Aube TH132 AFAF Thermostat User Manual

TH1 32 Description

Models Overview

Configure the Switches

Control Module

The TH132 has two switches, located on the upper-left

part on the rear of the control module, which are used to

set the following options:

TH1 32 A/ꢀ/Aꢀ

! DAY/HOUR/MIN—Set the day and clock settings.

TH132-A

PGM—Program the schedule (programs).

Owner!s Guide

This model has been designed to control a room’s ambi-

ent temperature.

The TH132-A has one temperature sensor located in the

control module.

MODE—Select the operating mode.

RETURN—To exit a function.

Thank you for choosing the Aube TH132, a programma-

ble thermostat that provides both energy savings and total

comfort.

Early Start

When the Early Start function is enabled (disabled by

default), the TH132 calculates the optimum system start

time to obtain the desired temperature by the set time. To

enable this function:

$ To configure temperature setpoints:

Comfort, Economy and Vacation.

TH132-AF

This model is designed to use a floor sensor to control the

room temperature.

The TH132-AF has two temperature sensors:

Adjust the floor temperature limit (AF only).

—Increase and decrease temperature.

Position switch #1 down.

Note: When this function is enabled, the

system can be activated before the pro-

gram’s start time.

—Indicates the number of the current

program when Automatic mode is enabled.

•

The first one, installed in the control module, controls

the ambient temperature.

•

The second one, installed in the floor (and connected

to the power base), limits the temperature of the floor

(

Current operating mode (auto

Auto mode, the program’s associated setpoint icon is

also displayed ( ).

manual ). In

Temperature Display

By default, the TH132 displays the temperature in °C. If

you wish to change to °F:

(

the default setting of this limit is 82°F).

TH132-F

)

Indicates the room OR floor temperature.

This model is designed to control floor heating systems.

The TH132-F has one temperature sensor installed in the

floor (sensor is connected to the power base).

Position switch #2 up.

Heating indicators (see “Temperature Control”

below).

Note: When you switch from °C to °F or vice

versa, the

redefined.

and

setpoints must be

WARNING: This control module has 20-second cycles

and must be installed ONLY with a TRIAC relay.

Install the Control Module

ꢀirst Power ON

Adjust the Temperature Setpoints

Select the Operating Mode

Align the bracket tabs on the control module with the

holes located on top of the power base.

This control module must be installed on a PB130-024T

series power base.

On the first installation, the screen displays:

0:00, MO, and temperature (room/floor).

Comfort

and Economy Setpoints

The TH132 offers three operating modes:

These setpoints are associated with the schedule’s pro-

grams (prog. 1 & 3 = Comfort, prog. 2 & 4 = Economy)

and are preprogrammed as follows:

Automatic —Executes the schedule.

For Floor Heating Installations:

One of the two following messages may be dis-

played when a problem occurs:

Press MODE to select

program number is displayed.

. The current

A & AF models— 68°F, 64°F

F model— 82°F, 68°F

To modify a setpoint:

You can temporarily bypass the current

program by setting a specific temperature setpoint

or by selecting one of the pre-defined setpoint

LO: The floor temperature is below 32°F (0°C), or

the temperature sensor is defective, or not

connected.

buttons (

). The new setpoint will be maintained

Set the temperature using and press and hold the

or button until it is displayed on the screen.

The heating indicator

is displayed and

until the beginning of the next program.

the relay is closed (energized).

HI: The floor temperature is above

" Press MODE/RETURN to exit.

Manual —Maintains a constant temperature.

! Press MODE to select

" Set temperature or select one of the pre-

defined setpoint buttons ( ).

40°F (60°C), or the temperature sensor is

Vacation Setpoint

defective.

The vacation setpoint is associated to the Vacation oper-

ating mode and is preprogrammed to 50°F. To modify this

setpoint, repeat above steps.

Set the Time and Day

Vacation —Maintains the Vacation setpoint

during a prolonged absence.

Floor Temperature Setpoint (AF model only)

The floor temperature limit is preprogrammed to 82°F to

avoid damage to your floor.

Set the time (HOUR - MIN).

Set the day (DAY).

Note: Keep the thermostat's air vents clean and free from

Press

obstructions.

To modify, press the adjustment button (below ) using a

Note: The screw cannot be removed completely.

If you remove the module from its base for more than

hours, the time and day will have to be reprogrammed.

pointed object, set the desired temperature using

press MODE/RETURN to exit.

and

00-132-012-A

Note: It is sometimes faster to program the same sched-

ule for the entire week and then to modify the exception

days.

