Bryant TSTATBBNAC01 C Thermostat User Manual

Home

Installation, Start-Up

and Operating Instructions

NON-PROGRAMMABLE THERMOSTATS

Cancels: New

II TSTAT-0-34

8-04

NOTE: Read the entire instruction manual before starting the

installation.

This symbol → indicates a change since the last issue.

FAN

SAFETY CONSIDERATIONS

Read and follow manufacturer instructions carefully. Follow all

local electrical codes during installation. All wiring must conform

to local and national electrical codes. Improper wiring or installa-

tion may damage thermostat.

Recognize safety information. This is the safety-alert symbol

When you see this symbol on the equipment and in the instruction

manual, be alert to the potential for personal injury.

TSTATBBNAC01-C

TSTATBBNHP01-C

TSTATBBN2S01-C

Understand the signal words DANGER, WARNING, and CAU-

TION. These words are used with the safety-alert symbol.

DANGER identifies the most serious hazards which will result

in severe personal injury or death. WARNING signifies a hazard

which could result in personal injury or death. CAUTION is used

to identify unsafe practices which would result in minor personal

injury or product and property damage. NOTE is used to highlight

suggestions which may result in enhanced installation, reliability,

or operation.

A04101

DEPTH (IN.)

1-3/8

HEIGHT (IN.)

WIDTH (IN.)

3-1/2

5-3/4

Fig. 1—Bryant Non-Programmable Thermostat

•

Close to or in a frequently used room, preferably on an inside

partitioning wall.

INTRODUCTION

Bryant thermostats are wall-mounted, low-voltage thermostats

which maintain room temperature by controlling the operation of

a heating and air conditioning system. Separate heating and

cooling setpoints, plus auto changeover provide maximum comfort

and flexibility. Batteries are optional; temperature and mode

settings are preserved with the power off.

On a section of wall without pipes or duct work.

Thermostat should NOT be mounted:

•

Close to a window, on an outside wall, or next to a door leading

to the outside.

•

Exposed to direct light and heat from a lamp, sun, fireplace, or

other temperature-radiating object which may cause a false

reading.

INSTALLATION CONSIDERATIONS

POWER

Note that all thermostats are dual powered where batteries can be

installed or in the presence of R and C (24vac) are not required. 2

AA batteries are furnished with the product.

•

Close to or in direct airflow from supply registers and return-air

grilles.

In areas with poor air circulation, such as behind a door or in

an alcove.

MODELS

There are 3 different models. The 9th and 10th letters of the part

number indicate the model. These 2 letters also appear on the

package and on the circuit board. Be sure to have the proper

thermostat for the intended application. Models are:

AC — 1-stage cool, 1-stage heat for AC systems only.

HP — 1-stage cool, 2-stage heat for either HP, or AC with 2-stage

heat.

II. SELECT MODEL

AC Model (1-stage cool, 1-stage heat) is to be used for single-

stage heating and/or cooling applications only. It CANNOT be

used with optional outdoor temperature sensor. (See Table 1.)

HP Model (1-stage cool, 2-stage heat) can be used with a

single-speed heat pump (HP), or an air conditioner (AC) with a

2-stage furnace or fan coil. Software Option 5 selects HP/AC

operation. This thermostat comes configured from the factory as a

heat pump thermostat. Select AC in software Option 5 for AC

operation. When AC operation is selected, the O/W2 terminal is

converted from a reversing valve output (O) to a second-stage heat

output (W2). This output can be used to control 2-stage furnaces or

S — 2-stage cool, 2-stage heat for 2-speed AC systems, or

-stage cool, 3-stage heat for 2-speed HP systems.

USE EACH ONLY FOR ITS INTENDED PURPOSE. SEE

TABLE 1.

INSTALLATION

I. THERMOSTAT LOCATION

Thermostat should be mounted:

-stage electric heat in fan coils. (See Table 1.)

S Model is for 2-speed compressor systems only (HP and AC).

Output Y1 controls compressor low speed and output Y/Y2

controls compressor high speed. (See Table 1.)

•

Approximately 5 ft. (1.5m) from floor.

—

1—

TABLE 1—MODEL SELECTION AND WIRING DIAGRAM CHART

AIR CONDITIONER

Speed

Model AC

HEAT PUMP

OUTDOOR UNIT

-Stage

Furnace

-Stage

2 Speed

Model 2S

See Fig. 8

Model 2S

See Fig. 9

Model 2S

See Fig. 10

1 Speed

Requires

2 Speed

Requires

See Fig. 2

Dual Fuel Thermostat

Requires

Dual Fuel Thermostat

Requires

Model AC

See Fig. 3

Model AC

See Fig. 4

Model HP

See Fig. 5

Model HP

See Fig. 6

Furnace

Dual Fuel Thermostat

Model HP

Dual Fuel Thermostat

Model 2S

Typical Fan Coil

See Fig. 7

See Fig. 11

Variable-Speed

Fan Coil

FK4D, FV4, 40FK)

Model AC

See Fig. 12

Model HP

See Fig. 13

Model 2S

See Fig. 14

Model HP

See Fig. 15

Model 2S

See Fig. 16

(

III. INSTALL THERMOSTAT

10. Snap case back together.

1. Close thermostat assembly making sure pins on back of

circuit board align with sockets in connector.

