Carrier TB PAC Thermostat User Manual

Home

T B --- PA C

T B --- P H P

Base Series Programmable Thermostats

Installation Instructions

included in literature and attached to the unit. Consult local

building codes and the current editions of the National Electrical

Code (NEC) NFPA 70.

Designed and Assembled

in the USA.

In Canada, refer to the current editions of the Canadian Electrical

Code CSA C22.1.

US patents: US20060165149 A1, USD578026 SI, US6205041 B1

Recognize safety information. This is the safety -- alert symbol

When you see this symbol on the unit and in the instructions or

manuals, be alert to the potential for personal injury.

Understand the signal words DANGER, WARNING, and

CAUTION. These words are used with the safety -- alert symbol.

DANGER identifies the most serious hazards which will result in

severe personal injury or death. WARNING signifies a hazard

which could result in personal injury or death. CAUTION is used

to identify unsafe practices which may result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which will result in enhanced installation, reliability, or

operation.

INTRODUCTION

There are two Base Series programmable thermostat models, one

for AC applications and one for HP applications. Both are dual

powered, operating from either 24VAC or two alkaline AA

batteries. Configuration and program schedules are stored in

non -- volatile memory, preserving this information during power

loss and battery removal. Features include simplified 5/2 day

programming, large backlit display, and modern styling.

A07107

Base Series Programmable Thermostat

NOTE: Read the entire instruction manual before starting the

installation

TABLE OF CONTENTS

The AC model provides one stage of heating and one stage of

cooling.

PAGE

SAFETY CONSIDERATIONS . . . . . . . . . . . . . . . . . . . . . . . . . 1

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

INSTALLATION CONSIDERATIONS . . . . . . . . . . . . . . . . . . . 1

INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 1 — Thermostat Location . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 2 — Install Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Step 3 — Set Thermostat Configuration . . . . . . . . . . . . . . . . . 3

Step 4 — Understand Thermostat Operation . . . . . . . . . . . . . . 3

Step 5 — Check Thermostat Operation . . . . . . . . . . . . . . . . . . 4

WIRING DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

The HP model provides two stages of heating and one stage of

cooling.

INSTALLATION CONSIDERATIONS

AC Operation

For 24VAC operation, both the R and C wires must be connected

to the 24VAC power source. Batteries are not needed.

Battery Operation

When batteries are used, the common (C) connection is not needed,

saving a wire, and eliminating 24VAC operation. The thermostat

continues to operate in the event of a power failure. Battery life is

expected to be one year. A “low battery” reminder tells the

homeowner when it is time to replace the batteries. When

connected without the common wire, the thermostat will not

operate without batteries. Continuous back -- lighting is not

available.

SAFETY CONSIDERATIONS

Improper installation, adjustment, alteration, service, maintenance,

or use can cause explosion, fire, electrical shock, or other

conditions which may cause death, personal injury, or property

damage. Consult a qualified installer, service agency, or your

distributor or branch for information or assistance. The qualified

installer or agency muse use factory -- authorized kits or accessories

when modifying this product. Refer to the individual instructions

packaged with the kits or accessories when installing.

Both Battery and AC Operation

If both batteries and 24VAC operation are used (batteries installed

and the common wire connected), and indefinite clock operation

are provided, the battery will be used only during AC power loss,

extending battery life to nearly its shelf life.

Follow all safety codes. Wear safety glasses, protective clothing,

and work gloves. Have a fire extinguisher available. Read these

instructions thoroughly and follow all warnings or cautions

A jumper has to be properly set for backlight operation. J2 should

be set in the “AC” position when the thermostat is operated from

24VAC. J2 should be set in the “BAT” position when the

thermostat is operated from batteries. The thermostat will continue

to operate if J2 is not in the correct position or not connected.

However, the backlight will not operate.

6. Secure back plate to wall with 2 anchors and screws

provided making sure all wires extend through hole in

plastic.

NOTE: Anchoring the back plate will maximize proper mounting

plate flatness and allow latch to fully engage.

INSTALLATION

IMPORTANT: Install batteries last to ensure proper thermostat

mounting and latch engagement.

. Connect wires to proper terminal location on backplate.

. Push any excess wire back into wall. Seal hole in wall to

prevent air leaks. Leaks can affect thermostat operation.

