Home

href="
Blue Universal Thermostat with  
Automatic Heat/Cool Changeover Option  
Single Stage, Multi-Stage or Heat Pump  
Installation and Operating Instructions for Models:  
Save these instructions for future use!  
Model  
Programming Choices  
FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS  
CAREFULLY BEFORE INSTALLING OR OPERATING  
THIS CONTROL COULD CAUSE PERSONAL INJURY  
AND/OR PROPERTY DAMAGE.  
5+1+1 Day 5+2 Day Non-Programmable  
Non-Programmable  
1F85-0422  
1F83-0422  
APPLICATIONS  
THERMOSTAT APPLICATION GUIDE  
1F83-0422 Thermostat  
Description  
Heat Pump (No Aux. or Emergency Heat)  
Heat Pump (with Aux. or Emergency Heat)  
Systems with up to 2 Stages Heat, 2 Stages Cool  
Heat Only Systems (with optional fan switch)  
Millivolt Heat Only Systems – Floor or Wall Furnaces  
Cool Only Systems  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Yes  
Gas or Oil Heat  
Electric Furnace  
Hydronic (Hot Water) Zone Heat – 2 Wires  
Hydronic (Hot Water) Zone Heat – 3 Wires  
SPECIFICATIONS  
Electrical Rating:  
Battery Power.................................................... mV to 30 VAC, NEC Class II, 50/60 Hz or DC  
Input-Hardwire................................................... 20 to 30 VAC  
Terminal Load........................................................... 1.5 A per terminal, 2.5A maximum all terminals combined  
Setpoint Range......................................................... 45° to 90°F (7° to 32°C)  
Rated Differentials:  
Fast  
Med.  
0.6 °F  
1.2 °F  
1.2 °F  
Slow  
Heat (SS1, MS2) ............................................... 0.4 °F  
Cool (SS1, MS2)................................................ 0.9 °F  
Heat Pump (HP1, HP2) ..................................... 0.9 °F  
Emer (HP1, HP2)............................................... 0.6 °F  
1.7 °F  
1.7 °F  
1.7 °F  
1.7 °F  
Operating Ambient.................................................... 32° to +105°F (0° to +41°C)  
Operating Humidity................................................... 90% non-condensing max.  
Shipping Temperature Range ................................... -40° to +150°F (-40° to +65°C)  
Dimensions Thermostat............................................ 3-7/8”H x 5-1/8”W x 1-1/4”D  
ATTENTION: MERCURY NOTICE  
This product does not contain mercury. However, this  
product may replace a product that contains mercury.  
CAUTION  
To prevent electrical shock and/or equipment damage,  
disconnect electric power to system at main fuse or  
circuit breaker box until installation is complete.  
!
Mercury and products containing mercury must not be  
discarded in household trash. Do not touch any spilled  
mercury. Wearing non-absorbent gloves, clean up any  
spilled mercury and place in a sealed container. For prop-  
er disposal of a product containing mercury or a sealed  
container of spilled mercury, place it in a suitable shipping  
container. Refer to www.thermostat-recycle.org for loca-  
tion to send product containing mercury.  
Index  
Page  
Installation  
2
2
3
4
6
7
8
Wiring Connections  
Thermostat Quick Reference  
Installer Configuration Menu  
Operating Your Thermostat  
Programming  
Troubleshooting  
PART NO. 37-7240B  
Replaces 37-7240A  
1316  
href="
INSTALLATION  
Figure 1 – Battery door shown open  
WARNING  
Thermostat installation and all components of the  
control system shall conform to Class II circuits per  
the NEC code.  
!
“AA” Alkaline Batteries  
Remove Old Thermostat  
A standard heat/cool thermostat consists of three basic parts:  
1) The cover, which may be either a snap-on or hinge type.  
2) The base, which is removed by loosening all captive  
screws.  
3) The switching subbase, which is removed by unscrewing  
the mounting screws that hold it on the wall or adapter  
plate. Before removing wires from old thermostat,  
label each wire with the terminal designation from  
which it was attached. Disconnect the wires from the  
old thermostat one at a time. Do not let wires fall back  
into the wall.  
Thermostat can be powered by system AC power or Battery.  
If  
is displayed, the thermostat is battery powered. If  
is not displayed, thermostat is system powered with optional  
battery back-up. When battery power remaining is approxi-  
mately half, the  
will be displayed. When “Change  
is displayed, install fresh “AA” alkaline batteries immediately.  