WARNING: ELECTRICAL SHOCK HAZARD

Failure to follow this warning could result in personal

injury or death.

Before installing thermostat, turn off all power to unit.

There may be more than 1 power disconnect.

2. Turn ON power to unit.

NOTE: If a common wire has not been connected, two AA

batteries must be used to power the thermostat.

On power up, LCD readout will display AC, HP, A2, or H2

depending on the thermostat model status. See "Power On Check"

under "Operational Information" on page 11 for explanation.

. Turn OFF all power to unit.

IV. SET THERMOSTAT CONFIGURATION

. If an existing thermostat is being replaced:

a. Remove existing thermostat from wall.

Configuration options are intended to be selected at installation

and are normally not modified by the home owner. These options

are not discussed in the Homeowner’s Guide and therefore must be

made as part of the installation. A special procedure allows entry

into the configuration mode. The thermostat will automatically exit

this mode if no button is pressed for 3 minutes. While in the

configuration mode, up to 14 option choices can be made:

b. Disconnect wires from existing thermostat, 1 at a time.

Be careful not to allow wires to fall back into the wall.

c. As each wire is disconnected, record wire color and

terminal marking.

d. Discard or recycle old thermostat.

Option 01: Anticipator setting

Option 02: Clean filter setting

NOTE: Mercury is a hazardous waste and MUST be disposed of

properly.

Option 03: Fahrenheit or Celsius selection

Option 04: Enable fan (G) on with W/W1 output

Option 05: HP / AC

Option 06: Cooling Lockout (available only if an outdoor air

temperature sensor is present)

. Open thermostat (mounting base) to expose mounting

holes. The base can be removed to simplify mounting. Snap

apart carefully to separate mounting base from remainder of

thermostat.

NOTE: If thermostat will not separate, insert a small screwdriver

into top slots for ease of opening.

Option 07: Enable zoning

Option 08: Auxiliary heat lockout temperature adjustment (avail-

able only on heat pump systems and if an outdoor air temperature

sensor is present)

Option 10: O (reversing valve) ON with Heat or Cool (present on

Heat Pump models only)

. Route thermostat wires through large hole in mounting

base. Level mounting base against wall (for aesthetic value

only—thermostat need not be leveled for proper operation)

and mark wall through 2 mounting holes.

. Drill two 3/16-in. mounting holes in wall where marked.

Option 13: Room temperature offset adjustment

Option 15: Enable AUTO mode

Option 18: Backlight configuration

Option 19: Equipment Present

. Secure mounting base to wall with 2 anchors and screws

provided, (additional anchoring holes available for more

secure mounting if needed) making sure all wires extend

through hole in mounting base.

Option 21: Keypad Lockout

An explanation for each of these and how to enter the configura-

tion mode follows.

. Adjust length and routing of each wire to reach proper

terminal and connector block on mounting base with 1/4 in.

extra wire. Strip only 1/4 in. insulation from each wire to

prevent adjacent wires from shorting together when con-

nected.

TO ENTER THE CONFIGURATION MODE:

To enter Configuration Mode, hold the FAN button down for

approximately 15 seconds. After the 15 second period, Option

″01″ will appear in the display and the SERVICE icon will be

turned on.

. Match and connect equipment wires to proper terminals of

the connector blocks. (See Table 1.)

NOTE: If the FAN button is pressed again or if no button is

pressed for 3 min, the thermostat will exit the configuration mode

and return to normal operation. To reenter the configuration mode,

the FAN button must be pressed and held for 15 seconds again.

CAUTION: ELECTRICAL OPERATION HAZARD

Failure to follow this caution may result in equipment

damage or improper operation.

Improper wiring or installation may damage the thermo-

stat. Check to make sure wiring is correct before proceed-

ing with installation or turning on unit.

WHILE IN CONFIGURATION MODE:

The display is used to show both the option number and the

selection choice within that option.

A. Option 01—Anticipator Adjustment

. Push any excess wire into wall and against mounting base.

Seal hole in wall to prevent air leaks. Leaks can affect

operation.

This adjustment controls the sensitivity and cycle rate of the

thermostat. Higher numbers decrease the sensitivity and slow the

cycle rate. Lower numbers increase sensitivity and increase cycle

—

2—

rate. However, a limiting feature will not allow more than 6

equipment cycles per hour, regardless of setting. Values can range

from 1 to 9. Factory default setting is 3. This default selection will

provide optimum performance in nearly all installations. Try it

first. Do not change setting unless there is evidence of need to do

so.