Any excess wire left inside thermostat casing may also af-

fect thermostat operation by interfering with airflow across

the temperature sensor.

Step 1 — Thermostat Location

Thermostat should be mounted:

S Approximately 5 ft (1.5m) from floor.

S Close to or in a frequently used room, preferably on an inside

partitioning wall.

9. Set the thermostat front housing into the (2) latches

notches) on the bottom of the back plate.

(

S On a section of wall without pipes or duct work.

Thermostat should NOT be mounted:

S Close to a window, on an outside wall, or next to a door leading

to the outside.

S Exposed to direct light and heat from the sun, a lamp, fireplace,

or other heat -- radiating object which may cause a false reading.

S Close to or in direct airflow from supply registers and return -- air

grilles.

S In areas with poor air circulation, such as behind a door or in an

alcove.

Step 2 — Install Thermostat

IMPORTANT: Install batteries last to ensure proper thermostat

mounting and latch engagement.

A08429

0. Rotate the front housing forward and press on the faceplate

with thumbs near the Up/Down arrows on the right and the

WARNING

“

H/C” and fan symbols on the left side of the display. Do

this with a moderate amount of pressure.

ELECTRICAL OPERATION HAZARD

Failure to follow this warning could result in personal injury

or death.

Before installing thermostat, turn off all power to unit. There

may be more than 1 disconnect. Lock out and tag switch with

a suitable warning label.

. Turn OFF all power to HVAC unit.

. If an existing thermostat is being replaced:

a. Remove existing thermostat from wall.

b. Disconnect wires from existing thermostat, one at a

time. Be careful not to allow wires to fall back into wall.

c. As each wire is disconnected, record wire color and

terminal marking.

A08430

d. Discard or recycle old thermostat.

11. If necessary, continue to rotate the front housing forward

and press to engage the top corner latches.

CAUTION

ENVIRONMENTAL HAZARD

Failure to follow this caution may result in environmental

damage.

Mercury is a hazardous waste and may be found in the old

thermostat. Federal regulations require that Mercury be

disposed of properly.

. Separate front and back plastic assembly of thermostat.

. Route thermostat wires through hole in mounting base.

Level mounting base against wall (for aesthetic value only,

thermostat need not be level for proper operation) and mark

wall through 2 mounting holes.

A08431

12. Snap thermostat together making sure assembly is secure.

. Drill two 3/16 -- in. (5mm) mounting holes in wall where

marked.

13. Install the batteries.

4. Turn ON power to unit.

signal. Some auxiliary heaters require a separate G signal to operate

the blower when W is applied.

This option allows a HP thermostat to control an AC system.

On power up, depending on the thermostat model being used, the

LCD readout will display either AC for air conditioner model

(

1 -- stage heat/1 -- stage cool) or HP for heat pump model (2 -- stage

Option 10 -- Reversing valve

heat/1 -- stage cool).

Selections: C = reversing valve energized in cooling —This is

default.

Step 3 — Set Thermostat Configuration

Configuration options enable the installer to configure the

thermostat for a particular installation.

H = reversing valve energized in heating — Only

appears in HP systems.

These are not presented to the homeowner and therefore must be

properly set by the installer. Following is a list of the options

available, an explanation of their function, and their factory default

settings. Not all numbers are used in the Base Series because not all

options are available in this series.

Option 13 -- Room Air Temperature Offset

Selections: ±5_F /3_C. Default is 0.

The number of degrees to be added to the displayed temperature to

calibrate or deliberately miscalibrate the measured room

temperature. This option is in _F even if Option 3 is set for _C.

Configuration Options -- Summary:

Option 01 -- Equipment type

Option 21 -- Keypad Lockout

Selections: ON, OF — Default is OF.

Option 03 -- Fahrenheit/Centigrade

Option 04 -- Fan (G) on with W output

Option 10 -- Reversing valve

Option 13 -- Room air temperature offset

Option 21 -- Keypad Lockout

With OF selected, the keypad cannot be locked. With ON selected

the keypad will be locked and can be unlocked by simultaneously

pressing the UP and DOWN keys for 5 seconds. Once unlocked, it

will relock 2 minutes after the last keypad press. If any key is

pressed and the thermostat is locked, “loc” will be displayed in the

clock digits.