For best results, replace all batteries with new premium brand  
alkaline batteries such as Duracell® or Energizer®. We recom-  
mend replacing batteries every 2 years. If the home is going  
to be unoccupied for an extended period (over 3 months) and  
is displayed, the batteries should be replaced before  
leaving. When less than two months of battery life remain, the  
setpoint temperature will offset by 10 degrees (10 degrees  
cooler in Heat mode / 10 degrees warmer in Cool mode). If  
offset occurs, the normal setpoint can be manually reset with  
Installing New Thermostat  
1) Pull the thermostat body off the thermostat base. Forcing  
or prying on the thermostat will cause damage to the unit.  
2) Place base over hole in wall and mark mounting hole  
locations on wall using base as a template.  
or  
. Another offset will occur within two days if batter-  
3) Move base out of the way. Drill mounting holes. If you  
are using existing mounting holes and the holes drilled  
are too large and do not allow you to tighten base snugly,  
use plastic screw anchors to secure the base.  
ies are not replaced.  
Figure 2 – Thermostat base and rear view of thermostat  
4) Fasten base snugly to wall using mounting holes shown  
in Figure 2 and two mounting screws. Leveling is for  
appearance only and will not affect thermostat operation.  
5) Connect wires to terminal block on base.  
6) Push excess wire into wall and plug hole with a fire re-  
sistant material (such as fiberglass insulation) to prevent  
drafts from affecting thermostat operation.  
Mounting  
Hole  
Mounting  
Hole  
Place Level  
Place Level  
across  
Mounting Tabs  
across  
Mounting Tabs  
(for appearance only)  
7) Carefully line the thermostat up with the base and snap  
into place.  
(for appearance only)  
Batteries  
2 “AA” alkaline batteries are included with the thermostat.  
To install the batteries, pull the battery door as shown by the  
arrow and lift open. Using the polarity indicated inside the bat-  
tery door, insert the batteries. To close the battery door, swing  
the door down while pulling in the direction of arrow. Once  
fully down, snap the door back into position. To replace the  
batteries, set system to OFF.  
WIRING CONNECTIONS  
Refer to equipment manufacturers’ instructions for specific Refer to 37-6895 for 1F83-0422/1F85-0422 wiring diagram  
system wiring information. After wiring, see CONFIGURATION specifications.  
section for proper thermostat configuration.  
TERMINAL DESIGNATION DESCRIPTIONS  
Terminal  
Terminal  
Designation  
Description  
Designation Description  
L...............Heat pump malfunction indicator for systems  
with malfunction connection  
W/E............Heat Relay/Emergency Heat Relay (Stage 1)  
W2.............2nd Stage Heat (HP 1)  
O..............Changeover valve for heat pump energized  
constantly in cooling  
G..............Fan Relay  
RH.............Power for Heating  
B ..............Changeover valve for heat pump energized  
constantly in heating  
Y ..............Compressor Relay  
RC.............Power for Cooling  
C ..............Common wire from secondary side of cooling system  
transformer or heat only system transformer  
6...............3 Wire Zone Valve – Energized when no call for Heat  
Y2 .............2nd Stage Compressor  
2
href="
THERMOSTAT QUICK REFERENCE  
Home Screen Description  
Figure 3 – Home Screen Display  
Setting  
Room  
Time of day (1F85 only)  
Temperature  
Temperature  
Mo  
Set  
P
Displays the power level of  
the 2 “AA” batteries:  
indicates good power level  
indicates batteries at about  
half power. “Change  
” indicates  
batteries are low and should be  
replaced with 2 new premium brand  
“AA” Alkaline batteries.  
(See page 2 for more details)  
SYSTEM  
Heat  
FAN  
Auto  
Menu  
System  
Indicator  
Fan  
Indicator  
Figure 4 – Programming & Configuration Items  
13  
2
4
14  
Mo Tu We Th Fr Sa Su  
P Date  
Temp Hold  
Set  
12  
8
Save  
Month Call For Service  
Year  
Change  
Filter  
System On  
Heat Pump  
SYSTEM  
Heat Emer Auto  
Cool Oꢀ Time  
3
9
10  
11  
Hold  
1
2
Auto Sched  
Cool Savings  
FAN  
On Auto  
Run Sched  
Run  
Schedule  
Menu  
6
7
5
Displays “Save” when Cool SavingsTM is working.  
Programming and Configuration Items  
8
“System On” indicates when heating or cooling stage  
is energized, “+2” flashing indicates when a second  
stage is energized.  
Displays “Heat Pump” when system is configured  
as Heat Pump thermostat.  
1
2
3
9
Displays “Hold” in programmable mode when not in  
“Hold” mode. Displays Light Bulb in non-programmable  
mode.  
10  
The word HOLD is displayed when the thermostat is in  
the HOLD mode. Temp HOLD is displayed when  
the thermostat is in a Temporary HOLD mode.  