D. Option 04—G (Fan) On With W/W1 Output

This selection determines whether the G (fan) output is to be ON

or OFF when any W (furnace or strip heat) output is ON. Most

furnaces and fan coils manage their own blowers and do not

require a separate G signal. For these applications, select OFF.

Some auxiliary heaters require a separate G signal to turn on the

blower. In this case, select On. Factory default is OF (off).

Unlike conventional anticipators, this setting is not to be deter-

mined by current draw. There is no need to measure, know, or

compensate for current. There is also no droop with this thermo-

stat, regardless of anticipator setting. This adjustment controls only

sensitivity and cycle rate up to the maximum of 6 cycles per hr.

TO SELECT:

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 04. The SET

icon should be off.

TO ADJUST:

. Press MODE button once. The SET icon will come on. The

display now shows Option 04 setting.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 01. The SET

icon should be off.

. Use up and down buttons to move between available Option

4 choices of ON or OF. Factory default is OF.

. Press MODE button once. The SET icon will come on. The

display now shows Option 01 setting.

5. Press MODE button again to return to Option 04. The SET

icon will now be off.

. Use up and down buttons to move between the available

Option 01 values of 1 to 9. Factory default is 3.

6. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

E. Option 05 — HP and 2S / AC Configuration

. Press MODE button again to return to Option 01. The SET

icon will now be off.

This configuration is available on HP and 2S models only.

Selecting AC allows the installer to use an HP or 2S thermostat in

an AC application.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

TO SELECT:

B. Option 02—Clean Filter Timer

. Enter configuration mode (if not already there).

This option selects the number of hours of blower operation

heating, cooling, or fan) before SERVICE FILTER icon is

. Use up and down buttons to display Option 05. The SET

icon should be off.

(

displayed. With OF selected, the icon will never come on,

disabling this feature. Time selection can be from 400 to 3600

hours by selecting numbers 1 through 9. (Time is 400 X number

selected.) Factory default is 2 (800 hours). Recommended selec-

tions are: disposable filter 800 hr, media filter 1200 to 1600 hr, or

electronic air cleaner 1600 to 2400 hr of blower operation.

. Press MODE button once. The SET icon will come on. The

display now shows Option 05 setting.

. Use up and down buttons to move between available Option

5 choices of AC or HP. Factory default is HP.

5. Press MODE button again to return to Option 05. The SET

icon will now be off.

TO ADJUST:

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 02. The SET

icon should be off.

F. Option 06—Cooling Lockout

An outdoor air sensor is required for this function. In OF mode,

cooling is available regardless of outdoor temperature. In ON

mode, cooling will not be initiated if the outdoor air temperature is

below 55° F. If the compressor is already operating and the

outdoor air temperature drops below 55° F, the compressor will

continue to operate until the cooling cycle has completed. If the

mode has been set to ON and the outdoor air sensor fails, an E3

error will be displayed.

. Press MODE button once. The SET icon will come on. The

display now shows Option 02 setting.

. Use up and down buttons to move between the available

Option 02 values of OF and 1 through 9. Factory default is

. Press MODE button again to return to Option 02. The SET

icon will now be off.

TO SELECT:

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 06. The SET

icon should be off.

C. Option 03—Fahrenheit/Celsius Selection

This option selects Fahrenheit or Celsius operation.

TO SELECT:

. Press MODE button once. The SET icon will come on. The

display now shows Option 06 setting.

. Use up and down buttons to move between available Option

. Enter configuration mode (if not already there).

6 choices of OF or ON. Factory default is OF.

. Use up and down buttons to display Option 03. The SET

icon should be off.

. Press MODE button again to return to Option 06. The SET

icon will now be off.

. Press MODE button once. The SET icon will come on. The

display now shows Option 03 setting.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Use up and down buttons to move between the available

Option 03 choices of F (Fahrenheit) or C (Celsius). Factory

default is F.

G. Option 07—Zoning On/Off Configuration

This selection enables or defeats the cycle timer, the staging timer,

and the compressor timeguard. (See "Operational Information" on

page 11 for details.) These timers MUST be enabled (zoning OFF)

for normal operation and disabled (zoning ON) for zoning appli-

cations. In zoning applications, the zone control center performs

these timing functions. Factory default is OF.

. Press MODE button again to return to Option 03. The SET

icon will now be off.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

—

3—

TO SELECT:

default is 0. This adjusted value will be used as actual temperature

for both display and control action. For example, if 2 is selected,

. Enter configuration mode (if not already there).

2°F actual will read 74°F. If setpoint is 72, the room will control

. Use up and down buttons to display Option 07. The SET

icon should be off.

to an actual value of 70 which will be displayed and acted upon as

if it were 72. The effect is that a positive number selection will

make the room temperature lower and vice versa. This thermostat

is factory calibrated within an accuracy of plus or minus 1°F, so

this adjustment will provide the best accuracy when set to 0.

. Press MODE button once. The SET icon will come on. The

display now shows Option 07 setting.