Option 26 -- Minimum Cooling Setpoint

Option 27 -- Maximum Heating Setpoint

To Enter The Configuration Mode:

Option 26 -- Minimum Cooling Setpoint

Selections: 50_ to 90_F/10_ to 32_C — Default is 52_F/11_C.

Sets the lowest cooling setpoint available to the user.

Option 27 -- Maximum Heating Setpoint

Press and hold the FAN key for about 10 seconds until the display

changes so that only two pairs of digits are showing. The

configuration number, now 01, will appear in the

setpoint/temperature location and the configuration setting will

appear in the clock location. The configuration number (left pair)

will be flashing which means it can be adjusted using the UP and

DOWN keys. To cause the opposite pair to flash (to be adjustable),

press the H/C key. Successive presses of the H/C key alternate

between the configuration number (left) and the configuration

setting (right). To exit the configuration mode, press the

HOLD/END key. If no key is pressed for 3 minutes, the

configuration mode will automatically exit, returning the

thermostat to normal operation.

Selections: 50_ to 90_F/10_ to 32_C — Default is 88_F/31_C.

Sets the highest heating setpoint available to the user.

Step 4 — Understand Thermostat Operation

Temperature Display

Thermostat will display room temperature until UP or DOWN

button is pressed. The words SET TEMP appear when these

buttons are pressed and the current setpoint is displayed. If no

buttons are pressed for 5 sec, the display will change back to show

room temperature.

Back lighting

Configuration Options -- Selection:

Option 01 -- Equipment type

Continuous back -- lighting is not available. The backlight will come

on for 10 seconds after any button press. Without AC power and

when the battery is low, the backlight will remain off with button

presses.

Selections: with HP thermostat: HP, AC, PH, or PC

with AC thermostat: AC or PC

Meanings:

Battery Indicator

A battery indication icon on the display shows nothing, half, or

low/no battery condition. If the battery is full or operation is from

AC power, no icon appears. Under battery operation, if the battery

is half full, a half full battery icon appears. As the battery depletes

below half, the icon remains at half, but the 10 second backlight

disappears. When the battery is absent or depleted, the display goes

blank except for an empty battery icon and all outputs are turned

off.

PH or PC selects PTAC units (Packaged Terminal Air

Conditioners) which are used in motel rooms and other rented

spaces. When this option is selected, the display shows only the

setpoint, not the room temperature. Also, the compressor

timeguard is disabled, allowing the compressor to turn on

immediately when a demand is established.

HP or PH controls 1 speed heat pump with 1 stage of aux heat.

AC or PC controls 1 speed air conditioner with one stage of heat.

Timeguard Timer

Note that this option allows a HP thermostat to be converted to

control an AC system.

A 5 -- minute timeguard is built into the thermostat immediately

upon power up, and any time the compressor turns off. The

compressor will not turn on until the timeguard has expired. The

timeguard affects only compressor operation. Pressing UP and

FAN buttons simultaneously will override the timeguard for 1

cycle. If PTAC operation (PH or PC) is selected under Option 1,

the timeguard timer is eliminated.

Option 03 -- Fahrenheit/Centigrade

Selections: F = Fahrenheit — This is default.

C = Centigrade.

Selects temperature display units.

Option 04 -- Fan (G) ON with W output

Selections: OF = G not energized with W — This is default.

ON = G energized with W.

This selection determines whether the fan (G) is to be ON or OFF

when the W (furnace or strip heat) is ON. Furnaces and fan coils

which manage their own blowers do not require a separate G

Cycle Timer

In normal heating and cooling operation the thermostat will not

allow more than 4 equipment cycles per hour (or 1 cycle every 15

minutes). Both the Y and W outputs have a 15 -- minute timer that

starts counting down when the output is turned on, (e.g., if Y

output is turned on for 9 minutes and then satisfies, it cannot turn

back on for another 6 minutes regardless of demand). However,

pressing UP and FAN buttons simultaneously or changing the

setpoint will override the timer for 1 cycle.

Minimum on Timer

If the internal non -- volatile memory fails, E4 will alternately flash

with the temperature on the display and all heating and cooling

outputs will be turned off. The thermostat must be replaced.

Once the equipment has turned on, it will remain on for a

minimum of 3 minutes regardless of demand. However, the

equipment can turn off in less than 3 minutes if a change in

setpoint, or a change in mode occurs.

