Honeywell CT33 Thermostat User Manual

Home

href="
Owner’s  
Manual  
CT30/CT33  
Low-voltage Thermostat  
Getting started  
Check to make sure your package includes the following items:  
Wire labels  
Caution card  
Wall anchors and  
mounting screws  
2 each)  
(
CT30/CT33 thermostat  
Cover plate  
Before you begin, make sure you have:  
Screwdriver  
Hammer  
Level (optional)  
Pencil  
Drill bit (3/16”for drywall, 7/32”for plaster)  
®
U.S. Registered Trademark. Patents pending.  
Copyright © 2005 Honeywell International Inc.  
All rights reserved.  
href="
Owner’s Manual  
Remove your old thermostat  
1
2
Turn off power at heating/cooling system (or fuse/circuit-breaker panel).  
Remove cover and thermostat, but leave wallplate with wires attached.  
Leave wallplate in place  
Is there a sealed tube containing mercury?  
If so, see mercury notice below.  
Old thermostat  
Cover  
MERCURY NOTICE: Do not place your old thermostat in the trash if it contains  
mercury in a sealed tube. Contact your local waste management authority for  
instructions regarding recycling and proper disposal.  
Did you purchase right thermostat? Count wires to check.  
Count the number of wires coming out of the wall and attached to terminals in  
your old thermostat. If any of them are attached to a terminal marked“C”or“C1”  
do not count that wire in your total.  
If the total (not counting C or C1) is 2 wires, proceed to the next page. If you have  
3
or more wires, your new thermostat may not be compatible with your system.  
Stop installation and call 1-800-468-1502 for advice.  
Do you have 3 or more wires? If so, stop now.  
You may have purchased the wrong replace-  
ment thermostat.  
2
href="
CT30/CT33 Low-voltage Thermostat  
Label wires and remove old wallplate  
Use a screwdriver to disconnect wires one by one.As you disconnect each wire,  
wrap it with the label matching the letter on your old thermostat. (Adhesive labels  
are supplied in your thermostat package.)  
Remove the old wallplate only after all wires are labeled. Be careful not to let  
loose wires fall into the wall opening.  
Wrap supplied labels securely around each wire  
Do not let wires fall into wall opening!  
IGNORE WIRE COLORS: Use only letter designations  
to identify wire types.  
Mark mounting position  
1
Level base or cover plate  
if desired.  
2
Mark positions of  
both screw holes.  
3
href="
Owner’s Manual  
Mount thermostat base  
1
Drill holes at pencil-marked locations (3/16” holes for drywall, 7/32” holes for plaster).  
2
Use hammer to  
tap anchors into  
holes until flush  
with wall.  
3
4
[Optional] Pull  
wires through  
cover plate (if  
needed to cover  
marks left by your  
old thermostat).  
Connect wires first  
(see below), then  
insert screws.  
Check level if  
desired, then  
tighten screws.  
Optional cover plate  
Thermostat base  
Wire connections  
1
Match each labeled wire  
with same letter on terminal.  
2
Use a screwdriver to loosen  
screw terminals, wrap bare  
wire securely around termi-  
nals, then tighten screws.  
3
Push any excess wire back  
into the wall opening.  
Labels don’t match?  
If labels do not match letters on  
thermostat, see table below.  
Existing wires  
R  RH  4  V  
W  W1  H  
Y Y1 M  
G F  
Connect to:  
Terminal “R”  
Terminal “W”  
Back of thermostat base  
Stop! See note  
Stop! See note  
Stop! See note  
If any of these wires are present, you  
cannot use this thermostat with your  
system. See page 2.  
Rc  
4
href="
CT30/CT33 Low-voltage Thermostat  
Set adjustment lever (CT30 only)  
1
Separate cover from thermostat,  
and remove the plastic insert.  
2
Use a pencil to move the adjust-  
ment lever to the proper setting for  
your system (see table below).  
Your system  
Setting  
Gas or oil furnace  
(
less than 90% efficiency)  
0.4  
0.3  
Electric furnace (any type)  
High efficiency furnace  
(
more than 90% efficiency)  
0.8  
0.8  
1.2  
Hot water system  
Gas/oil steam or gravity system  
Finish installation  
1
2
Align the 3 tabs on  
the cover with slots  
on the thermostat,  
then push gently  
until the cover  
snaps into place.  
Restore electrical  
power at the heat-  