. Use up and down buttons to move between available Option

TO SELECT:

7 choices of ON or OF. Factory default is OF.

. Enter configuration mode (if not already there).

. Press MODE button again to return to Option 07. The SET

icon will now be off.

2. Use up and down buttons to display Option 13. The SET

icon should be off.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

3. Press MODE button once. The SET icon will come on. The

display now shows Option 13 setting.

H. Option 08—High Ambient Auxiliary Heat Lockout

. Use up and down buttons to move between available Option

Present in HP and 2S models only when configured as a heat

pump. Outdoor temperature sensor must be attached. This selec-

tion allows lockout of any electric heat (W output) when outdoor

temperature is above a selected temperature. Temperatures of 5° to

3 choices of -5 through +5 in 1° steps. Factory default is

5. Press MODE button again to return to Option 13. The SET

icon will now be off.

5°F (or equivalent values in C) can be selected. Feature can be

disabled by selecting OFF. Emergency heat (EHEAT mode)

always overrides this feature.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

TO SELECT or ADJUST:

K. Option 15—Auto Mode On/Off Selection

. Enter configuration mode (if not already there).

This options allows the installer to enable or disable AUTO mode

(automatic changeover between heat and cool). When disabled,

AUTO icon does not appear when successive presses of MODE

button are used to move between OFF, HEAT, and EHEAT (in

heat pump systems). Factory default is ON (AUTO mode enabled).

. Use up and down buttons to display Option 08. The SET

icon should be off.

. Press MODE button once. The SET icon will come on. The

display now shows Option 08 setting.

TO SELECT:

. Use up and down buttons to move between available Option

8 choices of OF, or 5 through 55 in 5° steps. Factory

1. Enter configuration mode (if not already there).

default is OF.

. Use up and down buttons to display Option 15. The SET

icon should be off.

. Press MODE button again to return to Option 08. The SET

icon will now be off.

. Press MODE button once. The SET icon will come on. The

display now shows Option 15 setting.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Use up and down buttons to move between available Option

15 choices of ON or OF. Factory default is ON.

I. Option 10 — O (reversing valve) On with Heat or Cool

Selection

. Press MODE button again to return to Option 15. The SET

icon will now be off.

This selection is only available on HP and 2S model thermostats

when HP is selected via Option 05. This selection determines

whether the reversing valve is energized in the heating or cooling

mode. Factory default is C, energized in cooling. Use up and down

buttons to change between H and C.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

L. Option 18 — Backlight Configuration

TO SELECT:

This function is only available when the thermostat is operating

from full power via R and C. It is not available when the

thermostat operates from batteries. In OF (off) mode, this function

is disabled. The thermostat backlight will normally be off. It turns

on with any button press and stays on for 10 seconds in between

button presses. In ON mode, this function is enabled. The

thermostat backlight will normally be on and dim in appearance.

The backlight becomes brighter with any button press and remains

bright for 10 seconds. Factory default is OF.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 10.

. Press MODE button once. The SET icon will come on. The

display now shows Option 10 setting.

. Use up and down buttons to move between available Option

0 choices of H (heat) or C (cool). Factory default is C.

. Press MODE button again to return to Option 10. The SET

icon will now be off.

TO SELECT:

. Enter configuration mode (if not already there).

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Use up and down buttons to display Option 18. The SET

icon should be off.

J. Option 13—Room Temperature Offset

. Press MODE button once. The SET icon will come on. The

display now shows Option 18 setting.

This option allows calibration (or deliberate miscalibration) of

room temperature sensor. There are various reasons why the home

owner may want to have displayed temperature adjusted to a

higher or lower value. The selected number is the number of

degrees, plus or minus, which will be added to the actual

temperature. The number can range between -5 and +5. Factory

. Use up and down buttons to move between available Option

8 choices of ON or OF. Factory default is OF.

5. Press MODE button again to return to Option 18. The SET

icon will now be off.

—

4—

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

In installer test mode, pressing the MODE button will change the

system operating mode. Note that AUTO mode is not available in

installer test. Heating and cooling modes must be tested indepen-

dently.

M. Option 19 — Equipment Present

This selection informs the thermostat of the heat, cool, and fan

capabilities of the installed equipment. Select number 2, 3, or 4.

Default is 4.

For equipment with both heat and cool capability and fan selection,

choose 4.

For equipment with only heat or cool, but with fan selection,

choose 3.

For equipment with only heat or cool and no fan selection, choose

a. If the mode is set to HEAT, the first stage of heating will

be energized for three minutes (180 seconds), and then

the first and second stages (if a second stage exists) will

turn on for an additional three minutes. Installer test will

always attempt to run a second stage output whether it is

attached or not, providing a minimum of 6 minutes of

first stage operation. At the end of the 6 minute period,

the MODE will return to OFF.