Step 5 — Check Thermostat Operation

Fan Operation

. Press FAN button. This will start continuous fan operation.

FAN ON icon will turn on.

. Press FAN button again. This will stop continuous fan oper-

ation. FAN ON icon will turn off.

Staging Timer

If the thermostat is a heat pump model, it has 2 -- stage heat

capability. In normal operation there is a 15 -- minute delay between

the first and second stages of heat. The Y output will energize first,

then 15 minutes later, W is allowed to come on if the thermostat

determines it is not satisfying the demand.

However, if the heating demand is greater than 5_F/3_C, there will

be only a 30 second delay before bringing on W.

Heating Operation

. Press H/C button until HEAT is displayed.

2. Press UP button until LCD readout reads 3_F/2_C above

room temperature. Press UP and FAN buttons simultan-

eously to defeat timers. Heating system should begin to op-

erate immediately.

Auxiliary Heat Indicator

. For HP thermostats only, press H/C button until EMHT

emergency heat) appears. Press UP and FAN buttons sim-

When operating a heat pump and either auxiliary heat or

emergency heat is active, an LCD display icon indicates this

condition.

(

ultaneously to defeat timers. Emergency heating (W is ON,

Y is OFF) should begin immediately.

Cooling Operation

. Press H/C button until COOL is displayed.

. Press DOWN button until LCD readout reads 3_F/2_C be-

low room temperature. Press UP and FAN buttons simultan-

eously to defeat timers. Cooling system should begin to op-

erate immediately.

Table 1 shows the thermostat outputs for each available stage of

heating or cooling. It may be useful in checkout or

troubleshooting.

A07821

Error Messages

If the room temperature sensor fails, two dashes ( -- -- ) will appear in

the temperature display and all heating and cooling outputs will be

turned off. The thermostat must be replaced.

Table 1 – Outputs

EQUIPMENT

CONFIGURATION

OPTION #1

THERMOSTAT

TYPE

CONFIGURATION

COOL

STAGE 1

HEAT

STAGE 1

HEAT

STAGE 2

EM HEAT

AC, PC

AC, HP

Y, G

--- ---

HP, PH

RVS = C

Y, G, O / B

Y, G

Y, G, W

HP, PH

RVS = H

Y, G, O / B

Y, G, W, O / B

WIRING DIAGRAMS

A06566

A06567

Fig. 1 -- A/C Thermostat Typical Installation

Fig. 2 -- HP Thermostat Typical Installation

Printed in U.S.A.

Edition Date: 05/09

C a t a l o g N o : T B --- PA C --- 7 S I

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

R e p l a ce s: TB --- PA C --- 6 SI

T B --- PA C

T B --- P H P

Base Series Programmable Thermostats

Homeowner’s Guide

MANUAL OPERATION

To Operate Manually (Without the Programmed

Comfort Schedule):

Designed and Assembled

in the USA.

Press the HOLD/END button to make the HOLD icon appear.

Then follow the four steps below:

. To Select the Mode:

Use the H/C button to move between the choices. OFF,

HEAT, COOL, or EMHT will appear on the display. EMHT

will only appear on heat pump models.

. To Select the Fan Operation:

Use the FAN button to move between continuous fan (in-

dicated by the FAN ON icon) and auto fan operation.

. To Read the Room Temperature:

The large display reads room temperature until a button is

pressed.

. To Adjust the Setpoint:

In normal operation, the large display shows room temper-

ature. At the first press of the UP or DOWN button, the

large display shows the current setpoint and the SET TEMP

icon is turned on. Further presses of the UP or DOWN but-

ton adjust the setpoint upward or downward. Five seconds

after the last button press, the display returns to the room

temperature and the SET TEMP icon turns off.

A07107

Base Series Programmable Thermostat

SETTING TIME AND DAY

At Power Up

When power is first applied, AC or HP will appear for 5 seconds to

tell you it is an air conditioner (AC) or a heat pump (HP) model.

After this, the time display will flash to tell you the power has been

off.

PROGRAMMED OPERATION

Introduction

The Base Series Programmable Thermostat provides four periods

per day (MORNING, DAY, EVE, NIGHT) and two schedules per

week (MoTuWeThFr and SaSu). A separate time, heat setpoint,

and cool setpoint can be set for each period and schedule. Before

starting to actually program the thermostat, fill out Table 1 with the

values you wish to program. (The Energy Starr, US Department of

Energy recommended time and temperature values are already

programmed for you as a starting point and are shown on the left

side of the table.)