Programming Example

$ Press PGM to select program 2.

Program Your Schedule

Set the time (8:30) using the HOUR and MIN buttons.

% Repeat step 4 for remaining programs:

program 3 (16:00) and program 4 (23:00).

Programs

:00 6:00 6:00 6:00 6:00 6:00 6:00

8:30 8:30 8:30 8:30 8:30 --:-- --:--

The schedule is used with the Automatic mode. The

schedule controls the heating system to automatically

switch between the Comfort and Economy temperature

setpoints at the times you have programmed.

The schedule consists of 4 programs per day defined as

follows:

Press PGM to select the program number (e.g. 1).

Press HOUR and MIN to set the start time.

When all programs are configured, press MODE/

RETURN to exit.

6:00 16:00 16:00 16:00 16:00 --:-- --:--

3:00 23:00 23:00 23:00 23:00 23:00 23:00

% Repeat steps 3 to 4 for remaining programs (e.g. 2, 3

and 4).

To erase programs 2 and 3 for Saturday and

Sunday

Time ⁱ

& Press MODE/RETURN to exit.

Programs

Setpoint

Comfort :

Press PGM.

Note: After 60 seconds of inactivity, the thermostat will

automatically exit programming mode.

• Monday to Friday, between 6:00 and 8:30 and

between 16:00 and 23:00.

• Saturday and Sunday, between 6:00 and 23:00.

Wake-up

" Press PGM to select program 2.

# Press DAY to select SAturday (SA).

$ Press CLEAR to erase the time (--:--).

% Press DAY to select SUnday (SU).

Leave home

Back home

To clear a program time:

Economy :

When you clear a program time entry, the TH132 will

maintain the temperature setpoint of the last executed

program until the beginning of the next program.

• Monday to Friday, between 8:30 and 16:00 and

between 23:00 and 6:00.

Night

Press CLEAR to erase the time (--:--).

•

Saturday and Sunday, between 23:00 and 6:00.

The programs’ start time can be different for each day of the week.

! Repeat steps 1 to 3 above.

Press PGM to select program 3.

Press CLEAR to erase the time entry. The time por-

tion of the LCD indicates --:-- when the program is

inactive.

To program this schedule

( Repeat steps 3 to 6.

) Press MODE/RETURN to exit.

To enter the programs’ start time

To shorten programming, you simply have to enter the

start time for each program.

! Press PGM.

Press and hold DAY for 3 seconds to select all days

of the week.

Press MODE/RETURN to exit.

Press PGM.

Press PGM to select program 1.

Set the time (6:00) using the HOUR and MIN buttons.

Press DAY to select the day (hold for 3 seconds to

select all days of the week).

If you have any questions concerning the programming of

the TH132 programmable thermostat, call our technical

support team at:

Temperature Control

Technical Specifications

Warranty

The TH132 thermostat works differently than conventional

electromechanical thermostats.

It is equipped with a proportional integral adaptive (PIA)

controller which determines heating cycles by analyzing

the temperature behavior history within the room.

The PIA controller reduces temperature swings providing

accurate temperature control while increasing user com-

fort.

The controller determines the amount of power required

by the heating system to maintain the setpoint tempera-

ture.

Model: TH132 A / AF / F

AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY

This product is guaranteed against workmanship defects

for a two-year period following the initial date of purchase.

During this period, AUBE Technologies Inc. will repair or

replace, at our option and without charge, any defective

product which has been used under normal conditions.

Display range: 32°F to 140°F (0°C to 60°C)

Setting range (ambient): 40°F to 86°F (5°C to 30°C)

Setting range (floor): 40°F to 104°F (5°C to 40°C)

Pre-programmed temperature setpoints:

Comfort: A/AF: 68°F (20°C) and F: 82°F (28°C)

Economy: A/AF: 64°F (18°C) and F: 68°F (20°C)

Vacation: A/F/AF: 50°F (10°C)

705 Montrichard

Saint-Jean-sur-Richelieu

Quebec, Canada J2X 5K8

10 rue Ampère

95500 Gonesse

France

The warranty does not cover delivery costs and does not

apply to products poorly installed or randomly damaged

following installation.

Tel.: (450) 358-4600

33 (0) 1 34 07 99 00

Toll Free: 1-800-831-AUBE

Fax: (450) 358-4650

This warranty cancels and replaces any other

manufacturer's express or implied warranty as well as any

other company commitment. AUBE Technologies Inc.

cannot be held liable for related or random damages

following the installation of this product.