TO SELECT:

b. Pressing the FAN button while the heating or cooling

equipment is not running will turn on the FAN relay and

display the FAN icon.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 19. The SET

icon should be off.

c. If the mode is set to COOL, the first stage of cooling

turns on for three minutes, then first and second stages (if

a second stage exists) will turn on for three minutes.

. Press MODE button once. The SET icon will come on. The

display now shows Option 19 setting.

. Use up and down buttons to move between available Option

d. If the mode is set to EHEAT, auxiliary heat turns on for

three minutes, then the mode returns to OFF.

9 choices of 2 through 4. Factory default is 4.

. Press MODE button again to return to Option 19. The SET

icon will now be off.

Terminating Installer Test

After 15 minutes of inactivity (no button presses by the installer),

thermostat will automatically revert to normal operation. Pressing

RESET FILTER any time during installer test will terminate

installer test and return the thermostat to normal operation.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

N. Option 21 — Keypad Lockout

In OF (off) mode, the keypad is not locked out and has full

functionality. In ON mode, the keypad is locked out and the lock

icon on the display is illuminated. To unlock the keypad, the user

must press and hold the up and down buttons simultaneously for

approximately 5 seconds. The lock icon is turned off and the

keypad will remain unlocked as long as the user presses a button

at least every 30 seconds or for the entire duration of the installer

test mode. If keypad remains idle for 30 seconds and the installer

test mode is not in operation, the keypad will return to the locked

state and the lock icon will illuminate on the screen.

V. CHECK THERMOSTAT OPERATION

A. Fan Operation

. Press FAN button, starting continuous fan operation. FAN

icon turns on.

. Press FAN button again, stopping fan operation. FAN icon

turns off. (Some fan coils have 90 sec fan off delay, so fan

may not stop immediately.)

B. Outdoor Temperature Sensor

TO SELECT:

If system is equipped with an outdoor temperature sensor, check its

operation by pressing both, the temperature UP and DOWN

buttons simultaneously. Outdoor temperature will be displayed for

about 5 sec. If ″--″ is displayed, the outdoor temperature sensor is

absent or not properly connected.

. Enter configuration mode (if not already there).

. Use up and down buttons to display Option 21. The SET

icon should be off.

. Press MODE button once. The SET icon will come on. The

display now shows Option 21 setting.

C. Checklist

. Use up and down buttons to move between available Option

. Run equipment through several heating and cooling cycles

to ensure proper operation.

1 choices of ON or OF. Factory default is OF.

. Press MODE button again to return to Option 21. The SET

icon will now be off.

2. If equipment is to be left in operation, set point and

operating mode must be properly selected.

. Use up and down buttons to select another Option, or press

FAN button to exit configuration mode.

. Put away tools and instruments, and clean up debris.

. Review Homeowner’s Guide with owner.

O. Installer Test Mode

Installer test will be initiated by pressing the fan button for 20

seconds (15 seconds will enter installer setup. InS will appear on

the screen and the SERVICE icon will be illuminated.