Setting The Current Time:

. Press the TIME/TEMP button. SET TIME flashes on the

display.

. Press the UP or DOWN button until the correct time is dis-

played.

. To quickly advance to the proper time, press and hold the

UP or DOWN button.

. When the correct time appears on the display, press the

HOLD/END button.

The first press of the PROGRAM button brings up the

programming mode and places you at morning of the current day

and period. Successive presses move you between the four daily

periods.

NOTE: If you choose not to press the HOLD/END button, the

thermostat will automatically exit the time setting mode after 10

seconds.

While Programming:

The TIME/TEMP button moves between three selections of SET

TIME, SET TEMP & HEAT, and SET TEMP & COOL. These

three numbers are to be programmed for each of the periods

MORNING, DAY, EVE, and NIGHT.

Setting The Current Day:

. Press the DAY button to advance to the correct day.

. When the correct day appears on the display, press the

HOLD/END button.

The DAY button moves between the weekdays, (MoTuWeThFr)

and the weekend (SaSu) selections. A different schedule may be set

for the weekdays and the weekend. You may exit programming at

any time by pressing the HOLD/END button.

settings to the programmed comfort schedule. Pressing

HOLD/END will not alter your programmed comfort schedule.

Programming A Weekly Comfort Schedule:

. Press the PROGRAM button. The word PROGRAMMING

appears on the display and the words SET TIME flash on

the display. MoTuWeThFr or SaSu and the morning period

icons will appear on the display. The current mode (HEAT

or COOL) will also show. Use the DAY button to select

weekdays and the PROGRAM button to select MORNING.

Method 2 — Temporary Override

At the first press of the UP or DOWN button, the current

temperature setting will appear on the display. Pressing the UP or

DOWN button again will temporarily change the setpoint as

needed. At the next programmed time, the programmed comfort

schedule will resume.

. Press the UP or DOWN button to set the start time for

MORNING ( 1) value in Table 1).

CHANGING BATTERIES

. Press the TIME/TEMP button until COOL is on and SET

TEMP flashes on the display.

. Press the UP or DOWN button to select the cooling temper-

ature setpoint ( 2) value in Table 1).

. Press the TIME/TEMP button until HEAT is on and SET

TEMP flashes on the display.

. Press the UP or DOWN buttons to select the heating tem-

perature setpoint ( 3) value in Table 1).

In some situations, two AA batteries are the power source for the

thermostat. If batteries are used with your equipment then they

should last about one year. As the batteries lose their power a

battery icon appears on the display. As the batteries get weaker, the

icon goes down to one black bar and then none. As the icon

becomes empty, you will begin to lose thermostat functions

because the batteries are losing their power. When the batteries are

completely dead, you won’t be able to use the thermostat.

When using batteries for power, we recommend you replace them

with two AA alkaline batteries. They are in a compartment under

the lid on top of the thermostat. You do not have to remove the

thermostat from the wall to replace the batteries. Simply open the

lid, lift out the batteries, and replace them like you would any other

battery operated device.

. Press the PROGRAM button to advance to the next time

period. Enter time and temperature settings ( 4) through 12

in Table 1) for the periods DAY, EVE, and NIGHT by fol-

lowing items 2 -- 6 above.

. Press the DAY button to change between weekday and

weekend programming. To set the weekend schedule, repeat

items 2 through 7, entering values in 13) through 24) in

Table 1.

TROUBLESHOOTING

What if AUX HEAT appears on the display?

. Press END/HOLD to exit the programming mode.

(Heat pump model only)

Modifying Your Weekly Comfort Schedule

If you choose to change any of your weekly schedule, press

PROGRAM at any time. You will enter the programming schedule

at the present day, present mode, but always in the morning period.

You are ready to set the new starting time for the morning period.

One press of the TIME/TEMP button and you are ready to set the

new morning temperature. To set values for other periods, use the

PROGRAM button. To set values for other days, use the DAY

button. Press HOLD/END and you are finished.