Initially displays “Auto Sched”. If Auto Schedule had  
been used or disabled, then it displays “Cool Savings”  
when in the Cool Mode if Cool Savings has been ena-  
bled in the menu.  
11  
Displays Change Filter when the system has run for  
the programmed filter time period as a reminder to  
change or clean your filter.  
Displays “Set” for setpoint when in Run Program mode.  
4
“Call For Service” indicates a fault in the heating/  
cooling system, it does not indicate a fault in the  
thermostat.  
12  
Displays System Mode (Heat, Emer, Auto, Cool, Off)  
or Time in menu mode.  
5
Alternates Time of Day and “LOC” when keypad lockout  
Displays Fan Mode (On, Auto) or “Run Sched” in  
13  
6
is enabled.  
Menu mode.  
7
In Configuration Menu, shows screen number. If blank,  
thermostat is earlier model and requires instruction sheet  
Displays “Run Schedule”, “Schedule”, or “Menu”.  
14  
37-7136A.  
3
href="
INSTALLER/CONFIGURATION MENU  
To enter the Configuration Menu, SYSTEM must be set to HEAT, COOL, EMER or AUTO. With thermostat in Heat, Cool or  
Auto, in normal operation, press the Menu button for at least 5 seconds. The display will show item #1 in the table below. Press  
Menu to advance to the next menu, Press  
or  
to change an item option. Shaded items are not available to 1F83.  
INSTALLER/CONFIGURATION MENU  
MENU  
SCREEN #  
MS/  
DISPLAYED  
Press  
or  
to  
SS (FACTORY DEFAULT)  
COMMENTS  
select from listed options  
1F85 1F83 HP  
01 01  
(OFF) Lk  
L
Selects Keypad Lockout.  
(Not available on earlier models, see 37-6894D)  
Selects Keypad lockout combination number  
02 02  
03 03  
(000) Lk  
(MS 2)  
001 to 999  
HP 1, SS 1  
Selects Multi-Stage (MS 2 No Heat Pump),  
Heat Pump 1 (HP 1, 1 compressor),  
or Single Stage (SS 1)  
04 04  
05 05  
(GAS)  
(ELE)  
(0)  
CS  
(On)  
E
(ME)  
CR Heat  
(ME)  
CR Cool  
(ME)  
ELE  
GAS  
1, 2, 4, 5, 6  
Select Gas or Electric heat  
Selects Cool Savings  
Value 1 (low) to 6 (high), Value 0 Disables Feature  
Selects Energy Management Recovery (EMR)  
On or OFF. 1F85 only  
06  
OFF  
07 06  
08 07  
09 08  
10 09  
SL, FA  
SL, FA  
SL, FA  
Adjustable Anticipation:  
Selects heating cycle rate for MS or SS  
Adjustable Anticipation: Selects the cycle rate for  
cooling (only when MS2 or SS1 is selected in item 1)  
Adjustable Anticipation (Heat Pump)  
(only when heat pump is selected in #1)  
Selects the cycle rate for Emergency mode and  
Auxiliary stage if Heat Pump is selected in item 1)  
Compressor Lockout Time  
CR Heat Pump  
(FA)  
SL  
CR Emer  
(OFF) CL  
11 10  
12 11  
CL On  
Heat-Auto-Cool-Off  
Auto-Off, Cool-Off,  
Heat-Off without Fan,  
Heat-Off Heat-Cool-Off  
dL OFF  
Selects System Mode Configuration  
13 12  
14 13  
(On) dL  
0
Selects Display Light On or OFF  
Adjustable Ambient Temperature Display  
1 HI, 2 HI, 3 HI, 4 HI,  
(current temperature) 1 LO, 2 LO, 3 LO, 4 LO  
15 14  
Selects Fahrenheit/Celsius Temperature Display  
°F  
°C  
15  
16  
16  
17  
18  
L (90) Heat  
L (45) Cool  
P3  
L 62 to L 89  
L 46 to L 82  
P0, P2  
Selects Limited HEAT Range  
Selects Limited COOL Range  
Defaults for 5+1+1 programming (P3) but non-  
programmable (PO) or 5+2 programming (P2)  
is available on most models. 1F85 only  
Automatic Schedule for heat mode. 1F85 only.  
NA to Cool only system.  
19  
20  
(On) AS Heat  
(On) AS Cool  
(On) FA Heat  
(On) FA Cool  
OFF  
OFF  
OFF  
OFF  
Automatic Schedule for cool mode. 1F85 only.  
NA to Heat only system.  
21 17  
22 18  
Fast Heat option may be disabled by selecting OFF.  
NA to SS config. NA to Cool only system.  
Fast Cool option may be disabled by  
selecting OFF. NA to SS config.  
NA to Heat only system.  
23 19  
(OFF) CA  
(On) dS  
Selects active Comfort Alert On or OFF.  