5. Leave literature packet with owner.

—

5—

TABLE 2—NON-PROGRAMMABLE -C THERMOSTAT QUICK REFERENCE

THERMOSTAT OUTPUT

Hot

Heat

Cool

TSTAT Model Outdoor Unit Option 5

Common Fan

Reversing Valve

Stage 1 Stage 2 Stage 3 Stage 1 Stage 2

AC01-C

HP01-C

N/A

OFF

W/W1

Y/Y2

W/W1

N/A

Y/Y2

N/A

O/W2/B

N/A

W/W1

O/W2/B

Y/Y2

N/A

2S01-C

S01-C

2-Speed AC

2-Speed HP

N/A

Y/Y2

N/A

OFF

W/W1

O/W2/B

Model Numbers: TSTATBBNAC01-C, TSTATBBNHP01-C, TSTATBBN2S01-C

Note: AC = Air Conditioner, HP = Heat Pump, 2S = 2-Speed, N/A = Not Applicable

MODEL AC 01-C

THERMOSTAT

SINGLE-STAGE

FURNACE

SINGLE-SPEED

TWO-STAGE OR

VARIABLE-SPEED

FURNACE

AIR CONDITIONER

MODEL AC 01-C

THERMOSTAT

SINGLE-SPEED

AIR CONDITIONER

4 VAC HOT

24 VAC COMM

HEAT STAGE 1 W/W1

COOL STAGE 1 Y/Y2

HEAT STAGE 1 W/W1

COOL STAGE 1 Y/Y2

W/W1

Y/Y2

FAN

HUM

See note 11

A04006

See note 1 and 11

A04007

Fig. 2—Single-Speed Air Conditioner

with Single-Stage Furnace

HUM

Fig. 3—Single-Speed Air Conditioner

with 2-Stage or Variable-Speed Furnace

TWO-STAGE OR

MODEL HP 01-C

THERMOSTAT

VARIABLE-SPEED

FURNACE

SINGLE-SPEED

AIR CONDITIONER

4 VAC HOT

4 VAC COMM

HEAT STAGE 1 W/W1

COOL STAGE 1 Y/Y2

W/W1

Y/Y2

FAN

MODEL AC 01-C

THERMOSTAT

TYPICAL

FAN COIL

SINGLE-SPEED

AIR CONDITIONER

4 VAC HOT

HUM

24 VAC COMM

HEAT STAGE 2 O/W2/B

FAN

N/A

COOL STAGE 1 Y/Y2

HEAT STAGE 1 W/W1

OUTDOOR

SENSOR

See notes 2, 3, 4 and 11

CONNECTION

See notes 6, 10 and 11

A98453

A04008

Fig 4—Single-Speed Air Conditioner

with Typical Fan Coil

Fig. 5—Single-Speed Air Conditioner

with 2-Stage or Variable-Speed Furnace

—

6—

MODEL HP 01-C

THERMOSTAT

TYPICAL

FAN COIL

SINGLE-SPEED

MODEL HP 01-C

THERMOSTAT

TYPICAL

SINGLE-SPEED

HEAT PUMP

AIR CONDITIONER

FAN COIL

4 VAC HOT

24 VAC COMM

HEAT STAGE 1 W/W1

COOL STAGE 1 Y/Y2

FAN

COOL/ HEAT

STAGE 1

Y/Y2

FAN

HEAT STAGE 2 W/W1

RVS COOLING O/W2/B

HEAT STAGE 2 O/W2/B

N/A

OUTDOOR

SENSOR

OUTDOOR

SENSOR

See notes 6, 7, 10 and 11

See notes 2, 4, 6, 10 and 11

A98455

CONNECTION

A98456

Fig. 7—Single-Speed Heat Pump

with Typical Fan Coil

Fig. 6—Single-Speed Air Conditioner

with Typical Fan Coil

TWO-STAGE OR

MODEL 2S 01-C

SINGLE-STAGE

FURNACE

TWO-SPEED

MODEL 2S 01-B

TWO-SPEED

VARIABLE-SPEED

FURNACE

THERMOSTAT

4 VAC HOT

AIR CONDITIONER

THERMOSTAT

AIR CONDITIONER

24 VAC HOT

4 VAC COMM

24 VAC COMM

HEAT STAGE 1 W/W1

COOL STAGE 2 Y/Y2

HEAT STAGE 1 W/W1

W/W1

COOL STAGE 2

FAN

Y/Y2

FAN

HUM

ACRDJ

N/A

HEAT STAGE 2

COOL STAGE 1

N/A

O/W2/B

COOL STAGE 1 Y1

HUM

N/A

OUTDOOR

SENSOR

OUTDOOR

SENSOR

See notes 2, 5, 8, and 11

See notes 2, 3, 4, 8, 9, and 11

A04010

CONNECTION

A04009

Fig. 8—Two-Speed Air Conditioner

with Single-Stage Furnace

Fig. 9—Two-Speed Air Conditioner

with 2-Stage or Variable-Speed Furnace

—

7—

MODEL 2S 01-c

THERMOSTAT

TYPICAL

TWO-SPEED

MODEL 2S 01-C

THERMOSTAT

TYPICAL

FAN COIL

TWO-SPEED

HEAT PUMP

FAN COIL

AIR CONDITIONER

4 VAC HOT

24 VAC HOT

24 VAC COMM

FAN

24 VAC COMM

HEAT STAGE 1 W/W1

COOL STAGE 2 Y/Y2

COOL/HEAT

STAGE 2

Y/Y2

W/W1

FAN

HEAT STAGE 3

HEAT STAGE 2 O/W2/B

COOL STAGE 1 Y1

RVS COOLING O/B/W2

COOL/HEAT

STAGE 1

N/A

OUTDOOR

SENSOR

OUTDOOR

SENSOR

CONNECTION

See notes 2, 4, 5, 6, 8, 10 and 11

See notes 5, 6, 7, 8, 10, and 11

A04011

Fig. 11—Two-Speed Heat Pump

with Typical Fan Coil

Fig. 10—Two-Speed Air Conditioner^A⁹⁸⁴⁵⁹

with Typical Fan Coil

MODEL HP 01-C

THERMOSTAT

EASY SELECT

TERMINAL BOARD

SINGLE-SPEED

AIR CONDITIONER

J1 JUMPER

4 VAC HOT

MODEL AC 01-C

THERMOSTAT

EASY SELECT

TERMINAL BOARD

SINGLE-SPEED

AIR CONDITIONER

HEAT STAGE 1 W/W1

24 VAC COMM

J1 JUMPER

Y/Y2

4 VAC HOT

COOL STAGE 1

FAN

Y/Y2

HEAT STAGE 1

W/W1

J2 JUMPER

Y/Y2

REMOVE

J2 JUMPER

FOR HEAT

STAGING

COOL STAGE 1 Y/Y2

HEAT STAGE 2 O/W2/B

FAN

N/A

4 VAC COMM

See notes 2, 4, 10 and 11

OUTDOOR

SENSOR

See note 10 and 11

A98463

CONNECTION

A98464

Fig. 12—Single-Speed Air Conditioner