If auxiliary heat is on, you will see AUX HEAT indicator in the

display. When it is on this means the system has determined that

it’s too cold outside for your heat pump to heat the house without

help, so it’s getting help from the electric heaters. This happens

automatically.

NOTE: This indicator does not mean there is a problem with your

system.

What if E -- Heat appears on the display?

If the heat pump is not working properly, you can manually turn

on the emergency heat for extra help in heating. You’ll know

there’s a problem if the house can’t seem to get warm when it’s

cold outside.

Overriding Your Comfort Schedule

There are two ways to override your comfort schedule.

Method 1 — Manual Operation

By pressing the HOLD/END button to turn on the HOLD icon, the

thermostat will maintain the current temperature settings and

ignore the comfort schedule for an indefinite period of time. The

word HOLD will appear in the display. Press the HOLD/END

button a second time and the thermostat will return the temperature

You want to avoid using emergency heat, though, because it’s the

most expensive option. And, of course, if you suspect a problem

with your heat pump, call your heating and cooling dealer

immediately.

Table 1 – Programming Table

ENERGY STAR

FACTORY DEFAULT VALUES

NEW COMFORT SCHEDULE

MoTuWe ThFr

TIME

SaSu

PERIOD

MORNING

DAY

TIME

COOL

HEAT

COOL

HEAT

COOL

14)

HEAT

15)

TIME

6:00

78_F

26_C

68_F

20_C

13)

A.M.

:00

A.M.

:00

P. M .

85_F

29_C

60_F

16_C

16)

19)

22)

17)

20)

23)

18)

21)

24)

78_F

26_C

68_F

20_C

EVE

0:00

82_F

28_C

60_F

16_C

NIGHT

10)

11)

12)

P. M .

CARRIER CORPORATION

Limited Warranty for Thermostats, User Interfaces, Zoning and Related Accessories

FOR WARRANTY SERVICE OR REPAIR:

Contact the installer or a Carrier dealer. You may find the installer’s name on the equipment or in your Owner’s Packet. You can also find a

Carrier dealer online at www.carrier.com.

For help, contact: Carrier Corporation, Consumer Relations, P.O. Box 4808, Syracuse, New York 13221 Phone: 1 -- 800 -- 227 -- 7437

PRODUCT REGISTRATION: You can register your product online at www.carrier.com.

Model No./Serial No._____________________________________ Series (Infinity, Performance, Comfort, Base,) __________________

Date of Installation ______________________________________ Installed by ____________________________________________

Name of Owner _________________________________________ Address of Installation ___________________________________

Carrier Corporation (hereinafter “Company”) warrants this product against failure due to defect in materials or workmanship under normal

use and maintenance as follows. All warranty periods begin on the date of original installation. If a part fails due to defect during the

applicable warranty period Company will provide a new or remanufactured part, at Company’s option, to replace the failed defective part at

no charge for the part. Alternatively, and at its option, the Company will allow a credit in the amount of the then factory selling price for a

new equivalent part toward the retail purchase price of a new Company product. Except as otherwise stated herein, those are Company’s

exclusive obligations under this warranty for a product failure. This limited warranty is subject to all provisions, conditions, limitations and

exclusions listed below and on the reverse (if any) of this document.

OWNER -- OCCUPIED, RESIDENTIAL APPLICATIONS

This warranty is to the original purchasing owner and is transferable only to the extent and as stated in the Warranty Conditions and below.

The warranty period in years, depending on the part and the claimant, is as shown in the chart below.

Limited Warranty (Years)

Series

Item

User Interface & Smart Sensor

Zoning Board

Original Owner

10* (or 5)

Subsequent Owner

10** (or 5)

Infinity

Network Interface

Remote Access

Thermostat***

Performance

Zoning Interface & Smart Sensor

Zoning System

Thermostat

Comfort

Base

Zoning Board

Thermostat

If properly registered within 90 days, otherwise 5 years (except in California and Quebec and other jurisdictions that prohibit warranty benefits condi-

tioned on registration, registration is not required to obtain longer warranty periods). See Warranty Conditions below.

* If properly transferred within 90 days, otherwise 5 years. See Warranty Conditions below. In California and Quebec and other jurisdictions that pro-

hibit warranty benefits conditioned on registration, registration is not required for a transfer and all warranty periods for subsequent owners are five

years from original installation.