33 (0) 1 34 07 99 19

Email: service@aubetech.com advaube@comintes.com

Floor limit: AF: 82°F (28°C)

When the heating system is activated, one of the following

icons is displayed:

Temperature resolution display scale: 0.1°

Storage:-4°F to 120°F (-20°C to 50°C)

Software: Class A

For more information on our products, visit us at:

www.aubetech.com

The defective product as well as the purchase invoice

must be returned to the place of purchase or mailed,

prepaid and insured, to the nearest shipping address.

Controller: Electronic

to 20%

21 to 40% 41 to 60% 61 to 80% 81 to 100%

Temperature control: Proportional integral adaptive,

0-second heating cycles

Programming protection: Protected memory

Clock protection: 2 hours

As an ENERGY STAR partner, Aube Technologies has

determined that this product meets the ENERGY STAR

guidelines for energy efficiency.

Size (H/W/D): 3.3 x 3.1 x 0.5 in (83 x 79 x 13 mm)

0/04/2004 400-132-012-A

PB1 30-024T

Installation Instructions

4 V Low Voltage Power Base

Introduction

The PB130-024T power base is designed to power a TH13X Series

control module. This low voltage power base can be used to drive a

line voltage load using a relay or connect directly to equipment (such

as a hot water system) using a 24 V signal.

Although the PB130-024T is compatible with most relays, it has been

optimized for use with an Aube relay. Aube offers triac relays (SSR)

such as the RT850 and RT850T (with built-in 24 V transformer), and

electromechanical relays such as the RC840 and RC840T (with built-

in 24 V transformer).

Installation Guidelines

Cut power to the heating system at the main power panel to

avoid electrical shock. Installation should be carried out by an

electrician.

For a new installation, choose a location about 5 ft. (1.5 m)

above the floor.

The thermostat should be installed facing the heating system

and on an inside wall.

Avoid locations where there are air drafts (top of staircase, air

outlet), dead air spots (behind a door), direct sunlight or con-

cealed chimneys or stove pipes.

Included Parts

n One (1) PB130-024T low voltage power base

o Two (2) anchors

p Two (2) mounting screws

Installation Steps

n Connect the base. See the typical wiring diagrams.

a) Electric heating (figures 1, 2 and 3)

•

Connect the base to the relay:

•

Use a relay with a built-in 24 V transformer or

Use a relay and an external 24 V transformer.

•

Connect the relay to the load (see relay’s instructions).

b) Hot water heating (figure 4)

•

Connect the base to the 24 V valve of the

water heating system.

o For a floor heating installation, connect the

floor sensor between the S and R terminals.

Technical Specifications

p Push the excess wire into the wall and secure the

Maximum load: 0.5 A / 24 VAC

base using the provided screws and wall anchors.

Operating temperature: 32°F to 122°F (0°C to 50°C)

Storage: -4°F to 122°F (-20°C to 50°C)

Size (H • W • D): 2.94 x 2.94 x 0.53 in. (74.6 x 74.6 x 13.3 mm)

Wire gauge: 14 to 22 AWG

q Before mounting the control module onto the base, select the

heating cycle, set the switches (if necessary) and mount the

control module. Refer to the control module’s user guide for

more information.

r Once the control module is configured (switches) and installed,

If you have any questions concerning the PB130-024T low

voltage power base, call our technical support team at:

return power to the heating system.

05 Montrichard

10 rue Ampère

95500 Gonesse

France

AUBE TECHNOLOGIES INC. TWO (2) YEAR LIMITED WARRANTY

Saint-Jean-sur-Richelieu

Quebec, Canada J2X 5K8

This product is guaranteed against workmanship defects for a two-year period following

the initial date of purchase. During this period, AUBE Technologies Inc. will repair or

replace, at our option and without charge, any defective product which has been used

under normal conditions.

Tel.: (450) 358-4600

Toll Free: 1-800-831-AUBE

Fax: (450) 358-4650

33 (0) 1 34 07 99 00

33 (0) 1 34 07 99 19

The warranty does not cover delivery costs and does not apply to products poorly

installed or randomly damaged following installation. This warranty cancels and replaces

any other manufacturer's express or implied warranty as well as any other company

commitment.

Email: service@aubetech.com advaube@comintes.com

AUBE Technologies Inc. cannot be held liable for related or random damages following

the installation of this product. The defective product as well as the purchase invoice

must be returned to the place of purchase or mailed, prepaid and insured, to the

following address.

For more information on our products, visit us at:

www.aubetech.com

4/11/2003 400-130-002-B