Fig. 13—Single-Speed Air Conditioner

with Variable Speed (FK4D, FV, 40FK) Fan Coil

with Variable-Speed (FK4D, FV, 40FK) Fan Coil

—

8—

MODEL 2S

THERMOSTAT

EASY SELECT

TWO-SPEED

MODEL HP

THERMOSTAT

EASY SELECT

SINGLE-SPEED

HEAT PUMP

TERMINAL BOARD

AIR CONDITIONER

TERMINAL BOARD

J1 JUMPER

4 VOLT HOT

4 VAC HOT

4 VOLT COMM

24 VAC COMM

FAN

COOL STAGE 2 Y/Y2

HEAT STAGE 1 W/W1

Y/Y2

COOL/HEAT

STAGE 1

Y/Y2

HEAT STAGE 2 W/W1

REMOVE

J2 JUMPER

FOR HEAT

STAGING

J2 JUMPER

HEAT STAGE 2 O/B/W2

N/A

COOL STAGE 1

N/A

RVS COOLING O/W2

N/A

OUTDOOR

SENSOR

See notes 7, 8, and 11

OUTDOOR

SENSOR

CONNECTION

See notes 2, 4, 8, 10, and 11

CONNECTION

Fig. 15—Single-Speed Heat Pump with Variable-Speed

FK4D, FV4, 40FK) Fan Coil

Fig. 14—Two-Speed Air Conditioner with Variable-Speed

FK4D, FV4, 40FK) Fan Coil

(

A98466

A04012

MODEL 2S

THERMOSTAT

EASY SELECT

TWO-SPEED

HEAT PUMP

TERMINAL BOARD

J1 JUMPER

4 VAC HOT

4 VAC COMM

FAN

COOL/HEAT

STAGE 2

Y/Y2

HEAT STAGE 3 W/W1

J2 JUMPER

RVS COOLING O/B/W2

COOL/HEAT

STAGE 1

N/A

OUTDOOR

SENSOR

See notes 7, 10 and 11

CONNECTION

Fig. 16 — Two-Speed Heat Pump with Variable-Speed

FK4D, FV4) Fan Coil

(

A04013

—

9—

WIRING DIAGRAM NOTES:

. Furnace must control its own second-stage heat operation via furnace control algorithm. Refer to indoor equipment Installation Instructions

for proper setup.

. See Option 5 information to convert HP and 2S thermostats to AC thermostat operation.

. As an option, lock the furnace into low-heat operation and let O/W2/B control high-heat operation. Refer to indoor equipment Installation

Instructions for proper setup.

. O/W2/B can control second-stage heat. Refer to indoor equipment Installation Instructions for proper setup.

. Refer to outdoor equipment Installation Instructions for latent kit requirements (if any).

. Terminals marked with * may not be present on equipment.

. O/W2/B energizes reversing valve in cooling or heating. See Option 10.

. Refer to outdoor equipment Installation Instructions for proper setup.

. If system is wired per diagram, the ACRDJ (jumper) on furnace control board should be removed to allow thermostat to control outdoor

unit staging.

0. Refer to fan coil Installation Instructions for proper wiring.

1. If batteries are installed, C (common wire) is not required between indoor unit and thermostat.

—

10—

OPERATIONAL INFORMATION

FIVE-MINUTE COMPRESSOR TIMEGUARD

This timer prevents the compressor from starting unless it has been off for at least 5 minutes. It can be defeated for 1 cycle by simultaneously

pressing the FAN mode button and the INCREASE TEMPERATURE button.

FIFTEEN-MINUTE CYCLE TIMER

This timer prevents the start of a heating or cooling cycle until at least 15 minutes after the last start of the same cycle. Its function is to assure

that equipment is not cycled more than 4 times per hr. This timer is defeated for 1 cycle when the desired temperature is manually changed. It

can also be defeated for 1 cycle by simultaneously pressing the FAN mode button and the INCREASE TEMPERATURE button.

FIFTEEN-MINUTE STAGING TIMER

In multistage heating or cooling, this timer prevents any higher stage from turning on until the preceding stage has been on for 15 minutes. This

timer is defeated if the temperature error is greater than 5°F (usually due to a large change in desired temperature).

THREE-MINUTE MINIMUM ON TIME

In normal operation, when a stage turns on, it will not turn off for a minimum of 3 minutes.

HEAT/COOL SET POINTS (DESIRED TEMPERATURES)

A minimum difference of 2°F is enforced between heating and cooling set points. This is done by allowing one setting to "push" the other, to

maintain this difference.

AUTO CHANGEOVER

When the auto changeover mode is selected, a change from heat to cool (or vice versa) will not occur until an opposite mode demand has existed

for 20 minutes. If the set point is changed, the 20 minute requirement is deleted. Auto mode may be disabled.