** Applies only to Thermostats. Active electronic finished good accessories, such as the optional ExP module, have different warranty terms. See

product for details.

OTHER RESIDENTIAL APPLICATIONS (Apartments, Rental Properties, etc.)

The warranty period is five (5) years and is not transferable.

OTHER APPLICATIONS

This warranty is non -- transferable. The warranty period is one (1) year on all such applications.

LEGAL REMEDIES: The owner must notify the Company in writing, by certified or registered letter to Carrier Corporation, Warranty

Claims, P.O. Box 4808, Syracuse, New York 13221, of any defect or complaint with the product, stating the defect or complaint and a specific

request for repair, replacement, or other correction of the product under warranty, mailed at least thirty (30) days before pursuing any legal

rights or remedies.

9004DP110

5/09

CARRIER CORPORATION

WARRANTY CONDITIONS:

. To obtain the longer warranty periods as shown in the table under original owner, for the original purchaser, the product must be

properly registered at www.carrier.com within ninety (90) days of original installation. In jurisdictions where warranty terms condi-

tioned on registration are prohibited by law, registration is not required and the longer warranty period shown will be apply.

. Where a product is installed in a newly constructed home, the date of installation is the date the homeowner purchased the home from

the builder.

. If the date of original installation cannot be verified, then the warranty period begins ninety (90) days from the date of product manu-

facture (as indicated by the model and serial number). Proof of purchase may be required at time of service.

. The remainder of the first five years of warranty is freely transferable without registration. To obtain a transfer of the longer warranty

periods as shown in the table under subsequent owner, a subsequent owner must register the transfer at www.carrier.com within 90

days of the change in ownership and payment of a transfer fee. Not applicable in all jurisdictions. See website for details.

. Product must be installed properly and by a licensed HVAC technician.

. The warranty applies only to products remaining in their original installation location.

. Installation, use, care, and maintenance must be normal and in accordance with instructions contained in the Installation Instructions,

Owner’s Manual and Company’s service information.

. Defective parts must be returned to the distributor through a registered servicing dealer for credit.

LIMITATIONS OF WARRANTIES: ALL IMPLIED WARRANTIES AND/OR CONDITIONS (INCLUDING IMPLIED

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR USE OR PURPOSE) ARE

LIMITED TO THE DURATION OF THIS LIMITED WARRANTY. SOME STATES OR PROVINCES DO NOT ALLOW

LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY OR CONDITION LASTS, SO THE ABOVE MAY NOT APPLY TO

YOU. THE EXPRESS WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED,

ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.

THIS WARRANTY DOES NOT COVER:

. Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of either defective parts,

or replacement parts, or new units.

. Any product purchased over the Internet.

. Normal maintenance as outlined in the installation and servicing instructions or Owner’s Manual, including filter cleaning and/or re-

placement and lubrication.

. Failure, damage or repairs due to faulty installation, misapplication, abuse, improper servicing, unauthorized alteration or improper

operation.

. Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the inadequacy or interruption of

electrical service.

. Failure or damage due to floods, winds, fires, lightning, accidents, corrosive environments (rust, etc) or other conditions beyond the

control of Company.

. Parts not supplied or designated by Company, or damages resulting from their use.

. Products installed outside the U.S.A. or its territories and Canada.

. Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever, including additional or unusual use of

supplemental electric heat.

0. Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

1. ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY NATURE

WHATSOEVER. Some states or provinces do not allow the exclusion of incidental or consequential damages, so the above limitation

may not apply to you.

This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

9004DP110

5/09

Printed in U.S.A.

Edition Date: 05/09

C a t a l o g N o : T B --- PA C --- 7 S I

Manufacturer reserves the right to change, at any time, specifications and designs without notice and without obligations.

R e p l a ce s: TB --- PA C --- 6 SI

Lux Products RS4000 Thermostat User Manual

Honeywell L7248A,C,L Thermostat User Manual

Hunter Fan CM12 Thermostat User Manual1671

Lux Products PSDFC150 Thermostat User Manual

Honeywell TB7220 Thermostat User Manual

White Rodgers 1A66W Thermostat User Manual

Lux Products PSDFC159 Thermostat User Manual

Carrier 33CSIRRCVR 01 Thermostat User Manual

Honeywell CT1800 Thermostat User Manual

Bryant OM 17 101 Thermostat User Manual