ing/cooling system,  
or at the fuse/  
circuit-breaker  
panel.  
Thermostat  
(shown with  
optional  
cover plate)  
Cover  
5
href="
Owner’s Manual  
Operation  
Temperature setting  
Move lever to adjust desired indoor  
temperature.  
System off (CT33 only)  
Move lever to far left to turn  
off heating system.  
6
href="
CT30/CT33 Low-voltage Thermostat  
Limited Warranty  
Honeywell warrants this product to be free from defects in the workmanship or  
materials, under normal use and service, for a period of one (1) year from the date  
of purchase by the consumer. If at any time during the warranty period the prod-  
uct is determined to be defective or malfunctions, Honeywell shall repair or  
replace it (at Honeywell's option).  
If the product is defective,  
(i) return it, with a bill of sale or other dated proof of purchase, to the place from  
which you purchased it; or  
(ii) call Honeywell Customer Care at 1-800-468-1502. Customer Care will make the  
determination whether the product should be returned to the following address:  
Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley,  
MN 55422, or whether a replacement product can be sent to you.  
This warranty does not cover removal or reinstallation costs.This warranty shall  
not apply if it is shown by Honeywell that the defect or malfunction was caused  
by damage which occurred while the product was in the possession of a  
consumer.  
Honeywell's sole responsibility shall be to repair or replace the product  
within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY  
LOSS OR DAMAGE OF ANY KIND, INCLUDING ANY INCIDENTAL OR CONSE-  
QUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY  
BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF  
THIS PRODUCT. Some states do not allow the exclusion or limitation of incidental  
or consequential damages, so this limitation may not apply to you.  
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON  
THIS PRODUCT.THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING  
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR  
PURPOSE, IS HEREBY LIMITED TO THE ONE-YEAR DURATION OF THIS  
WARRANTY. Some states do not allow limitations on how long an implied  
warranty lasts, so the above limitation may not apply to you.  
This warranty gives you specific legal rights, and you may have other rights which  
vary from state to state.  
If you have any questions concerning this warranty, please write Honeywell  
Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-  
1502. In Canada, write Retail Products ON15-02H, Honeywell Limited/  
Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.  
7
href="
Need Help?  
For assistance with this product please visit www.honeywell.com/yourhome  
or call Honeywell Customer Care toll-free at 1-800-468-1502  
Automation and Control Solutions  
Honeywell International Inc.  
985 Douglas Drive North  
Honeywell Limited-Honeywell Limitée  
35 Dynamic Drive  
1
Golden Valley, MN 55422  
Scarborough, Ontario M1V 4Z9  
www.honeywell.com/yourhome  
Printed in U.S.A. on recycled  
paper containing at least 10%  
post-consumer paper fibers.  
®
©
U.S. Registered Trademark.  
2005 Honeywell International Inc.  
Patents pending. All rights reserved.  
9-1808EF Rev. 03-2005  
6
href="
Guide  
d’utilisation  
CT30/CT33  
Thermostat basse tension  
Éléments nécessaires à l’installation  
Assurez-vous que le paquet contient les éléments suivants :  
Etiquettes de fils  
Carte de mise  
en garde  
Chevilles et vis de  
montage (2 de chaque)  
Thermostat CT30/CT33 Plaque cache-trous  
Outillage et matériel nécessaires :  
Tournevis  
Marteau  
Niveau (facultatif)  
Crayon  
Mèche (3/16”pour cloisons sèches, 7/32”pour cloisons plâtre)  
®
U.S. Marque déposée. Brevets en instance.  
Copyright © 2005 Honeywell International Inc.  
Tous droits réservés.  
href="
Guide d’utilisation  
Retirez l’ancien thermostat  
1
Coupez le courant au niveau de l’installation de chauffage/de climatisation  
ou du panneau de fusibles ou de disjoncteurs).  
(
2. Retirez le boîtier et le thermostat. Laissez la plaque murale et les fils qui y  
sont fixés.  
Laissez la plaque de montage en place  
