V4062A,B,D HI-LO-OFF FLUID POWER GAS VALVE ACTUATOR
6
-3/4 (171.5)
INSTALLATION
3-23/32
(94.5)
5 (127.0)
2
7/32
When Installing This Product…
(21.4)
1
. Read these instructions carefully. Failure to follow them
could damage the product or cause a hazardous
condition.
1
-9/32
(32.5)
2. Check the ratings given in the instructions and on the
product to make sure the product is suitable for your
application.
1
A
3
. Installer must be a trained experienced, flame
safeguard control technician.
4
. After installation is complete, check out product
operation as prided in these instructions.
KNOCKOUT
FOR 1/2 INCH
CONDUIT (4)
WARNING
B
Electrical Shock Hazard.
Can cause serious injury or death.
Disconnect power supply before making wiring
connections to prevent electrical shock and
equipment damage.
VALVE
VALVE
IMPORTANT
. All wiring must comply with all applicable electrical
1
ALLOW 4 IN. (101.6 MM) CLEARANCE FOR ACTUATOR REMOVAL.
V5055 V5097
1
codes, ordinances, and regulations. All wiring must
be NEC Class 1.
2. Voltage and frequency of the power supply
connected to this control must agree with those
marked on the device.
DIM A
DIM B
MM
DIM A
DIM B
VALVE SIZE
INCH
IN.
MM
IN.
IN.
MM
IN.
MM
3
1
1
1
2
2
3
4
/4
11-1/8
11-1/8
11-1/8
11-1/8
11-1/4
11-3/4
11-3/4
14-1/8
282.6 2-3/4
282.6 2-3/4
282.6 2-3/4
282.6 2-3/4
285.8 2-7/8
298.5 3-3/8
298.5 3-3/8
69.9
69.9
69.9
69.9
73.0
85.7
85.7
11-1/8
11-1/8
11-1/8
11-1/8
11-3/4
11-3/4
11-3/4
—
283
283
283
283
298
298
298
—
2-3/4
2-3/4
2-3/4
2-3/4
3-3/8
3-3/8
3-3/8
—
70
70
70
70
86
86
86
—
3
4
5
. Loads connected to the auxiliary switch and/or
proof-of-closure switch, if used, must not exceed
the ratings given in the Specifications section.
. When replacing a V6034 Actuator with a V4062, the
V5034 Valve body must be changed to a V5055
Valve.
. Do not attempt to use the V4062 Actuator with the
V4055/V5034 Adapter. Differences in stem travel
can prevent correct low fire adjustment.
-1/4
-1/2
-1/2
358.8 5-13/16 147.6
M10981
Fig. 1. Approximate mounting dimensions
of V4062 Actuators in in. (mm).
Install Valve
Ambient Operating Temperature Rating:
The actuator is installed directly on the V5055/V5097 body
after the valve is installed in the gas supply line. Refer to the
instructions packed with the V5055/V5097 Gas Valve for
installation details. When installing the valve, assure that:
-
-
40° to 150°F (-40° to 66°C) for 60 Hz models;
10° to 158°F (-23° to 70°C) for 50 Hz and 50/60 Hz
models.
1
2
3
. Sufficient clearance is allowed for actuator installation
and service.
. Ambient temperatures at the valve location do not
exceed actuator ratings.
. Position of the valve permits damper hookup if one is
controlled.
Approvals:
Underwriters Laboratories Inc. Listed: File No. MH1639,
Guide No. YIOZ.
Factory Mutual: Approved.
International Approval Services (Joint Venture of the
American Gas Association [AGA] and the Canadian
Gas Association [CGA]): Certified 60 Hz models only.
Industrial Risk Insurers Acceptable.
Some V4062 Actuators are approved as Class A valves in
accordance with EN161:
Install Accessory Switches (If Needed)
An spdt switch can be installed to operate an auxiliary load
up to 1/2 hp (0.37 kW). The switch can be adjusted to
operate at any point in the valve stroke.
When used with V5055 Valves: Pin: CE-0063AR1359.
When used with VE5000 Series Valves: Pin: CE-
0
063AP3075.
A proof-of-closure switch can also be installed with a V5055/
V5097C or E Valve (with double seal) on any V4062 Actuator
to provide a valve seal overtravel interlock. The spdt proof-of-
closure switch is installed to make or break a circuit when
the valve is in the closed position. The switch is not
adjustable.
Accessories:
1
1
33568 Auxiliary Switch Bag Assembly.
33569 Proof-of-Closure Switch Bag Assembly. (Must be
used with a V5055/V5097C or E with double seal).
35796 Wrench (included with the actuator).
1
7
616BR Damper Crank Arm (damper arm and clip).
60-2099—8
4