How do I install the batteries?
How do I set my own daily temperature pro-
gram?
I am going on holiday for a few days. How do I
save energy but ensure that the house is warm
when I return?
HC60 Relay Box Controls Layout
1
.
Lift up the front flap to reveal the battery compartment. Open the
battery compartment by inserting a coin underneath the bottom
right edge of the flap and lift out.
The relay box will normally be found mounted close to the boiler.
1
.
Press PROG 1. The first temperature change time and tempera-
ture level will flash to indicate they can be changed. (the two small
arrows are displayed only when the programmed temperature level
is shown).
1
. Make sure the CM61NG is in AUTO or MAN mode.
2
.
Pull the paper tab out to activate the 2 AA LR6 Alkaline Batteries
included and push the battery compartment firmly back into the
front of the unit. After a pause the unit will now display information.
2. Press
temperature.
3. Press
Press TEMP
0°C).
(HOLIDAY) to display the holiday days counter and
Push button and relay
status LED’s
+ or - to set the holiday time (1 - 99 days).
4
.
or
to set the holiday temperature (5°C -
3
1
2
3
4
5
6
The unit will control to the new temperature for the set number of days
holiday. At midnight the holiday counter will be reduced by one until the
selected number of days have passed. The unit will then return to
normal control as set by the MAN or AUTO position.
What does it mean when the HC60NG relay box
green LED is ON?
2
.
Press
+ or - to adjust the first temperature change time.
Holding the button down will change the time quickly. The change
time can be set in 10 minute steps from 03:00 in the morning. The
change time can be adjusted up to 02:50 on the next morning, so
you can maintain the evening temperature after midnight.
To cancel the HOLIDAY setting, press the
button a second time.
The green LED indicates normal operation of the radio frequency
system. When the green LED is ON the boiler is also ON. When the
LED is OFF the boiler is OFF.
(
Note: If you attempt to move a change time past the next change
How can I switch the Heating on and off
manually?
time, both times will be moved).
When do I need to use the push button?
3
4
5
.
.
.
Press TEMP
or
to adjust the first temperature level.
To switch the boiler ON or OFF:
1. Press the MAN button.
You should use the push button to control your boiler only when the RF
communication is lost (see the CM61NG Trouble-Shooting Guide).
Holding the button down will change the temperature quickly. The
temperature can be set in 0.5°C steps from 5°C to 30°C.
2. Press TEMP
or
until the boiler switches ON or OFF.
CM61NG Controls/Display Layout
The diagram below details the key button functions and display
information.
Press PROG 2 to display the second temperature change time and
What other accessories can I buy for the CM61NG?
temperature level. Set these by pressing
or
+ or - and TEMP
How can I switch the CM61NG off?
.
Automatic Time Setting (ATS) “Add-On” Module *
(Part No. Q6667B1015)
Press the OFF button. The unit will now control at 5°C.
Battery Low
Indicator
Time Display Heat Demand Temperature
The remaining temperature changes can be displayed by pressing
PROG buttons 3, 4, 5 and 6 and adjusted by using + or - and
TEMP or . (If you don’t want to use all the temperature
change times 2, 3, 4, 5 or 6 refer to the section “What if I don’t
want to use all 6 temperature change times?”).
Indicator
Display
Information
Enquiry
Button
How do I know when the batteries need to be
changed and how do I do this?
Time
Change
Buttons
Your CM61NG has built-in electronics that constantly monitor the
battery power level. With no accessory fitted the batteries should last
about 2 years. When the batteries need replacing, a flashing
symbol will be displayed.
Temperature
Change
Buttons
6
.
Press AUTO when you have completed your programming, The
CM61NG will now control the room temperature to match your
program.
NG
=
=
increase
decrease
Automatic
Function
Button
To change the batteries:
Battery
Compartment
What if I don’t want to use all 6 temperature
change times?
1
.
Lift up the front flap to reveal the battery compartment. Open the
battery compartment by inserting a coin underneath the bottom
right edge of the flap and lift out.
The ATS module picks up a daily time signal from a transmitter in
Central Europe and corrects the time on the CM61NG display. So:
Manual Function
Button
Program
Buttons
Off Button
Holiday Button
The built-in program uses 6 temperature change times as indicated by
the numbers 1, 2, 3, 4, 5 and 6 on the display. Unwanted change times
can be deleted by holding the appropriate PROG buttons (2, 3, 4, 5 or
2. Replace the used batteries with 2 new AA LR6 Alkaline Batteries
Duracell are recommended) and push the battery compartment
•
•
You never need to set or adjust the time
There is no need to adjust the unit by -/+ 1 hour in summer / winter
since the unit does this automatically
(
firmly back into the front of the unit.
6) down for a few seconds. The change time will be removed and the
•
Your CM61NG is the most accurate clock in your home so you
can use this information to set-up all your other clocks.
display will show dashes instead of a time / temperature display.
How do I set the time?
RESPECT YOUR ENVIRONMENT!
Take care to dispose of used batteries carefully.
The time can be set with the CM61NG in the AUTO, MAN or OFF
operating modes. Press + or - until the correct time is displayed.
Each button press will change the time by one minute. Holding the
button down for a few seconds will change the time slowly at first, then
quickly. Make sure AM or PM is correct.
Deleted temperature change times can be brought back by again
pressing the appropriate program button (2, 3, 4, 5 or 6) for a few
seconds.
*
Not available in all Geographic Regions depending on transmitter
range and home location.
The CM61NG has a permanent memory to keep your program
settings. While you change the batteries, you should never need to
reprogram. However, if you take more than one minute to change
Table stand for the room unit (Part No. F42010248-002)
Can I change the programmed temperature for a
short time?
them, you may need to correct the time by pressing
+ or -.
If you do not want to mount the room unit on the wall you can use
optional table stand, ask you installer for details
When the CM61NG is in AUTO position (display will show “AUTO”)
Can I use my CM61NG to control my air-condi-
tioning system?
PM
the temperature can be adjusted temporarily by pressing TEMP
The temperature will return to the program at the next temperature
change time.
or
.
Yes. Please refer to your installer for more information.
How do I get started with the built-in tempera-
ture program?
How do I check the programmed temperature?
How do I remove the CM61NG from the wall
bracket?
In normal operation the temperature displayed is the actual room
Press the AUTO button.
The CM61NG will now control your heating using the built-in
temperature program:-
temperature. To check the programmed temperature press and the
display will show the programmed temperature with the two small
arrows.
*
Note: The room unit must be located in a location where reliable
communication was proven. Advise your installer where you would like
to position the room unit and they will check if the RF communication
is reliable in the selected location(s)
Daily
Program
Time
1
2
3
4
5
6
How do I set one temperature for the whole
day?
06:30 08:00 12:00
21°C 18°C 21°C
2:00
18°C
6:00
21°C
10:30
16°C
Temperature
To operate as a simple thermostat with one temperature throughout the
day, press MAN. Adjust the manual temperature by pressing TEMP
After programming is finished always replace the CM61NG back on
the wall bracket.
or
. The manual temperature can be set anywhere from 5°C to 30°C
in 0.5°C steps.