Require CA II Module. (Not available on earlier models)  
Selects Automatic daylight Savings Time option  
On or OFF. 1F85 only  
On  
24  
OFF  
25 20  
26 21  
(OFF) Change Filter  
(200 h) Change Filter  
On  
25-1975 h  
Selects Filter Change-out Indicator On or OFF.  
Change Filter time in 25 hour increments. This  
menu only appears if On is selected in above.  
Selects operation of the reversing valve terminal  
(O/B) output as an O or B terminal.  
27 22  
(o) On Cool  
(b) On Heat  
4
href="
INSTALLER/CONFIGURATION MENU  
1 & 2)Keypad Lockout – This menu selection will display  
Lk” and “OFF” (default, keypad not locked out). The  
ment Recovery (E) On enables the thermostat to start  
heating or cooling early to make the building temperature  
reach the program setpoint at the time you specify. Heat-  
ing will start 5 minutes early for every 1° of temperature  
required to reach setpoint.  
Example: E On is selected and your heating is pro-  
grammed to 65° at night and 70° at 7 AM. If the build-  
ing temperature is 65°, the difference between 65° and  
70° is 5°. Allowing 5 minutes per degree, the thermostat  
setpoint will change to 70° at 6:35 AM. Cooling allows  
more time per degree, because it takes longer to reach  
set temperature.  
and  
are used to toggle the selection between  
OFF and “L(keypad locked out). When the keypad  
lockout selection is enabled L, and the MENU button  
is pressed again, the display will indicate the number  
“0” (default, still disabled) in the time digits. The  
and  
are used to set the combination number from 0  
to 999. If a combination of 0 is selected and the MENU  
button is pressed, the menu will be exited and keypad  
will not be locked. If 1 to 999 is selected and the MENU  
button is pressed, the combination is stored into memory  
and the menu is exited. The “LOC” will display designat-  
ing keypad locked with a valid combination. The SYSTEM  
button will operate for 10 seconds after the menu mode  
is exited to allow the user to change the mode from  
OFF” to the desired SYSTEM mode.  
7, 8, 9 & 10) Cycle Rate Selection – The factory default set-  
ting for Heat and Cool modes, SS1 and MS2 is medium  
cycle (ME). For Heat Pump and HP1, the default setting  
is medium (ME). For Emer (Aux) the default setting is fast  
cycle (FA). To change cycle rate, press the  
key.  
or  
While the keypad is locked out, a press of MENU will en-  
ter the configuration menu. The first menu item displayed  
Cycle rate differentials for different settings are:  
is the combination code “0”. The  
or  
keys are  
Fast  
FA  
Medium Slow  
used to set the combination unlock number from 0 to  
999. If the unlock number matches exactly with the com-  
bination lock number stored in memory when the MENU  
button is pressed, the keypad is unlocked and the “LOC”  
is removed. If the unlock number does not match when  
the MENU button is pressed, the combination returns to  
“0” for another attempt to set the unlock code. To exit the  
menu without unlocking the keypad, press RUN SCHED.  
MODE  
ME  
SL  
Heat (SS1, MS2)  
Cool (SS1, MS2)  
Heat Pump (HP1)  
Emer (HP1)  
0.4°F  
0.9°F  
0.9°F  
0.6°F  
0.6°F  
1.2°F  
1.2°F  
-
1.7°F  
1.7°F  
1.7°F  
1.7°F  
11) Select Compressor Lockout CL OFF or ON – Select-  
ing CL ON will cause the thermostat to wait 5 minutes  
between cooling cycles. This is intended to help protect  
the compressor from short cycling. Some newer com-  
pressors already have a time delay built in and do not  
require this feature.Your compressor manufacturer can  
tell you if the lockout feature is already present in their  
system. When the thermostat compressor time delay oc-  
curs, it will flash the setpoint for up to five minutes.  
12) System Mode Configuration – This thermostat is con-  
figured for Heat and Cool with Auto Changeover (SYS-  
TEM switch with Heat, Auto, Cool, Off). It can also be  
configured for Heat and Cool (Heat, Cool, Off), Heat only  
To reset the combination code and unlock the keypad if  
the code is forgotten, see troubleshooting section.  
3) This control can be configured for:  
MS 2 – Multi-Stage System (no heat pump)  
HP 1 – Heat Pump with one stage of compressor  
SS 1 – Single Stage System  
4) GAS or Electric (ELE) fan operation. If the heating sys-  
tem requires the thermostat to energize the fan, select  
ELE. Select GAS if the heating system energizes the fan  
on a call for heat.  