EMERGENCY HEAT MODE

When thermostat is configured as a heat pump and emergency heat mode is selected, all Y signals are locked out and W becomes energized upon

a call for heat.

HEAT ON AND COOL ON ICONS

When a heating or cooling demand exists, the HEAT ON or COOL ON icon will either remain on or flash. If flashing, the equipment is temporarily

prevented from turning on by one of the timers (see above). While the icon remains on without flashing, the equipment is on.

POWER ON CHECK

When AC power is first applied, all segments of the display are turned on for a few sec. Following this, the temperature display indicates the

model/configuration via the following 2 digit code:

AC—1-speed air conditioner, HP—1-speed heat pump, A2—2-speed air conditioner, H2—2-speed heat pump.

ERROR CODES

-- — If the thermostat cannot properly read room temperature, the display will indicate -- (2 dashes) and all outputs (except the fan if on) will

turn off. This is to prevent operation of the equipment if the thermostat has failed.

E2 — If the AC line voltage drops below a minimum (brownout) level, all outputs are turned off and the display indicates E2. This condition will

remain for 15 sec after proper line voltage is restored. If the AC line voltage disappears completely, the display will immediately go blank.

E3 — If the thermostat cannot properly read outdoor temperature, and it is needed for proper operation (Heat pump system and Option 8 is not

set to OF), E3 will flash alternately with room temperature.

THERMOSTAT TROUBLESHOOTING

SYMPTOM

Blank LCD

WHAT TO CHECK

Check for 24vac between R and C at terminal connections or battery.

Temperature sensor reading out of range. Check sensor for damage. If recycling power

does not clear display, thermostat should be replaced.

"--" (2 dashes) on temperature display

Brownout condition or too low of voltage to thermostat. Double check wiring and check for

E2" on temperature display

E3" on temperature display

24vac between R and C. E2 will clear 15 sec after proper voltage is restored.

The outdoor temperature sensor is open, not connected, or shorted.

After the selected number of hour of blower operation "FILTER" will display on LCD. This

is to remind the home owner to "check" the filter. Press RESET FILTER button to clear

display and reset timer to 0.

"SERVICE FILTER" on temperature display

Select COOL mode. Set desired temperature to 10°F below room temperature. Simulta-

neously press FAN and INCREASE TEMPERATURE buttons to defeat timers. Check for

COOL ON icon and 24vac at Y (first-stage) terminal. If present, thermostat is OK and

problem is with equipment or wiring. If not present, replace thermostat.

Cooling will not come on

Select HEAT mode. Set desired temperature to 10°F above room temperature. Simulta-

neously press FAN and INCREASE TEMPERATURE buttons to defeat timers. Check for

HEAT ON and 24vac at Y (first-stage) terminal (with heat pump) or W/W1 (with air condi-

tioner) terminal. If present, thermostat is OK and problem is with equipment or wiring. If

not present, replace thermostat.

Heating will not come on

—

11—

NON-PROGRAMMABLE THERMOSTAT CONFIGURATION RECORD

Date

Owner/Operator

Thermostat Model No.

A) Hardware Configuration

Seal hole in wall.

B) Mode Settings

Mode (Off, Heat, Cool, Auto, Eheat)

Heating Set Point Value

Cooling Set Point Value

Fan (Auto or On)

C) Configuration Options

Anticipator (1-9: factory default = 3)

Clean Filter Timer (Off or 1-9: factory default = 2)

Fahrenheit or Celsius (F or C: factory default = F)

Fan On with W/W1 output (Off or On: factory default = Off)

HP (2-speed) / AC Configuration

Cooling Lockout (Off or On: factory default = Off)

Zoning Selection (Off or On: factory default = Off)

Auxiliary Heat Lockout (Off or 5-55°F: factory default = Off)

N/A

O(Reversing Valve) ON with Heat or Cool (present on Heat Pump models only.

N/A

Room Temperature Offset (-5 to +5: factory default = 0)

N/A

Enable Auto Mode (Off or On: factory default = On)

N/A

Backlight Configuration: (On = Continuous; Off = Backlight with Keypress; Default = Off)

Equipment Present (2, 3, 4); Default = 4

N/A

1-12

6-17

A04105

Keypad lockout (Off or On: Default = Off)

2004 Bryant Heating & Cooling Systems 7310 W. Morris St. Indianapolis, IN 46231

Printed in U.S.A.

iitstat-0-34

Catalog No. 13TS-TA65

—

12—

White Rodgers 1F80 41 Thermostat User Manual

Lux Products T20 1141 Thermostat User Manual

Carrier 4850HJ004 024 Thermostat User Manual

Honeywell CM907 Thermostat User Manual

Honeywell T874A Thermostat User Manual

Lennox 43558 Thermostat User Manual

Honeywell 8000 Thermostat User Manual

Honeywell T874D Thermostat User Manual

Honeywell WEB 201 Thermostat User Manual

Honeywell T8011 Thermostat User Manual