Le thermostat comporte-t-il un tube scellé  
contenant du mercure ? Si c’est le cas,  
reportez-vous à l’avis concernant le mercure  
ci-dessous.  
Ancien thermostat  
Couvercle  
AVIS CONCERNANT LE MERCURE: Ne placez pas votre vieux thermostat dans les  
ordures s’il contient une ampoule de mercure. Contactez l'agence de gestion des  
déchets de la localité pour connaître les règlements concernant le recyclage et  
la mise au rebut.  
Avez-vous acheté le bon thermostat? Comptez les fils.  
Comptez le nombre de fils sortant du mur et fixés aux bornes de votre ancien  
thermostat. Si aucun d’entre eux n’est fixé à la borne marquée « C » ou « C1 »,  
ne comptez pas ce fil dans le total.  
Si le total (sans compter C ou C1) est de 2 fils, passez à la page suivante. Si le total  
de fils est égal ou supérieur à 3, votre nouveau thermostat risque de ne pas être  
compatible avec votre installation.Arrêtez la pose et demandez conseil au  
1-800-468-1502.  
Comptez-vous 3 fils ou plus? Dans ce cas,  
arrêtez-vous de suite. Vous avez peut-être  
acheté le mauvais thermostat de rechange.  
2
href="
Thermostat basse tension CT30/CT33  
Étiquetez les fils et retirez l’ancienne plaque de montage  
Débranchez les fils un par un à l’aide d’un tournevis. À mesure que vous les  
débranchez, enveloppez-les avec l’étiquette correspondant à la lettre de votre  
ancien thermostat. (Des étiquettes adhésives sont fournies dans l'emballage de  
votre thermostat.)  
Ne retirez l’ancienne plaque qu’une fois tous les fils étiquetés.Veillez à ne pas  
laisser des fils détachés tomber dans l’ouverture du mur.  
Enveloppez soigneusement les étiquettes  
fournies autour de chaque fil.  
Ne laissez pas les fils tomber dans l’ouverture  
du mur!  
NE TENEZ PAS COMPTE DE LA COULEUR DES  
FILS : n'identifiez le type de fil que par une lettre.  
Repérez la position de montage  
1
Mettez la base ou la plaque cache-trous  
de niveau si vous le souhaitez.  
2
Marquez la  
position des  
deux trous de  
vis.  
3
href="
Guide d’utilisation  
Montez la thermostat  
1
Percez des trous aux emplacements repérés au crayon (3/16" pour les cloisons sèches,  
/32” pour le plâtre.  
7
2
Entrez les  
chevilles dans les  
trous avec un  
marteau jusqu’à  
ce qu’elles soient  
de niveau avec le  
mur.  
3
4
[Facultatif] Tirez les  
fils par la plaque  
cache-trous (s’il en  
est besoin pour dis-  
simuler les marques  
laissées par votre  
ancien thermostat).  
Raccordez d’abord  
les fils (voir  
ci-dessous) et  
insérez les vis.  
Vérifiez l'aplomb si  
vous le souhaitez,  
puis serrez les vis.  
Plaque cache-trous en option  
Thermostat  
Raccordez les fils  
1
Faites correspondre fil et borne  
portant la même lettre.  
2
Desserrez les bornes à vis à l’aide  
d’un tournevis, enroulez  
soigneusement les fils dénudés  
autour des bornes et serrez les vis.  
3
Repoussez le fil en trop dans le  
trou du mur.  
Les étiquettes ne correspondent pas ?  
Si les étiquettes ne correspondent pas aux  
lettres marquées sur le thermostat, voir le  
tableau ci-dessous.  
Fils existants  
R RH 4 V  
W  W1  H  
Y Y1 M  
G F  
Raccordez à :  
Terminal “R”  
Face arrière du thermostat  
Terminal “W”  
Reportez-vous à la note  
Reportez-vous à la note  
Reportez-vous à la note  
Si un de ces fils sont Si ce fil est  
présent, vous ne pouvez pas utiliser ce  
thermostat avec votre installation. Voir  
la page 2.  
Rc  
4
href="
Thermostat basse tension CT30/CT33  
Positionnement du levier de réglage (CT30 seulement)  
1
Séparez le couvercle du thermostat  
et retirez la plaquette en plastique.  
2
À l’aide d’un crayon, amenez le  
levier de réglage à l'emplacement  
convenant à votre installation (voir  
le tableau ci-dessous).  
Votre installation  
Réglage  
Chaudière au gaz ou au mazout  
(
de rendement inférieur à 90 %)  
0.4  
0.3  
Chaudière électrique (tous types)  
Chaudière à haut rendement  
(
rendement supérieur à 90 %)  
0.8  
0.8  
1.2  
Installation de chauffage  
à l’eau chaude  
Installation au gaz ou mazout,  
ou à la vapeur, ou calorifère  
Fin de l’installation  
1
Alignez les 3  
languettes du  
couvercle avec les  
fentes du thermo-  
stat, puis poussez  
doucement jusqu’à  
ce que le couvercle  