5) Select Cool Savings™ value – Selects the amount  
of adjustment for the Cool Savings™ feature in Cool  
mode with 1 (1°) being the least amount of adjustment  
and 6 (6°) being the most amount of adjustment. Default  
value is 0 which disables this feature. Cool Savings is  
an optional energy saving feature that can reduce your  
cooling costs. It is based on the principal that lower  
indoor humidity makes a slightly higher temperature  
feel more comfortable. Cool Savings operates during  
periods of high demand which normally occur on the  
hottest summer days when a cooling system may run  
for hours to reach the thermostat setting. Long cooling  
run times also lower the indoor humidity. Cool Savings,  
very slowly, adjusts the setpoint temperature to make the  
setpoint closer to the displayed room temperature, to a  
maximum of the number of degrees you select. Adjust-  
ing the setpoint temperature over a long cooling run time  
allows the system to reach your set temperature and turn  
off. The room temperature will actually be higher than  
the thermostat displays but the reduction in humidity will  
allow comfort at the slightly higher temperature.  
with Fan (Heat, Off, FAN Switch) Heat only without Fan  
(Heat, Off) Auto only (Auto, Off) and Cool only (Cool,  
Off).  
13) Select Backlight Display – The display backlight im-  
proves display contrast in low lighting conditions. When  
the “C” terminal is powered, selecting backlight CdL ON  
will keep the light on continuously. Select backlight OFF  
will turn the light on momentarily after any key is pressed.  
When the “C” terminal is not powered, the light will be on  
momentarily after any key is pressed no matter whether  
the backlight is selected ON or OFF.  
14) Select Temperature Display Adjustment 4 LO to 4 HI  
– Allows you to adjust the room temperature display up  
to 4° higher or lower.Your thermostat was accurately cali-  
brated at the factory, but you have the option to change  
the display temperature to match your previous thermo-  
stat. The current or adjusted room temperature will be  
displayed.  
15) Select F° or C° Readout – Changes the display readout  
to Celsius or Fahrenheit as required.  
To turn this feature on in the Cool mode press Cool  
Savings. The display will show “Save” next to the  
setpoint temperature. When Cool Savings is making ad-  
justments to the room temperature display “Save” will be  
flashing and the displayed room temperature may vary  
within the adjustment range you selected.  
If “Save” is not displayed and this feature is OFF, no  
change will occur when the cooling system is continu-  
ously running during periods of high demand.  
16) Limited Heat Range – This feature provides a maximum  
setpoint temperature for heat. The default setting is 90°F.  
It can be changed between 62°F and 89°F by pressing  
the  
or  
key.  
17) Limited Cool Range – This feature provide a minimum  
setpoint temperature for cool. The default setting is 45°F.  
It can be changed between 46°F and 82°F by pressing  
the  
or  
key.  
18) Program Options: 1F85 only, configured for 5+1+1 day  
or 5+2 day programming or non-programming mode. The  
default setting is P3, indicating 5+1+1 day programming.  
6) Energy Management Recovery: (this step is skipped if  
configured to be non-programmable). Energy Manage-  
5
href="
INSTALLER/CONFIGURATION MENU  
The programs per week can be changed to P2 or P0 by  
in Troubleshooting section.) If a Comfort Alert module is  
not connected, or to disable active protection, turn this  
feature OFF. If a Comfort Alert module is connected and  
this feature is turned OFF, the thermostat will still receive  
and flash the fault codes from the Comfort Alert module,  
but the active protection will not be enabled to protect the  
compressor.  
pressing the  
or  
keys. A selection of 0 Days for  
non-programmable will eliminate the need for EMR, and  
that step in the menu will be skipped.  
19 & 20) Select Automatic Schedule – 1F85 only, with just  
one touch of the Auto Schedule key this feature allows  
you to program a desired comfort temperature into all the  
24) Select Daylight Saving Time Calculation – 1F85 only,  
this feature will allow the thermostat to calculate the DST  
automatically and apply it to the Real Time Clock display.  
program periods along with a 6° set back for night peri-  
ods of both Heat and Cool programs. Factory default is  
“On” for both. When Heat AS On and Cool AS On are  
activated while in Heat or Cool mode, select desired  
setpoint temperature and press Auto Schedule. This  
value will be copied into all the morning, day and evening  
program periods. The night program periods will have a  
6°F set back.  
Default On. Use  
feature OFF.  
or  
touch keys to select the  
25 & 26) Select Filter Replacement Reminder and Set  
Run Time – Select the “Change Filter” reminder On  
or OFF. If selected On, press MENU to select the time  
period from 25 to 1975 hours in 25 hours increments.  
In a typical system, 200 hours (default) of run time is  
approximately 30 days. After the selected time of blower  
operation, the thermostat will display “Change Filter”  
as a reminder to change or clean your air filter. When  
“Change Filter” is displayed, press MENU or RUN  
SCHED button to clear the display and restart the time to  
the next filter change.  
