after  
fresh batteries are installed.  
 Remove the batteries. Wait one hour. Install fresh  
alkaline batteries.  
1
7
69-0786—2  
href="
TYPICAL ENERGY SAVINGS FOR REPRESENTATIVE CITIES IN THE U.S. AND CANADA  
Savings for Once-A-Day  
0°F (5°C) decrease  
Savings for Twice-A-Day  
10°F (5°C) decrease*  
Savings for 5°F (3°)  
summer increase  
1
30%  
28%  
26%  
24%  
22%  
20%  
18%  
1
6%  
4%  
1
1
2%  
0%  
1
8
%
%
%
6
4
2
% Minneapolis  
St. Paul  
Montreal  
Ottawa  
Toronto  
Edmonton  
Regina  
Winnipeg  
Calgary  
Halifax  
Vancouver  
Buffalo  
Cleveland  
Milwaukee  
Denver  
Des Moines Chicago  
Omaha  
Salt Lake  
City  
Boston  
Cincinnati  
Kansas City Philadelphia Portland  
Wash., D C  
New York  
Louisville  
San  
Francisco  
Dallas  
Atlanta  
Los Angeles  
San Diego  
Moncton  
North Bay  
Quebec  
Detroit  
Pittsburgh  
Indianapolis  
St. Louis  
Seattle  
Columbus  
St. John's  
*Based on 10°F (5°C) decrease—(5°F (3°C) decrease  
gives approximately 55 percent of these savings).  
M2416A  
1
8
69-0786—2  
Limited One-Year Warranty  
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a  
period of one (1) year from the date of purchase by the consumer. If, at any time during the warranty period, the product is defective or malfunctions,  
Honeywell shall repair or replace it (at Honeywell’s option) within a reasonable period of time.  
If the product is defective,  
(
i) return it, with a bill of sale or other dated proof of purchase, to the dealer or contractor from which you purchased it, or  
(ii) package it carefully, along with proof of purchase (including date of purchase) and a short description of the malfunction, and mail it, postage  
prepaid, to the following address:  
Honeywell Inc.  
Return Goods Department  
1
050 Berkshire Lane  
Plymouth, MN 55441-4437  
This warranty does not cover removal or reinstallation costs. This warranty shall not apply if it is shown by Honeywell that the defect or  
malfunction was caused by damage which occurred while the product was in the possession of a consumer.  
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE  
FOR ANY LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR  
INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT. Some states  
do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED  
WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED  
TO THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above  
limitation may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.  
If you have any questions concerning this warranty, please write our Customer Assistance Center, Honeywell Inc., P.O. Box 524, Minneapolis, MN  
5440-0524 or call 1-800-468-1502, Monday-Friday, 7:00 a.m. to 5:30 p.m., Central time. In Canada, write Retail Products ON30, Honeywell Limited/  
5
Honeywell Limitée, 155 Gordon Baker Road, North York, Ontario M2H 2C9.  
1
9
69-0786—2  
href="
Toll-free Customer Assistance  
For all questions concerning this thermostat, please read and follow the instructions. If additional  
assistance is needed, call Honeywell Customer Assistance toll-free at 1-800-468-1502, Monday-  
Friday, 7:00 a.m.-5:30 p.m. Central time.  
Before you call, please have the following information available: Thermostat model number and  
date code, and type of heating/cooling system (for example, hot water, warm air, oil and gas).  
Home and Building Control  
Home and Building Control  
Honeywell Limited-Honeywell Limitée  
155 Gordon Baker Road  
North York, Ontario  
Helping You Control Your World  
Honeywell Inc.  
1
985 Douglas Drive North  
Golden Valley, MN 55422  
M2H 2C9  
69-0786—2 Rev. 5-96 J.S. Printed in Mexico  
Copyright © 1996 Honeywell Inc. All Rights Reserved  

Honeywell TB8220U Thermostat User Manual

Honeywell TH8321U1014 Thermostat User Manual

Honeywell RTH6450 Thermostat User Manual

White Rodgers 1F83 0471 Thermostat User Manual

White Rodgers 1F97 0671 Thermostat User Manual

White Rodgers 1F95 71 Thermostat User Manual

Emerson 1F85ST 0422 Thermostat User Manual

Honeywell R7851C Thermostat User Manual

Lux Products TX1500E Thermostat User Manual

White Rodgers 1F90W 51 Thermostat User Manual