s’emboîte en place.  
2
Rétablissez le  
courant électrique  
au niveau de  
l’installation de  
chauffage/climatisa-  
tion ou du panneau  
de fusible ou du  
disjoncteur.  
Thermostat  
(représentée  
avec la plaque  
cache-trous en  
option)  
Couvercle  
5
href="
Guide d’utilisation  
Mode d’emploi  
Réglage de la température  
Déplacez le levier pour obtenir la  
température intérieure désirée  
Arrêt de l’installation  
(CT33 seulement)  
Amenez le levier à l’extrême  
gauche pour arrêter  
l’installation de chauffage.  
6
href="
Thermostat basse tension CT30/CT33  
Garantie limitée  
Honeywell garantit ce produit contre tout vis de fabrication ou de matière dans  
des conditions d’utilisation et de service normales, pendant une durée d’un (1) an  
à compter de la date d’achat par le consommateur. Si à un moment quelconque  
pendant la durée de la garantie, le produit est jugé défectueux ou tombe en  
panne, Honeywell le réparera ou le remplacera (au choix d’Honeywell).  
Si le produit est défectueux,  
(i) retournez-le avec un reçu ou une autre preuve d’achat au lieu où vous l’avez  
acheté, ou  
(ii) appelez le service clients d’Honeywell au 1-800-468-1502. Le service clients  
décidera si le produit doit être renvoyé à l’adresse suivante : Honeywell Return  
Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, ou si un  
produit de remplacement peut vous être envoyé.  
Cette garantie ne couvre pas les frais de démontage ou de réinstallation. Elle ne  
s’applique pas si Honeywell prouve que le défaut ou la défaillance provient de  
dommages qui se sont produits pendant que le produit était dans la possession  
d’un acquéreur.  
La responsabilité d’Honeywell se limite à la réparation ou au remplacement du  
produit dans les conditions énoncées ci-dessus. HONEYWELL NE SAURAIT ÊTRE  
RESPONSABLE D'UNE PERTE OU DE DOMMAGES QUELS QU'ILS SOIENT,Y COM-  
PRIS LES DOMMAGES CONSÉCUTIFS OU ACCESSOIRES PROVENANT DIRECTE-  
MENT OU INDIRECTEMENT D'UNE INFRACTION À LA GARANTIE, EXPLICITE  
OU IMPLICITE OU DE TOUTE AUTRE DÉFAILLANCE DE CE PRODUIT. Certains  
états ne permettent pas de limites sur la durée d’une garantie implicite, il se peut  
donc que les limites ci-dessus ne s’appliquent pas à vous.  
CETTE GARANTIE EST LA SEULE GARANTIE EXPLICITE QUE FAIT HONEYWELL  
SUR CE PRODUIT. LA DURÉE DE TOUTES LES GARANTIES IMPLICITES,Y COM-  
PRIS CELLES DE QUALITÉ MARCHANDE ET D’ADAPTATION À UN USAGE PARTI-  
CULIER EST LIMITÉE PAR LA DURÉE D’UN AN DE CETTE GARANTIE. Certains  
états ne permettent pas de limites sur la durée d’une garantie implicite, il se peut  
donc que les limites ci-dessus ne s’appliquent pas à vous.  
Cette garantie vous donne des droits spécifiques face à la loi et vous pouvez en  
avoir d’autres, variables d’un état à un autre.  
Si vous avez des questions concernant cette garantie, écrivez à Honeywell  
Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 ou appelez 1-800-  
468-1502.Au Canada, écrivez à Retail Products ON15-02H, Honeywell  
Limited/Honeywell Limitée, 35 Dynamic Drive, Scarborough, Ontario M1V4Z9.  
7
href="
Vous faut-il de l’aide ?  
Pour obtenir de l’assistance concernant ce produit, visitez www.honeywell.com/yourhome  
ou appelez gratuitement l’assistance client d’Honeywell au 1-800-468-1502  
Automation and Control Solutions  
Honeywell International Inc.  
985 Douglas Drive North  
Honeywell Limited-Honeywell Limitée  
35 Dynamic Drive  
1
Golden Valley, MN 55422  
Scarborough, Ontario M1V 4Z9  
www.honeywell.com/yourhome  
Imprimé aux États-Unis sur du papier  
recyclé contenant au moins 10% de fibres  
de papier récupérées après usage.  
®
©
U.S. Marque déposée.  
2005 Honeywell International Inc.  
Brevets en instance. Tous droits réservés.  
9-1808EF Rev. 03-2005  
6

White Rodgers 1F85 0471 Thermostat User Manual

Lux Products P521U Thermostat User Manual

White Rodgers 829A 845 Thermostat User Manual

Honeywell T8011 Thermostat User Manual

White Rodgers 750 Thermostat User Manual

Honeywell T8132A Thermostat User Manual

Honeywell T921G Thermostat User Manual

White Rodgers F145 1378 Thermostat User Manual

Emerson 1F97 1277 Thermostat User Manual

White Rodgers 700 Thermostat User Manual