21 & 22) Select Fast Second Stage ON or OFF – Heat  
pump or Multi-stage only, in the run mode, with the fast  
Heat feature enabled (FA Heat On), if the Heat setpoint  
temperature is manually raised by 3°F (2°C) or more  
above the actual temperature using  
the second  
stage will energize immediately. With FA OFF, second  
stage will not energize until the setpoint temperature is  
1°F or more above actual temperature for more than ten  
minutes. The Fast Cool feature (FA Cool) provides the  
same controls when the setpoint temperature is lowered.  
27) Select Reversing Valve Output – The O/B option is  
factory set at “O” position. This will accommodate the  
majority of heat pump applications, which require the  
23) Comfort Alert with Active Protection Turn this  
feature ON to enable active protection. This allows the  
thermostat to identify fault codes sent by the Comfort  
Alert module when compressor damage is possible and  
react to those codes by turning the compressor off. Fault  
codes from the Comfort Alert module will flash on the  
thermostat. (Refer to Comfort Alert Yellow Alert Codes  
changeover relay to be energized in COOL. If the  
thermostat you are replacing or the heat pump being  
installed with this thermostat requires a “B” terminal, to  
energize the changeover relay in HEAT, the O/B option  
should be set at “B” position.  
OPERATINGYOUR THERMOSTAT  
IMPORTANT!  
Choose the Fan Setting (Auto or On)  
Set the FAN Switch to Auto or On.  
Fan Auto is the most commonly selected setting and runs the  
fan only when the heating or cooling system is on.  
Fan On runs the fan continuously for increased air circulation  
or to allow additional air cleaning.  
Manual Operation for Non-Programmable  
Mode  
Press the SYSTEM button to select Heat or Cool and use  
the  
or  
buttons to adjust the temperature to your  
desired setting. After selecting your desired settings you can  
also press the SYSTEM button to select AUTO to allow the  
thermostat to automatically change between Heat and Cool.  
Choose the System Setting  
(Heat, Off, Cool, Auto, Emer)  
Press the SYSTEM button to select:  
Manual Operation (Bypassing the Program)  
Programmable Thermostats  
Press  
or  
and then the HOLD button and adjust the  
Heat: Thermostat controls only the heating system.  
Off: Heating and Cooling systems are off.  
temperature wherever you like. This will override the program.  
The HOLD feature bypasses the program and allows you  
to adjust the temperature manually, as needed. Whatever  
temperature you set in HOLD will be maintained 24 hours  
a day, until you manually change the temperature or press  
RUN SCHED to cancel HOLD and resume the programmed  
schedule.  
Cool: Thermostat controls only the cooling system.  
Auto: Auto Changeover is used in areas where both heating  
and cooling may be required on the same day. AUTO allows  
the thermostat to automatically select heating or cooling  
depending on the indoor temperature and the selected heat  
and cool temperatures. When using AUTO, be sure to set the  
Cooling temperatures more than 1° Fahrenheit higher than  
the heating temperature.  
Program Override (Temporary Override)  
Press  
or  
buttons to adjust the temperature. This  
Emer: (Heat Pump models) Thermostat controls only backup  
heating system.  
will override the temperature setting for four hours. To cancel  
the temporary setting at any time and return to the program,  
press Run Sched. If the SYSTEM button is pressed to select  
AUTO the thermostat will change to Heat or Cool, whichever  
ran last. If it switches to heat but you want cool, or it changes  
to cool but you want heat, press both  
and  
buttons  
simultaneously to change to the other mode.  
6
href="
OPERATINGYOUR THERMOSTAT  
IMPORTANT!  
delay second stage for a longer time if you manually raise  
the temperature or if the room temperature quickly changes.  
Once the second stage comes on, it will come on sooner the  
next time there is a difference between the setpoint and the  
room temperature. The net effect of the staging program is  
that when the first stage is capable of making temperature  
the second stage will delay longer. When the thermostat  
calculates that first stage cannot make temperature in a  
reasonable time, the second stage will come on sooner. This  
built in function automatically optimizes the use of additional  
stages of heat or cool.  
Second Stage Time Delay  
Your thermostat is designed to determine the optimum time  
to activate the second stage. Simply raising the temperature  
in heating or lowering it in cooling will not always force the  
thermostat to bring the second stage on quickly. There is a  
time delay from 0-30 minutes depending on the performance  
of the first stage of the system.  
EXAMPLE: For the last 2 hours the thermostat is set on 70°  
and the room temperature is 70° with the equipment using  
only the first stage of heat. Since the equipment is keeping  
the temperature within 1° of setpoint, the thermostat will  
PROGRAMMING (For Programmable Model Only)  
4) Press  
or  
key to change the temperature to your  
Set Current Time and Date  
selected temperature for the 1st heating period.  
5) Press TIME button, time will flash.  
6) Press  
1st period.  
7) The time will change in 15 minute increments.  
8) After you have set the time and the temperature for  
the period to begin, press SCHEDULE to advance to the  
next program period.  
9) Repeat steps 2 through 8 until all of the program times  
and temperatures are set for all program periods on that  
day.  
1) Press MENU and then TIME button once. The display  
will show the hour only.  
or  
key to adjust the start time for the  
2) Press and hold either the  
or  
key until you reach  
the correct hour and AM/PM designation (AM begins at  
midnight, PM begins at noon).  
3) Press TIME once again. The display window will show  
the minutes only.  
4) Press and hold either the  
the correct minutes.  
5) Additional presses of TIME will advance the display to  
show the year, month and date of month. Press the  
or  
key until you reach  
10) Press SCHEDULE to the next day and repeat steps 2  
through 9.  
or  
key to change the display to the correct setting  
for each.  
11) When programming is complete and all of the times and  
temperatures match your desired heating schedule, press  
RUN SCHEDULE. The thermostat will now run your  
program.  
6) Press RUN SCHED to exit the TIME mode.  
Enter the Heating Program  
1) Press SYSTEM button to select “Heat” in the system  
switch area indicating the active mode being pro-  
grammed.  
2) Press the MENU button and then press SCHEDULE.  
3) The top of the display will show the day(s) being pro-  
grammed. The time and temperature (flashing) are also  
displayed. “1” will also be displayed to indicate the period.  
Enter the Cooling Program  
1) Press SYSTEM button to select “Cool” in the system  
switch area indicating the active mode being pro-  
grammed.  
2) Follow Enter Heating Program instructions for entering  
cooling times and temperatures.  
Energy Saving Factory Pre-Program  
The 1F85-0422 thermostats are programmed with the energy  
saving settings shown in the table below for all days of the  
week. If this program suits your needs, simply set the thermo-  
stat clock and press the RUN SCHED button.  
The table below shows the factory set heating and cooling  
schedule for all days of the week.  
Wake Up  
(Period 1)  
Leave For Work Return Home  
(Period 2) (Period 3)  
Go To Bed  
(Period 4)  
Heating  
Program  
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F  
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F  
Cooling  
Program  
7
href="
PROGRAMMING  
PlanningYour Program – Important  
The Heating and Cooling Program schedules below allow you  
to pencil in your own program times and temperatures.  
The 1F85-0422 comes configured for 5+1+1 day program-  
ming and can also be configured for 5+2 day programming  
(see configuration section).  
If you are re-programming a 5+1+1 fill in all lines with the  
times and temperatures you want.  
Keep the following guidelines in mind when planning your  
program.  
• In Heating, lower temperatures will save energy.  
• In Cooling, higher temperatures will save energy.  
• If you plan on using Auto Changeover, do not program  
the heating higher than the cooling.  
Factory settings are listed on Monday through Friday, Satur-  
day and Sunday. If you are re-programming a 5+2 day sched-  
ule, pencil in your own times and temperatures directly below  
the factory times and temperatures.  
Worksheet for Re-Programming 5+2 Day and 5+1+1 Day Program  
Heating  
Program  
Wake Up  
(Period 1)  
Leave For Work Return Home  
(Period 2) (Period 3)  
Go To Bed  
(Period 4)  
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F  
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F  
6:00 AM 70°F 8:00 AM 62°F 5:00 PM 70°F 10:00 PM 62°F  
Mon-Fri  
Sat-Sun  
or Sat  
Sun  
5+1+1 only  
Cooling  
Program  
Wake Up  
(Period 1)  
Leave For Work Return Home  
(Period 2) (Period 3)  
Go To Bed  
(Period 4)  
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F  
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F  
6:00 AM 75°F 8:00 AM 83°F 5:00 PM 75°F 10:00 PM 78°F  
Mon-Fri  
Sat-Sun  
or Sat  
Sun  
5+1+1 only  
TROUBLESHOOTING  
Comfort Alert Codes  
Comfort AlertYellow Alert Codes  
The Comfort Alert diagnostics product monitors the air  
conditioning outdoor systems with single phase Copeland  
Scroll compressors. Abnormal system and electrical  
conditions are indicated by flashing ALERT codes on the  
yellow LED on the Comfort Alert module. The flash codes are  
transmitted to the thermostat by the Comfort Alert Thermostat  
interface module. The Comfort Alert compatible thermostat  
displays “Call For Service” that flashes at the same rate as  
the yellow LED on the Comfort Alert module.  
1 Flash  
Long run time  
System pressure trip  
Short cycling  
2 Flashs  
3 Flashs  
4 Flashs  
5 Flashs  
6 Flashs  
7 Flashs  
8 Flashs  
9 Flashs  
Locked rotor  
Open circuit  
Open start circuit  
Open run circuit  
Welded Contactor  
Low voltage  
8
href="
TROUBLESHOOTING  
Reset Operation  
function correctly contact your heating/cooling service person  
or place of purchase.  
Note: Be sure to review the installer configuration menu  
settings.  
Note: When thermostat is reset, installer configuration menu  
settings and programming will reset to factory settings.  
If a voltage spike or static discharge blanks out the display  
or causes erratic thermostat operation, you can reset the  
thermostat by removing the wires from terminals R and C  
(do not short them together) and removing batteries for 2  
minutes. After resetting the thermostat, replace the wires and  
batteries. If the thermostat has been reset and still does not  
To reset the programming, clock and configuration settings,  
press  
and  
and the FAN button simultaneously. The  
thermostat should go blank and then all segments will be  
displayed momentarily.  
Symptom  
Possible Cause  
Correction Action  
No Heat/No Cool/No Fan  
(common problems)  
1. Blown fuse or tripped circuit breaker.  
2. Furnace power switch to OFF.  
3. Furnace blower compartment door or  
panel loose or not properly installed.  
4. Loose connection to thermostat or  
system.  
Replace fuse or reset breaker.  
Turn switch to ON.  
Replace door panel in proper position to engage safety  
interlock or door switch.  
Tighten connections.  
No Heat  
1. Pilot light not lit.  
Re-light pilot.  
2. Furnace Lock-Out Condition. Heat  
may also be intermittent.  
Many furnaces have safety devices that shut down when  
a lock-out condition occurs. If the heat works intermittently  
contact the furnace manufacturer or local HVAC service  
person for assistance.  
3. Heating system requires service or  
thermostat requires replacement.  
Diagnostic: Set SYSTEM Switch to HEAT and raise the  
setpoint above room temperature. Within a few seconds  
the thermostat should make a soft click sound. This sound  
usually indicates the thermostat is operating properly. If  
the thermostat does not click, try the reset operation listed  
above. If the thermostat does not click after being reset  
contact your heating and cooling service person or place  
of purchase for a replacement. If the thermostat clicks,  
contact the furnace manufacturer or a HVAC service  
person to verify the heating is operating correctly.  
No Cool  
1. Cooling system requires service or  
thermostat requires replacement.  
Same as diagnostic for No Heat condition except set the  
thermostat to COOL and lower the setpoint below the room  
temperature. There may be up to a five minute delay before  
the thermostat clicks in Cooling.  
1. Possible short in wiring.  
2. Possible short in thermostat.  
Check each wire connection to verify they are not shorted  
or touching together. No bare wire should stick out from  
Heat, Cool or Fan  
Runs Constantly  
3. Possible short in heat/cool/fan system. under terminal block. Try resetting the thermostat as  
4. FAN Switch set to Fan ON.  
described above. If the condition persists the manufacturer  
of your system or service person can instruct you on how  
to test the Heat/Cool system for correct operation. If the  
system operates correctly, replace the thermostat.  
Thermostat Setting &  
Thermostat Thermometer  
Disagree  
1. Thermostat thermometer setting  
requires adjustment.  
The thermometer can be adjusted +/- 4 degrees. See  
Temperature Display Adjustment in the Configuration Menu  
section.  
Furnace (Air Conditioner)  
Cycles Too Fast or Too  
Slow (narrow or wide  
temperature swing)  
1. The location of the thermostat and/or  
the size of the Heating System may  
be influencing the cycle rate.  
Digital thermostats provide precise control and cycle faster  
than older mechanical models. The system turns on and off  
more frequently but runs for a shorter time so there is no  
increase in energy use. If you would like an increased cycle  
time, choose SL for slow cycle in the Configuration menu,  
step 6 (heat), 7 (cool) or 8 (heat pump). If an acceptable  
cycle rate is not achieved, contact a local HVAC service  
person for additional suggestions.  
Forgot Keypad Lockout  
Code  
Hold MENU key for 20 seconds and the lockout will reset.  
Thermostat does not have  
Menu Screen Numbers  
1. Earlier version of thermostat.  
Refer to Instruction Sheet 37-7136A.  
9
href="
NOTES  
10  
href="
NOTES  
11  
href="
HOMEOWNER HELP LINE: 1-800-284-2925  
White-Rodgers is a business  
of Emerson Electric Co.  
The Emerson logo is a  
trademark and service mark  
of Emerson Electric Co.